Infinite Peripherals 216, KPM-210 Hexadecimal Dump, Maintenance, Changing the paper roll

Page 15

1. INSTALLATION AND USE

When the receive buffer is full, if handshaking is set to XON/XOFF, the printer sends the XOFF ($13) on the serial port.

When the receive buffer has cleared once again, if handshaking is set to XON/XOFF, the printer sends the XON ($11) on the serial port.

1.3 HEXADECIMAL DUMP

This function is used to display the characters received from the communications port; the printer prints out both the hexadecimal code received as well as the corresponding ASCII code.

Once the autotest routine has finished, the printer enters Hexadecimal Dump mode. The printer remains in standby until a key is pressed or characters are received from the communications port; for every 24 characters received (204 dpi version) or every 32 characters received (300 dpi version), it prints hexadecimal values and ASCII codes (if the characters appear underlined, it means the receive buffer is full).

Shown below is an example of a Hexadecimal Dump for the 204 dpi (24 character) version:

48 65 78 61 64 65 63 69 6D 61 6C 20 64 75 6D 70 20 66 75 6E 63 74 69 6F

6E 20 30 31 32 33 34 35 36 37 38 39 61 62 63 64 65 66 67 68 69 6A 6B 6C

6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A

Hexadecimal dump functio

n0123456789abcdefghijkl mnopqrstuvwxyz

1.4 MAINTENANCE

1.4.1 Changing the paper roll

To change the roll of paper, proceed as follows:

1)Position the paper roll (1) so that it unrolls correctly as shown in fig.1.2;

2)Insert the end of the paper roll in the paper load opening on the printing mechanism (2) and wait for the paper to load automatically (see fig. 1.2);

3)Remove the paper from the paper exit opening (3)(4).

(4)N.B.: The paper exit opening may be assembled in one of two positions, depending on the model in use (see fig. 1.2).

www.ipcprint.com 1- 3

KPM210/216

Page 14 Page 16
Image 15
Page 14 Page 16
Contents KPM-210/216 KPM210/216 Front external view Printer ComponentsKPM210/216 Rear external view KPM210/216 Under view Table of Contents Supplies Appendix a Accessories and Spare PartsAccessories Character FontsManual Contents General Safety InformationExplanatory Notes Used in this Manual Unpacking the Printer Introduction 65 mm/sec Printer Features50 mm/sec 60 mm/secTab.1 Printer DescriptionTab.A.3 GND Power SupplyPIN Signal ConnectionsConfiguration Data length 2 7, 8D bits/charCharacters per inch Maintenance Hexadecimal DumpChanging the paper roll Paper load specifications Ax m ax Adjusting paper width Paper jams Re-tighten the fastening screwsTab.A.3 Cleaning the printing head Lower the paper guide 2 as shown in fig Cleaning the ejector rollers Installation and USE PIN Signal IN/OUT Description RS232 SerialDCD KPM80/112 Device USB Serial Interface OptionalPrint Direction Printer FunctionsDescription Command Descriptions1 ESC/POS Emulation Ascii HEXAscii HEX GS Γ GS ΠGS Σ ESC D Back spaceAscii Horizontal tabPrint and carriage return Print and line feedESC 2, ESC Form FeedDLE EOT n Real-time status transmissionAscii DLE EOT =2 Off-line status =17 Print status Byte = User Status Set right-side character spacing Cancel current line transmittedCan ESC SP nGS P or GS $D0 ESC ! nSelect print modes ESC -, ESC E, ESC 4, GS GS ~ESC \, GS P or GS $D0 Select/cancel user-defined charactersESC $ nL nH Set absolute print positionESC &, ESC ? ESC & Y C1 C2 x1 d1…dy ⋅⋅ x1…xkd1…dy ⋅⋅ xkDefines user-defined characters GS * or ESC v nL nHSet relative vertical print position ESC * m nL nH d1...dk Select bit image modeFor the 300 dpi model ESC n Turn underline mode on/offESC Set/reset italic mode ESC 0, ESC 2, GS P or GS $D0ESC 4 n ESC ? n Cancel user-defined charactersESC = n Select peripheral deviceESC D n1...nk NUL ESC &, ESC %ESC @ Initialize printerTurn emphasized mode on/off ESC E nAscii Esce ESC J n Turn double-strike mode on/offESC G n ESC EAscii Escr Reference GS P or GS $D0 ExampleESC R n Select an international character setSet relative print position Set 90 rotated print modeESC V n ESC !, ESC ESC \ nL nHJustification ESC $, GS P or GS $D0ESC a n Select justificationESC d n Enable/disable front panel buttonsESC c 5 n FeedESC t n ESC 2 or ESCReference ESC 2, ESC 3 Example Total cutTransmit paper sensor status ESCHex Decimal 123 n Range ≤ n ≤ Description Print graphic Set/cancel cpi modeESC⊥ ⊥ n ESC · n xH xL yH yLTransmit graphic page to communication port ESC ³, ESC ², ESC1BH FAH 00H ESC ¹ nL nHReference ESC ·, ESC ², ESC Example Reference ESC ³, ESC ², ESCESC ³ n Ascii ESC ³ESC ·, ESC ³, ESC ESC ² nL nHReceive graphic page from communication port Ascii ESC ²ESC ·, ESC ², ESC ³ GS ! nSelect character size Start/end macro definition GS B n Name Turn white/black reverse printing mode on/offSelect counter print mode ESC $ and ESC \GS C 0 n m Select count mode a GS C 1, GS C 2, GS C , GS cGS C 1 aL aH bL bH n r GS C 2 nL nH Set counterGS C 0, GS C 1, GS C , GS c Select count mode B GS C sa sb sn sr scAscii GS C Tion HRI characters GS C 0, GS C 2, GS C 1, GS cGS H n Select printing position of Human Readable Interpreta= 2, Type ID GS L nL nH Set left marginGS P or GS $D0, GS W GS W nL nH GS P x y modeCommands using y ESC 3, ESC J Set horizontal and vertical motion units Tab.A.3GS L, GS P GS r t mExecute macro Print counter GS cEjector commands Reference GS C 0, GS C1, GS C 2, GS CGS e n m GS f n Select font for HRI charactersGS H, GS k Ascii GS Set bar code heightPrint bar code Ascii GS NULBar code system No. of characters Remarks Printer Functions Transmit status Code CReference GS H, GS f, GS h, GS w GS r nDLE EOT, ESC u, ESC GS w nSet bar code width GS k GS nSet printing density ESC !, GS GS $D0 xH xL yH yL modeGS ~ n Set superscript/subscriptDirection Enable / disable automatic Full Status backOnce enable at least one byte of the Full STATUS, for Gsγγ Reading number of cuts performed from the printerName Reading of length cm of printed paper GSσσ Name Reading Number of power up GsσσName Reading Number of retracting GS∝∝ nH nL Virtual paper-end limitSet printing speed and current consumption $14 $1A Hardware resetPrinting method ResolutionPaper specifications Printing modeOptions 210 mm 30 cpi Character density 17 cpiShows the dimensions of the table top printer DimensionsCharacter Sets Character SetsTab.A.3 PC865 Accessories Input SpecificationsOutput Specifications Fig.A.2 External roll holderFig.A.3 Assembly InstructionsFig.A.4 View from below Sensor wiring Supplies

