Infinite Peripherals KPM-210, 216 user manual ESC $ and ESC, GS C 0 n m, Select counter print mode

Page 66

3. PRINTER FUNCTIONS

[Description]

Turns white/black reverse printing mode on or off.

 

• When the LSB of n is 0, white/black reverse printing is

 

turned off.

 

• When the LSB of n is 1, white/black reverse printing is

 

turned on.

[Notes]

• Only the LSB di n is effective.

 

• This command is available for both built-in and user-defined

 

characters.

 

• This command does not affect bit image, downloaded bit

 

image, bar code, HRI characters and spacing skipped by HT,

 

ESC $ and ESC \.

 

• This command does not affect white space between lines.

 

• White/black reverse mode has a higher priority than under-

 

line mode. Even if underline mode is on, it will be disabled

 

(but not cancelled) when white/black reverse mode is se-

 

lected.

[Default]

n = 0

[Reference]

 

[Example]

 

GS C 0 n m

[Name]

Select counter print mode

 

 

[Format]

ASCII

GS

C

0

n

m

 

Hex

1D

43

30

n

m

 

Decimal

29

67

48

n

m

[Range]

0 ≤ n ≤ 5

 

 

 

 

 

 

m = 0, 1, 2, 48, 49, 50

 

 

 

[Description]

Selects a print mode for the serial number counter.

•n specifies the number of digits to be printed as follows: when n = 0, the printer prints the actual digits indicated by the numeric value.

when n = 1 to 5, the command sets the number of digits to be printed.

•m specifies the printing position within the entire range of printed digits as follows:

www.ipcprint.com 3-39

KPM210/216

Page 65 Page 67
Image 66
Page 65 Page 67
Contents KPM-210/216 Printer Components KPM210/216 Front external viewKPM210/216 Rear external view KPM210/216 Under view Table of Contents Character Fonts Appendix a Accessories and Spare PartsAccessories SuppliesManual Contents General Safety InformationExplanatory Notes Used in this Manual Unpacking the Printer Introduction 60 mm/sec Printer Features50 mm/sec 65 mm/secPrinter Description Tab.1Tab.A.3 Connections Power SupplyPIN Signal GNDConfiguration Data length 2 7, 8D bits/charCharacters per inch Maintenance Hexadecimal DumpChanging the paper roll Paper load specifications Ax m ax Adjusting paper width Re-tighten the fastening screws Paper jamsTab.A.3 Cleaning the printing head Lower the paper guide 2 as shown in fig Cleaning the ejector rollers Installation and USE PIN Signal IN/OUT Description RS232 SerialDCD KPM80/112 USB Serial Interface Optional DevicePrinter Functions Print DirectionAscii HEX Command Descriptions1 ESC/POS Emulation DescriptionAscii HEX GS Γ GS ΠGS Σ Horizontal tab Back spaceAscii ESC DForm Feed Print and line feedESC 2, ESC Print and carriage returnDLE EOT n Real-time status transmissionAscii DLE EOT =2 Off-line status =17 Print status Byte = User Status ESC SP n Cancel current line transmittedCan Set right-side character spacingGS P or GS $D0 ESC ! nSelect print modes GS ~ ESC -, ESC E, ESC 4, GSSet absolute print position Select/cancel user-defined charactersESC $ nL nH ESC \, GS P or GS $D0ESC &, ESC ? ESC & Y C1 C2 x1 d1…dy ⋅⋅ x1…xkd1…dy ⋅⋅ xkDefines user-defined characters GS * or ESC v nL nHSet relative vertical print position Select bit image mode ESC * m nL nH d1...dkFor the 300 dpi model Turn underline mode on/off ESC nESC Set/reset italic mode ESC 0, ESC 2, GS P or GS $D0ESC 4 n Select peripheral device Cancel user-defined charactersESC = n ESC ? nInitialize printer ESC &, ESC %ESC @ ESC D n1...nk NULTurn emphasized mode on/off ESC E nAscii Esce ESC E Turn double-strike mode on/offESC G n ESC J nSelect an international character set Reference GS P or GS $D0 ExampleESC R n Ascii EscrESC !, ESC ESC \ nL nH Set 90 rotated print modeESC V n Set relative print positionSelect justification ESC $, GS P or GS $D0ESC a n JustificationFeed Enable/disable front panel buttonsESC c 5 n ESC d nTotal cut ESC 2 or ESCReference ESC 2, ESC 3 Example ESC t nESC Transmit paper sensor statusHex Decimal 123 n Range ≤ n ≤ Description ESC · n xH xL yH yL Set/cancel cpi modeESC⊥ ⊥ n Print graphicESC ¹ nL nH ESC ³, ESC ², ESC1BH FAH 00H Transmit graphic page to communication portAscii ESC ³ Reference ESC ³, ESC ², ESCESC ³ n Reference ESC ·, ESC ², ESC ExampleAscii ESC ² ESC ² nL nHReceive graphic page from communication port ESC ·, ESC ³, ESCESC ·, ESC ², ESC ³ GS ! nSelect character size GS B n Name Turn white/black reverse printing mode on/off Start/end macro definitionSelect counter print mode ESC $ and ESC \GS C 0 n m Select count mode a GS C 1, GS C 2, GS C , GS cGS C 1 aL aH bL bH n r GS C 2 nL nH Set counterGS C 0, GS C 1, GS C , GS c Select count mode B GS C sa sb sn sr scAscii GS C Select printing position of Human Readable Interpreta GS C 0, GS C 2, GS C 1, GS cGS H n Tion HRI characters= 2, Type ID GS L nL nH Set left marginGS P or GS $D0, GS W Set horizontal and vertical motion units Tab.A.3 GS P x y modeCommands using y ESC 3, ESC J GS W nL nHGS L, GS P GS r t mExecute macro GS c Print counterEjector commands Reference GS C 0, GS C1, GS C 2, GS CGS e n m GS f n Select font for HRI charactersGS H, GS k Ascii GS NUL Set bar code heightPrint bar code Ascii GSBar code system No. of characters Remarks Printer Functions GS r n Code CReference GS H, GS f, GS h, GS w Transmit statusDLE EOT, ESC u, ESC GS w nSet bar code width GS k GS nSet printing density Set superscript/subscript GS $D0 xH xL yH yL modeGS ~ n ESC !, GSEnable / disable automatic Full Status back DirectionOnce enable at least one byte of the Full STATUS, for Gsγγ Reading number of cuts performed from the printerName Reading of length cm of printed paper GSσσ Name Reading Number of power up GsσσName Reading Number of retracting GS∝∝ nH nL Virtual paper-end limitSet printing speed and current consumption Hardware reset $14 $1APrinting mode ResolutionPaper specifications Printing methodOptions 210 mm Character density 17 cpi 30 cpiDimensions Shows the dimensions of the table top printerCharacter Sets Character SetsTab.A.3 PC865 Accessories Input SpecificationsOutput Specifications External roll holder Fig.A.2Assembly Instructions Fig.A.3Fig.A.4 View from below Sensor wiring Supplies

