Maxtor Computer Drive manual 2Device Plug Connector Pin Definitions

Page 34

Installation

Table 4-2Device Plug Connector Pin Definitions

Signal Segment

S1

S2

S3

S4

S5

S6

S7

	Ground	2nd Mate
	A+	Differential signal pair A from Phy
	A-	Differential signal pair A from Phy
	A-
	Ground	2nd Mate
	B-	Differential signal pair B from Phy
	B+	Differential signal pair B from Phy
	B+
	Ground	2nd Mate

Signal Segment “L”

Central Connector Polarizer

Power Segment “L”

Power Segment

P1

P2

P3

P4

P5

P6

P7

P8

P9

P10

P11

P12

P13

P14

P15

V33	3.3V power1
V33	3.3V power1
V33	3.3V power, pre-charge, 2nd mate1
Ground	1st mate
Ground	2nd mate2
Ground	2nd mate
V5	5V power, pre-charge, 2nd mate
V5	5V power
V5	5V power
Ground	2nd mate
Reserved	1. The pin corresponding to P11 in the
	backplane receptacle connector is used to
	enable staggered spin-up and activity LED
	features, when used in backplane enviro-
	ments.
	2. The corresponding pin to be mated with
	P11 in the power cable receptacle connec-
	tor will always be grounded.
Ground	1st mate
V12	12V power, pre-charge, 2nd mate
V12	12V power
V12	12V power

POWER SEGMENT KEY

Note 1. 3.3V power is not used by DiamondMax 8S 40GB SATA

Maxtor DiamondMax 8S 40GB SATA 4-11

Image 34

Contents DiamondMax 8S 40GB Serial ATA Product Manual May 13 Revision Part NumberUL/CSA/VDE/TUV /RoHS PatentsClause at Dfars 252.227-7013 and FAR McCarthy Blvd Milpitas, California Tel Fax Table of Contents Sata BUS Interface and ATA Commands InstallationService and Support List of Figures Single Pack Shipping ContainerSata Pin 11 Configuration List of TablesManual Organization Maxtor CorporationAudience ProductsTerminology and Conventions SataReference SOFMaxtor DiamondMax 8S 40GB Sata Product Description KEY Features Serial ATA InterfaceReliability PerformanceVersatility Hardware Requirements Regulatory Compliance StandardsProduct EMI/EMS Qualifications Drive Configuration Product SpecificationsModels and Capacities Physical Dimensions Performance Specifications40GB Power Requirements Power Mode DefinitionsTrack Following EPA Energy Star ComplianceEnvironmental Limits At SpeedShock and Vibration Parameter Operating NON-OPERATINGReliability Specifications Canadian Emissions StatementSafety Regulatory Compliance RoHS ComplianceInstallation Space RequirementsUnpacking Instructions 2Single Pack Shipping Container325 Pack Shipping Container Jumper Position Hardware OptionsStaggered Spin-up 4DiamondMax 8S 40GB Sata Power/Interface Connector SATA-P11 Mounting Orientation6Mounting Dimensions and Clearance Ventilation Sata Bus Interface ConnectorExternal Drive Activity LED Connecting the Adapter Board and the Drive For Systems with AN ADD-IN Sata Adapter Board2Device Plug Connector Pin Definitions 7Drive Power Supply and Sata Bus Interface Cables 8Completing the Drive Installation Mechanical Interface Sata BUS Interface and ATA CommandsCommand Interface Register Address DecodingSupported Commands Command Feature Register Code ValuesCommand Feature Register Code Values DBh Write Mulitple EXT Word Content Description Word Content Description Word Content Description Minimum Multiword DMA transfer cycle time per word ATA Bus Interface and ATA Commands Word Content Description Word Content Description Word Content Description Word Content Description Word Content Description Word Content Description = Ultra DMA mode 6 is selected Word Content Description ATA Bus Interface and ATA Commands Word Content Description Word Content Description Warranty Services Service and SupportProduct Support Glossary Maxtor DiamondMax 8S 40GB Sata G-2 FCI Acronym for flux changes per inch. See also BPI Initialize See low level formatting Kilobyte kB a unit of measure consisting of 1,024 210 bytesMB See megabyte Millisecond ms One thousandth of a second .001 secMaxtor DiamondMax 8S 40GB Sata G-6 Transfer Rate The rate at which Maxtor DiamondMax 8S 40GB Sata G-8 Clearance 4-6,4-7,4-8