216, KPM-210 specifications

Infinite Peripherals, a leader in mobile technology solutions, has developed the KPM-210 and KPM-216 devices, renowned for their robust design and multifunctional capabilities. These handheld devices are primarily targeted toward retail and hospitality sectors, providing an ideal solution for businesses seeking enhanced operational efficiency and customer engagement.

One of the standout features of the KPM-210 and KPM-216 is their ability to function as both a mobile point-of-sale (mPOS) and a mobile printer. This versatility allows businesses to streamline their operations by reducing the need for separate devices. Both models are equipped with high-speed printing technology that ensures quick printouts, significantly improving service times during peak hours.

The KPM-210 features a thermal printer with a 58mm printing width, while the KPM-216 offers a slightly wider 80mm option. This adaptability caters to various business needs, from printing receipts to generating tickets or labels. Additionally, the devices support multiple connectivity options, including Bluetooth, USB, and Wi-Fi, ensuring seamless integration with existing systems and easy updates.

Designed with user experience in mind, both models are compact and lightweight, making them highly portable. Their ergonomic design allows for comfortable handling, even during extended use. The devices also feature a long-lasting battery life, enabling users to operate continuously without frequent recharges, which is essential for busy retail environments or outdoor events.

In terms of durability, the KPM-210 and KPM-216 are built to withstand the rigors of daily use. They boast a solid construction that protects against drops and spills, ensuring reliability in demanding settings. Furthermore, with an IP54 rating, these devices are resistant to dust and splashes, making them suitable for use in various environments.

Another notable characteristic of Infinite Peripherals’ KPM series is their advanced software compatibility. The devices support various operating systems, including iOS, Android, and Windows, allowing businesses to integrate them into their current ecosystems effortlessly. This flexibility enables users to leverage their existing applications while benefiting from the capabilities of the KPM-210 and KPM-216.

In conclusion, the Infinite Peripherals KPM-210 and KPM-216 are innovative devices designed to meet the evolving needs of modern businesses. With their multifunctional capabilities, robust design, and user-friendly features, these handheld solutions are set to enhance operational efficiency and elevate customer experiences across various industries.
Top Page Image Contents