Infinite Peripherals 216 ESC 2 or ESC, Reference ESC 2, ESC 3 Example, Total cut, ESC t n

Page 57

3. PRINTER FUNCTIONS

ESC 2 or ESC 3.

•The maximum paper feed amount is 254 rows. Even if a paper feed amount of more than 254 rows is set,(Tabthe.A.3)printer feeds the paper only 254 rows.

[Default]

[Reference] ESC 2, ESC 3 [Example]

ESC i

[Name]	Total cut
[Format]	ASCII	ESC	i
	Hex	1B	69
	Decimal	27	105
[Description]	This command prints the data in the buffer and enables cutter
	operation. If there is no cutter, a disabling flag is set and any
	subsequent cut commands will be ignored.
[Notes]	• The printer waits to complete all paper movement com-
	mands before it executes a total cut.
[Default]
[Reference]
[Example]

ESC t n

[Name]	Select character code table
[Format]	ASCII	ESCt		n
	Hex	1B	74	n
	Decimal	27	116 n
[Range]	n = 0, 2, 3, 4, 5, 19, 255
[Description]	Selects a page n from the character code table, as follows:

KPM210/216

3- 30 www.ipcprint.com

Image 57

Contents KPM-210/216 KPM210/216 Front external view Printer ComponentsKPM210/216 Rear external view KPM210/216 Under view Table of Contents Accessories Appendix a Accessories and Spare PartsCharacter Fonts SuppliesManual Contents General Safety InformationExplanatory Notes Used in this Manual Unpacking the Printer Introduction 50 mm/sec Printer Features60 mm/sec 65 mm/secTab.1 Printer DescriptionTab.A.3 PIN Signal Power SupplyConnections GNDConfiguration Data length 2 7, 8D bits/charCharacters per inch Maintenance Hexadecimal DumpChanging the paper roll Paper load specifications Ax m ax Adjusting paper width Paper jams Re-tighten the fastening screwsTab.A.3 Cleaning the printing head Lower the paper guide 2 as shown in fig Cleaning the ejector rollers Installation and USE PIN Signal IN/OUT Description RS232 SerialDCD KPM80/112 Device USB Serial Interface OptionalPrint Direction Printer Functions1 ESC/POS Emulation Command DescriptionsAscii HEX DescriptionAscii HEX GS Γ GS ΠGS Σ Ascii Back spaceHorizontal tab ESC DESC 2, ESC Print and line feedForm Feed Print and carriage returnDLE EOT n Real-time status transmissionAscii DLE EOT =2 Off-line status =17 Print status Byte = User Status Can Cancel current line transmittedESC SP n Set right-side character spacingGS P or GS $D0 ESC ! nSelect print modes ESC -, ESC E, ESC 4, GS GS ~ESC $ nL nH Select/cancel user-defined charactersSet absolute print position ESC \, GS P or GS $D0ESC &, ESC ? ESC & Y C1 C2 x1 d1…dy ⋅⋅ x1…xkd1…dy ⋅⋅ xkDefines user-defined characters GS * or ESC v nL nHSet relative vertical print position ESC * m nL nH d1...dk Select bit image modeFor the 300 dpi model ESC n Turn underline mode on/offESC Set/reset italic mode ESC 0, ESC 2, GS P or GS $D0ESC 4 n ESC = n Cancel user-defined charactersSelect peripheral device ESC ? nESC @ ESC &, ESC %Initialize printer ESC D n1...nk NULTurn emphasized mode on/off ESC E nAscii Esce ESC G n Turn double-strike mode on/offESC E ESC J nESC R n Reference GS P or GS $D0 ExampleSelect an international character set Ascii EscrESC V n Set 90 rotated print modeESC !, ESC ESC \ nL nH Set relative print positionESC a n ESC $, GS P or GS $D0Select justification JustificationESC c 5 n Enable/disable front panel buttonsFeed ESC d nReference ESC 2, ESC 3 Example ESC 2 or ESCTotal cut ESC t nTransmit paper sensor status ESCHex Decimal 123 n Range ≤ n ≤ Description ESC⊥ ⊥ n Set/cancel cpi modeESC · n xH xL yH yL Print graphic1BH FAH 00H ESC ³, ESC ², ESCESC ¹ nL nH Transmit graphic page to communication portESC ³ n Reference ESC ³, ESC ², ESCAscii ESC ³ Reference ESC ·, ESC ², ESC ExampleReceive graphic page from communication port ESC ² nL nHAscii ESC ² ESC ·, ESC ³, ESCESC ·, ESC ², ESC ³ GS ! nSelect character size Start/end macro definition GS B n Name Turn white/black reverse printing mode on/offSelect counter print mode ESC $ and ESC \GS C 0 n m Select count mode a GS C 1, GS C 2, GS C , GS cGS C 1 aL aH bL bH n r GS C 2 nL nH Set counterGS C 0, GS C 1, GS C , GS c Select count mode B GS C sa sb sn sr scAscii GS C GS H n GS C 0, GS C 2, GS C 1, GS cSelect printing position of Human Readable Interpreta Tion HRI characters= 2, Type ID GS L nL nH Set left marginGS P or GS $D0, GS W Commands using y ESC 3, ESC J GS P x y modeSet horizontal and vertical motion units Tab.A.3 GS W nL nHGS L, GS P GS r t mExecute macro Print counter GS cEjector commands Reference GS C 0, GS C1, GS C 2, GS CGS e n m GS f n Select font for HRI charactersGS H, GS k Print bar code Set bar code heightAscii GS NUL Ascii GSBar code system No. of characters Remarks Printer Functions Reference GS H, GS f, GS h, GS w Code CGS r n Transmit statusDLE EOT, ESC u, ESC GS w nSet bar code width GS k GS nSet printing density GS ~ n GS $D0 xH xL yH yL modeSet superscript/subscript ESC !, GSDirection Enable / disable automatic Full Status backOnce enable at least one byte of the Full STATUS, for Gsγγ Reading number of cuts performed from the printerName Reading of length cm of printed paper GSσσ Name Reading Number of power up GsσσName Reading Number of retracting GS∝∝ nH nL Virtual paper-end limitSet printing speed and current consumption $14 $1A Hardware resetPaper specifications ResolutionPrinting mode Printing methodOptions 210 mm 30 cpi Character density 17 cpiShows the dimensions of the table top printer DimensionsCharacter Sets Character SetsTab.A.3 PC865 Accessories Input SpecificationsOutput Specifications Fig.A.2 External roll holderFig.A.3 Assembly InstructionsFig.A.4 View from below Sensor wiring Supplies

