Appendix B. Driver Error Messages
Error Message | Explanation | |
DNP:#1 Err. Unknown object=%d | The driver is polling for or responding to a poll for a data object and | |
variation=%d for resp. | ||
variation that is not supported. See Appendix A.9 for a table of | ||
DNP:#2 Err. Unknown object=%d | ||
supported objects. | ||
variation=%d for store. | ||
| ||
DNP:#3 FYI. No nodes to | No DNP 3.0 nodes have been defined in the configuration. The | |
process. | configuration file is probably invalid. 6. | |
DNP:#4 Err. Link Reset node %d | A Client must send a ‘Link Reset Request’ message to this driver | |
failed. (Send a Link Reset Rqst | ||
before it can respond to a poll. | ||
before polling.) | ||
| ||
| Many DNP 3.0 Servers time out the link and the connection must | |
DNP:#5 FYI. Slave=%d happy | be reestablished with a ‘Reset Link Rqst’ message. This driver | |
doesn’t do this. This message is printed when the link has timed out | ||
with link. No reset Rqst. | ||
and a poll is received. The message indicates that this behavior is | ||
| ||
| ok. | |
DNP:#6 FYI. Node=%d requires a | A Client must send a ‘Link Reset Request’ message to this driver | |
reset before it can respond. | before it can respond to a poll. | |
DNP:#7. Err. Too many polls with | When the driver receives too many polls without a link reset request | |
no reset request. | then this message is printed and the driver panics. | |
DNP:#8 Err. Cant reset node=%d | The driver cannot reset the link for the node reported in the | |
message because the node number is too large. Change the Client | ||
(Max=%d) | ||
to poll for a smaller node number.6 | ||
DNP:#9 Err. Unknown | Valid values are provided in Appendix A.3. The driver uses ‘value’ | |
dnpSubType=<%s> | as default if the keyword is not recognized. | |
DNP:#11 FYI. Master Node | The driver is reporting the Node_ID of the Client node. This | |
Address=%d | message is for information only. | |
DNP:#12 FYI. DEBUG Message | You should never see this message. Check the configuration file for | |
being sent. | an illegal DNPDatatype.6 | |
| This message is for information only. When writing to a DNP | |
| device the message contains a function code which may be | |
| overwritten by specifying the DNPfunction in the CSV file. When | |
DNP:#13 FYI. Write function | DNPfunction has not been specified, the default function is used | |
overwritten. MD=<%s> | and this message is printed. When writing to a relay output the | |
| driver uses function code=5 (Direct act with no ack). When writing | |
| to a Counter the driver uses function code=8 (Immed freeze with no | |
| ack). | |
DNP:#14 FYI. Length truncated to | When using DNP qualifier 17, the maximum value for Map | |
255 for MD=<%s> | Descriptor Length is 255. The driver has truncated the request 6 | |
DNP:#15a Err. Cant understand | The qualifier is invalid. Appendix A.11 has a list of valid Qualifiers.6 | |
index portion of qualifier. | ||
Qual=0x%02x for MD=<%s> |
| |
DNP:#16 Err. Previous Poll not | An attempt was made to start a new poll before the previous one | |
completed | completed. A poll might consist of multiple transactions of multiple | |
DNP:#17. Err. Previous Write not | fragments and therefore could take several seconds. Take a log | |
and send with the problem description and the configuration file to | ||
completed | ||
FST Tech support. | ||
| ||
DNP:#18 FYI. Cmd completed but | These messages are printed when the polls for data return with no | |
no (event) data to store. | data. This can be normal if there are no events/ diagnostic data in | |
DNP:#18 FYI. Cmd completed but | ||
the remote device. This message is for information only. | ||
no (diag) data to store. |
|
6Edit the CSV file, download to the FieldServer and reset the FieldServer.
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com