Integra PLA-50V1 instruction manual Connections with Equipment that has a Digital Interface

Page 15

Connecting Your PC or Macintosh Computer

Connecting your PC or Macintosh computer to your plasma monitor will enable you to display your computer’s screen image for an impressive presentation. The plasma monitor supports the signals described on page 47.

To connect a PC, Macintosh or compatible graphics adapter, simply:

1.Turn off the power to your plasma monitor and computer.

2.If your PC does not support XGA/SVGA/VGA you will need to install an XGA/SVGA/VGA graphics board. Consult your computer’s instruction manual for your XGA/SVGA/VGA configuration. If you need to install a new board, see the manual that comes with your new graphics board for installation instructions.

3.The plasma monitor provides signal compatibility up to VESA 16001200 (UXGA). However, it is not recommended to use this resolution due to image readability on the monitors 1365768 native pixel resolution panel.

4.Use the signal cable that’s supplied to connect your PC or Macintosh computer to the plasma monitor. For Macintosh, use the supplied monitor adapter to connect to your computer’s video port.

5.Turn on the plasma monitor and the computer.

6.If the plasma monitor goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you’ve connected to the plasma monitor.

When using a Macintosh with the plasma monitor, the following four display standards are supported using the included Macintosh adapter :

13" fixed mode 16" fixed mode 19" fixed mode 21" fixed mode

The 19" fixed mode is recommended for the plasma monitor.

Connections with Equipment that has a Digital Interface

Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard.

*Use a DVI 29-pin signal cable and the ferrite cores (supplied) when making connections to the RGB3 IN (DVI) connector of the main unit.

Note that the RGB3 IN(DVI) terminal does not support analog RGB input source.

Note:

1.Input TMDS signals conforming to DVI standards. The TMDS input corresponds to 1 link.

2.To maintain display quality, use a cable with a quality prescribedbyDVIstandardsthatiswithin5metersinlength.

Connecting Your Document Camera

You can connect your plasma monitor to a document camera. To do so, simply:

1.Turn off the power to your plasma monitor and document camera.

2.Use a standard video cable to connect your document camera to the Video input on your plasma monitor.

3.Turn on the plasma monitor and the document camera.

Note: Refer to your document camera instruction manual for more information about your camera’s video output requirements.

Connecting Your VCR or Laser Disc Player

Use common RCA cables (not provided) to connect your VCR or laser disc player to your plasma monitor. To make these connections, simply:

1.Turn off the power to your plasma monitor and VCR or laser disc player.

2.Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the Video input on your plasma monitor. Use standard RCA audio patch cords to connect the audio from your VCR or laser disc player to your plasma monitor (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound.

3.Turn on the plasma monitor and the VCR or laser disc player.

Note: Refer to your VCR or laser disc player instruction manual for more information about your equipment’s video output requirements.

Connecting Your DVD Player

You can connect your plasma monitor to a DVD player. To do so, simply:

1.Turn off the power to your plasma monitor and DVD player.

2.Use a standard video cable to connect your DVD player to the Y, Cb, and Cr inputs on your plasma monitor. Or use the DVD-player’s S-Video output. Use a standard S-Video cable to connect to the S-Video input on the plasma monitor.

3.Turn on the plasma monitor and the DVD player.

9

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Page Important Information PrecautionsTo avoid damage and prolong operating life Avertissement PrécautionsDOC avis de conformation Mises en garde et précautions de sécuritéRemarque Contents Ventilation Requirements for enclosure mounting How to Mount the Plasma MonitorIntroduction to the Plasma Monitor PLA-50V1 Features you’ll enjoy includeContents of the Package IntroductionFront View Part Names and FunctionRGB2/ DVD2/ HD2 Rear View/ Terminal BoardRGB/PC Remote Control Unit5MULTI Battery Installation and ReplacementApprox 7m/ 23ft Using the wired remote control modeHandling the remote control unit Operating RangePersonal computer with a digital RGB output InstallationConnections with Equipment that has a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerRight Left External Speaker ConnectionsRGB Pin Assignments and Signal Levels for 15 pin RGB AnalogBasic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWatching with a wide screen manual When watching videos or digital video discsWhen watching high definition video source Wide OperationsWatching computer images with a wide screen When Picture Size is set to OFF Supported resolution  Picture Size settingShowing a couple of pictures on the screen at the same time Selecting the input signals to be displayedAdjusting the OSM controls Multi Screen OperationsMenu Operations OSMOn Screen Menu ControlsMain menu Sub menu Functions  Adjusting the computer image Picture Settings MenuAdjusting the picture  Picture adjustment screen Types of picture modes Example Setting the Theater mode Setting the color temperature Setting the color temperatureExample Setting Once the setting is completed Adjusting the white balance Example Adjusting the White Balance Types of noise reduction Example Setting NR-3Reducing noise in the picture  NR Sound settings menu Sound Settings MenuAdjusting the treble, bass and left/right balance Example Adjusting the bassWhen Auto Picture is OFF Screen Settings MenuAdjusting the Position,Size,Fine Picture,Picture Adj Example Adjusting the vertical position in the normal modeSetting the on-screen display Function Settings MenuAdjusting the position of the menu display Adjusting the position of the menu displayExample Adjusting the position of the menu display To adjust the positionPower management settings Setting the power management for computer imagesExample Turning the power management function on Power management functionDescription Turning the picture back on POWER/STANDBY indicatorGray Level Setting the picture to suit the movieSetting the gray level for the sides of the screen Cinema ModeReducing burn-in of the screen Setting RGB3 ADJExample Setting PLE to Lock When you adjust the RGB3 ADJInverse Resetting to the default valuesPLE OrbiterAudio Input Option Settings MenuSetting the allocation of the audio connectors Setting the BNC connectorsBNC Select Setting a computer image to the correct RGB select screenExample Setting the RGB Select mode to Motion To set the RGB select mode to MotionHD Select modes Setting high definition images to the suitable screen sizeExample Setting the 1080B mode to RGB Select modesPicture Size Setting the picture size for RGB input signalsExample Setting the on mode to OFF Information MenuLanguage settings Setting the language for the menusSetting the video signal format Example Setting the menu display to DeutschNtsc Video signal formatsConnections Type of connector D-Sub 9-pin maleExternal Control ApplicationUnit ID 1 and Unit ID CommandCheck Sum CKS, Error Processing, and ACK Communication FormatCommand Reference List Color Gain Data Audio Mute OnAudio Mute Off OSM SelectBright Gain Data Input Mode RequestSharpness Gain Data Contrast Gain DataRED Gain Data Green Gain DataBlue Gain Data Video ADJ Request Long Life Set Failure Mode RequestAudio Select Set Audio Select RequestTable of Signals Supported Supported resolutionComputer input signals supported by this system Page Symptom Checks Remedy TroubleshootingSignals SpecificationsOnkyo U.S.A. Corporation
Top Page Image Contents