216, KPM-210 specifications

Infinite Peripherals, a leader in mobile technology solutions, has developed the KPM-210 and KPM-216 devices, renowned for their robust design and multifunctional capabilities. These handheld devices are primarily targeted toward retail and hospitality sectors, providing an ideal solution for businesses seeking enhanced operational efficiency and customer engagement.

One of the standout features of the KPM-210 and KPM-216 is their ability to function as both a mobile point-of-sale (mPOS) and a mobile printer. This versatility allows businesses to streamline their operations by reducing the need for separate devices. Both models are equipped with high-speed printing technology that ensures quick printouts, significantly improving service times during peak hours.

The KPM-210 features a thermal printer with a 58mm printing width, while the KPM-216 offers a slightly wider 80mm option. This adaptability caters to various business needs, from printing receipts to generating tickets or labels. Additionally, the devices support multiple connectivity options, including Bluetooth, USB, and Wi-Fi, ensuring seamless integration with existing systems and easy updates.

Designed with user experience in mind, both models are compact and lightweight, making them highly portable. Their ergonomic design allows for comfortable handling, even during extended use. The devices also feature a long-lasting battery life, enabling users to operate continuously without frequent recharges, which is essential for busy retail environments or outdoor events.

In terms of durability, the KPM-210 and KPM-216 are built to withstand the rigors of daily use. They boast a solid construction that protects against drops and spills, ensuring reliability in demanding settings. Furthermore, with an IP54 rating, these devices are resistant to dust and splashes, making them suitable for use in various environments.

Another notable characteristic of Infinite Peripherals’ KPM series is their advanced software compatibility. The devices support various operating systems, including iOS, Android, and Windows, allowing businesses to integrate them into their current ecosystems effortlessly. This flexibility enables users to leverage their existing applications while benefiting from the capabilities of the KPM-210 and KPM-216.

In conclusion, the Infinite Peripherals KPM-210 and KPM-216 are innovative devices designed to meet the evolving needs of modern businesses. With their multifunctional capabilities, robust design, and user-friendly features, these handheld solutions are set to enhance operational efficiency and elevate customer experiences across various industries.