216, KPM-210 specifications

Infinite Peripherals, a leader in mobile technology solutions, has developed the KPM-210 and KPM-216 devices, renowned for their robust design and multifunctional capabilities. These handheld devices are primarily targeted toward retail and hospitality sectors, providing an ideal solution for businesses seeking enhanced operational efficiency and customer engagement.

One of the standout features of the KPM-210 and KPM-216 is their ability to function as both a mobile point-of-sale (mPOS) and a mobile printer. This versatility allows businesses to streamline their operations by reducing the need for separate devices. Both models are equipped with high-speed printing technology that ensures quick printouts, significantly improving service times during peak hours.

The KPM-210 features a thermal printer with a 58mm printing width, while the KPM-216 offers a slightly wider 80mm option. This adaptability caters to various business needs, from printing receipts to generating tickets or labels. Additionally, the devices support multiple connectivity options, including Bluetooth, USB, and Wi-Fi, ensuring seamless integration with existing systems and easy updates.

Designed with user experience in mind, both models are compact and lightweight, making them highly portable. Their ergonomic design allows for comfortable handling, even during extended use. The devices also feature a long-lasting battery life, enabling users to operate continuously without frequent recharges, which is essential for busy retail environments or outdoor events.

In terms of durability, the KPM-210 and KPM-216 are built to withstand the rigors of daily use. They boast a solid construction that protects against drops and spills, ensuring reliability in demanding settings. Furthermore, with an IP54 rating, these devices are resistant to dust and splashes, making them suitable for use in various environments.

Another notable characteristic of Infinite Peripherals’ KPM series is their advanced software compatibility. The devices support various operating systems, including iOS, Android, and Windows, allowing businesses to integrate them into their current ecosystems effortlessly. This flexibility enables users to leverage their existing applications while benefiting from the capabilities of the KPM-210 and KPM-216.

In conclusion, the Infinite Peripherals KPM-210 and KPM-216 are innovative devices designed to meet the evolving needs of modern businesses. With their multifunctional capabilities, robust design, and user-friendly features, these handheld solutions are set to enhance operational efficiency and elevate customer experiences across various industries.
Top Page Image Contents