Setting RGB3 ADJ.
When the picture input from the RGB3 input terminal is distorted, select the most appropriate setting from among “1”, “2”, and “3”.
Example: Setting “2”
Reducing burn-in of the screen
The brightness of the screen, the position of the picture, and positive/negative mode are adjusted to reduce burn- in of the screen.
Example: Setting “PLE” to “LOCK”
Press the PROCEED button on the remote control unit to
display MAIN MENU on the screen, then...
1.Use the ▲ and ▼ buttons to select “FUNCTION”, then press the PROCEED button.
The “FUNCTION” screen appears.
2.Use the ▲ and ▼ buttons to select “RGB3 ADJ.”.
F U N C T I O N
OSM | : | ON | |
OSM ADJ. | : | 1 | |
POWER MGT | : | OFF | |
GRAY LEVEL | : | 3 | |
CINEMA MODE | : | ON | |
RGB3 ADJ. |
| : | 1 |
LONG LIFE
RESET
SEL. | ADJ. | EXIT | RETURN |
3.To select “2”...
Use the ◀ and ▶ buttons to select “2”.
The mode switches as follows each time the ◀ or ▶
buton is pressed:
→ 1 ↔ 2 ↔ 3 ←
F U N C T I O N
OSM | : | ON | |
OSM ADJ. | : | 1 | |
POWER MGT | : | OFF | |
GRAY LEVEL | : | 3 | |
CINEMA MODE | : | ON | |
RGB3 ADJ. |
| : | 2 |
LONG LIFE
RESET
SEL. | ADJ. | EXIT | RETURN |
4.Once the setting is completed...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once more.
Information
⬛When you adjust the RGB3 ADJ.
The position of the menu display will change. In such a case, be sure to adjust the position.
⬛Restoring the factory default settings
Select “RESET” under the function menu. Note that this also restores other settings to the factory defaults.
Press the PROCEED button on the remote control unit to display the MAIN MENU on the screen, then proceed as follows.
1.Use the ▲ and ▼ buttons to select “FUNCTION”, then press the PROCEED button.
The “FUNCTION” screen appears.
2.Use the ▲ and ▼ buttons to select “LONG LIFE”, then press the PROCEED button.
F U N C T I O N
OSM | : | ON | |||||
OSM ADJ. | : | 1 |
|
| |||
POWER MGT | : | OFF | |||||
GRAY LEVEL | : | 3 |
|
| |||
CINEMA MODE | : | ON | |||||
RGB3 ADJ. | : | 1 |
|
| |||
LONG LIFE |
|
|
|
|
|
| |
RESET |
|
|
|
|
| ||
SEL. |
|
|
| OK |
|
|
|
PROCEED |
| EXIT | RETURN | ||||
The “LONG LIFE” screen appears.
3.Use the ▲ and ▼ buttons to select “PLE”, then use the ◀ and ▶ buttons to select “LOCK”.
The mode switch changes as follows each time the ◀ or ▶ button is pressed:
AUTO ↔ LOCK
|
| L O N G L I F E |
|
| : LOCK |
PLE |
| |
ORBITER | : OFF | |
INVERSE | : OFF | |
SEL. | ADJ. | EXIT | RETURN |
4.Once the setting is completed...
Press the EXIT button to return to the FUNCTION menu.
To exit the main menu, press the EXIT button twice.
31