Abit AW8 Acpi Suspend Type, Resume by USB From S3, Power Button Function, WakeUp by PME# of PCI

Page 49

BIOS Setup	3-21

ACPI Suspend Type:

This item selects the type of Suspend mode.

[S1(PowerOn-Suspend)]:Enables the Power On Suspend function.

[S3(Suspend-To-RAM)]:Enables the Suspend to RAM function.

!Resume by USB From S3:

When set to [Enabled], this item allows you to use a USB device to wake up a system that is in the S3 (STR - Suspend To RAM) state. This item can be configured only if the item “ACPI Suspend Type” is set to [S3(STR)].

Power Button Function:

This item selects the method of powering off your system:

[Delay 4 Sec.]: Pushing the power button for more than 4 seconds will power off the system. This will prevent the system from powering off in case you accidentally hit or pushed the power button.

[Instant-Off]:Pressing and then releasing the power button at once will immediately power off the system.

WakeUp by PME# of PCI:

When set to [Enabled], access to the onboard LAN or a PCI card such as a modem or LAN card will cause the system to wake up. The PCI card must support the wake up function.

WakeUp by Ring:

Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled, any event affecting from Modem Ring will awaken a system that has powered down.

WakeUp by Alarm:

When set to [Enabled], you can set the date and time you would like the Soft-Off PC to power-on in the “Date (of Month) Alarm” and “Time (hh:mm:ss) Alarm” items. However, if the system is being accessed by incoming calls or the network (Resume On Ring/LAN) prior to the date and time set in these items, the system will give priority to the incoming calls or network instead.

!Date (of Month) Alarm

[0]: This option power-on the system everyday according to the time set in the “Time (hh:mm:ss) Alarm” item.

[1-31]:This option selects a date you would like the system to power-on. The system will power-on on the date set, and the time set in the “Time (hh:mm:ss) Alarm” item.

!Time (hh:mm:ss) Alarm

This item sets the time you would like the system to power-on.

User’s Manual

Image 49

Contents AW8 Series Copyright and Warranty Notice Table of Contents Exit Without Saving Appendix a Introduction Features & SpecificationsBack Panel I/O Layout Diagram Chapter Install The Motherboard Hardware SetupInstall CPU, Heatsink and Fan Assembly User’s Manual Method Channel a Channel B Install System MemoryDIMM1 ATX Power Input Connectors Connectors, Headers and SwitchesFAN Power Connectors Cmos Memory Clearing Header Pin 1-2 shorted default Normal operationUSB-PWR1 Wake-up HeaderBack Panel Audio Connection Slot 10ChapterPdif Connection Hled Pin 1 Front Panel Switches & Indicators HeadersRST Pin 5 Spkr Pin 13, 15, 17Additional IEEE1394 Port Headers Additional USB Port Headers Guru Clock Connection Header Floppy and IDE Disk Drive Connectors Post Code Display Serial ATA Connectors PCI Express x1 Slots PCI Express x16 SlotBack Panel Connectors AW8 Press DEL to Enter Setup Bios SetupOC Guru ΜGuru UtilityBrand Name FrequencyMultiplier Factor External ClockEstimated New CPU Clock Strap CPU AsAbit EQ Beep Control Power Cycle Statistics# Temperature Monitoring All Voltages # Voltage MonitoringHigh/Low Limit CPU/NB/SYS/AUX/OTES FAN Speed # Fan Speed MonitoringLow Limit # FanEQ Control AUX/OTES FanEQ Control Date mmddyy Standard Cmos FeaturesTime hhmmss # Back to Standard Cmos Features Setup Menu Advanced Bios Features # CPU Feature # Back to Advanced Bios Features Setup Menu Advanced Chipset Features # PCI Express Root Port Func # Back to Advanced Chipset Features Setup MenuIntegrated Peripherals On-Chip Sata Mode# On-Chip IDE Device IDE Bus MasterPata IDE Mode Sata Port Speed SettingsOn-Chip Sata Mode# Super-IO Device # On-Chip PCI Device# Onboard PCI Device Power Management SetupWakeUp by Alarm Power Button FunctionDate of Month Alarm Time hhmmss AlarmKB Power on Password Power On FunctionHot Key Power on Restore On AC Power LossPnP/PCI Configurations Load Optimized Defaults Load Fail-Safe DefaultsSet Password Save & Exit SetupNow., and click Finish to complete setup Appendix a Install Intel Matrix Storage Technology RAID Driver Click Next Click Finish to complete setup Appendix C. Install Audio Driver Appendix C Appendix D. Install BCM LAN Driver Appendix D Click OK Appendix E. Install Sil3132 Sata Driver AW8-MAXAppendix E Appendix F. Install USB 2.0 Driver Appendix F Appendix G. Install Abit µGuru Utility Appendix G Award Post Code Definitions Appendix H. Post Code DefinitionDescription Screen logo E8POST.ASM starts AutoInvoke all ISA adapter ROMs Power Off Sequence Hex Description Power On SequenceAC2005 Post Code Definition AW8 Series Appendix I. Troubleshooting Need Assistance? Example Main instructions Contact Person # Fax Number Mail Address ∋ Technical Support FormProduct to you first Appendix J. How to Get Technical SupportAppendix J North America Abit Computer U.S.A. Corporation South America Thank You Abit Computer Corporation