Accell MPC series, MPC-LNK, MPC-816 Series, MPC-68K Series manual MPG-68K, MOP-048, MIP-048

MPG-68K

PG Board (100K) 4-Axis Output, 8-Origin Input

[Characteristics]

This is a board equipped with 4-axis simultaneous-control pulse generation. By an interpreter (ADVFSC®) installed on MPC-68K, programming is possible in a BASIC-like environment. The maximum pulse rate is 100 kpps (for 3-axis simultaneous interpolation). One MPC-68K can support about three MPG-68K boards. If a power source unit (MPS-324) is added, about six boards can be supported.

	(3)	[Specification]
		Power source: DC 12V~24V (for I/O control). Battery retained for 5 years (w/o external
	(1)		power supply at room temperature).
		Pulse output: 4-axis/RS422 specification (photoisolated).
		CPU: TMP68301F-16 16MHz. 1M SRAM*2 + 1M PROM*2.
	(2)	Control I/O: 4-axis output, 8-point origin sensor input.
		Consumed current: 150 mA
		[Accessories]	(1) Power connector (H4P-SHF-AA)	JST	*1
			(2) Contacts (BHF-001T-0.8SS)	JST	*4
			(3) Connector (HIF-3BA-16D-2.54R)	Hirose	*1
MOP-048	48-Point Transistor Output Board				48 Outputs

ACCEL CORP CEP-013B

MOP-048

MIP-048

[Characteristics]

This is a dedicated output board equipped with 48-point output. Each output is equipped with an LED monitor. The output interface is an open collector output using a TD62004, where the control current is 100 mA per one output. Therefore, relays and compact solenoids for air- pressure control can be connected as they are. Also, because it functions even with 5 V, it can be used as a TTL output interface. Addresses can be specified by DIP switches (full decoding). MPC-68K supports up to eight MOP boards.

(1)

[Specification]

Power source: DC 5V~24V (for I/O control). 48-point open collector output.

(2)Consumed current: 80 mA

[Accessories]	(1) Power connector (H4P-SHF-AA)	JST	*1
	(2) Contacts (BHF-001T-0.8SS)	JST	*4
48-Point Photocoupler Input Board			48 Inputs

[Characteristics]

This is a dedicated input board equipped with 48-point input. Each input is equipped with an LED monitor. The input interface is a photocoupler input using a TLP-521, where the control current is 2 mA per one input. Also, because it functions even with 5 V if the resistor array is exchanged, it can be used as a TTL input interface. Addresses can be specified by DIP switches (full decoding). MPC-68K supports up to eight MIP boards. MIP-048 is equipped with a resistor socket for two-line sensor compatibility.

[Specification]

(1)Power source: DC (5V) 12V~24V (for I/O control). 48-point optocoupler input.

*If used with DC 5V, the resistor array needs to be replaced.

(2)Consumed current: 30 mA

[Accessories]	(1) Power connector (H4P-SHF-AA)	JST	*1
	(2) Contacts (BHF-001T-0.8SS)	JST	*4

*Current values indicate standard consumed current TYP values. Please keep 20~50 % room in designing.

*Current values indicate consumed current of the internal DC 5V power source, and the maximum current values with all I/Os ON for the I/O boards.

*[] Current values indicate externally-supplied DC 24V current, and the minimum current values with all I/Os OFF.

-5-