Foxconn 661M03 user manual Change Password Introduction, Recover Hard disk Data

Page 104

Chapter 6 Special BIOS Functions

3.Recover Hard disk Data:

This option is used to restore the backed up data from the hidden partition.

4.Back to Main:

This option is used to exit the Recovery interface.

CHANGE PASSWORD Introduction:

Select CHANGE PASSWORD to enter the Change Password interface. A. Enter the old password first. Press <Enter> if password is null. B. Enter the new password. Then enter the same again to confirm it. C. Press <Enter> for null password.

D. The password will be saved in the hidden partition.

96	661M03 Series User Manual

Image 104

Contents Version Item Checklist Declaration of conformity HON HAI Precision Industry Table of Contents Chapter Directions for Bundled Software Chapter Special Bios FunctionsChapter Driver CD Introduction Page Page Page Main Features Onboard 1394 optional Onboard LANOnboard I/O Onboard GraphicsAdvanced Features Green FunctionMotherboard Layout ATX 12V connector ATX power connectorPHY optional AGP slotFloppy disk connector IDE connectorsFlash Rom South Bridge controllerInstallation Instructions Installation Instructions Installation of CPU CPUInstallation of CPU Fan Installation Instructions Frequence CPU Qualified Vendor ListVendor Type Installation of DDR Memory MemoryMemory Qualified Vendor List Vender Type SizeChapter Installation Instructions Pin ATX12V Power Connector PWR2 Power SupplyPin ATX power connector PWR1 Rear Panel Connectors This motherboard provides the ports as belowLine-in Line-out Front channels Microphone HDD connectors IDE1 & IDE2 Other ConnectorsFDD Connector Front Panel Connector FP1 IrDA Header IR optional USB Headers FusbFan Connectors CPUFAN, FAN1 Audio Connectors CdinHeader F1394 optional Wake-Up On LAN WOLPdif Out Connector Spdout Audio Interface FaudioAGP Slot Expension SlotsPCI Slots Vender Type Video Memory Installing an expansion cardAGP Qualified Vendor List CNR Slot optional Clear Cmos Jumper Clscmos JumpersDescription of Jumpers BIOS-Protection Jumper Fwhen CNR Audio Selection Jumper J24Powering off the computer Starting up for the first timeBios Description Enter Bios Setup Press TAB to show Post screen, DEL to enter SetupStandard Cmos Features Bios FeaturesAdvanced Bios Features Advanced Chipset FeaturesPower Management Setup PnP/PCI ConfigurationsStandard Cmos Features DateTime IDE Primary/Secondary Master/SlaveHalt On Drive A/BVideo Memory Bios Features SuperBoot SuperBoot Default DisabledAdvanced Bios Features Quick Power On Self Test Default Enabled First/Second/Third Boot Device Default Floppy/HDD- 0/CDROMBoot Other Device Default Enabled Swap Floppy Drive Default DisabledTypematic Delay Msec Default Security Option Default SetupApic Mode Default Enabled MPS Version Control For OS DefaultTM2 Bus VID Default Thermal Management Default Thermal MonitorTM2 Bus Ratio Default 0 Advanced Chipset Features Performance Mode Default Disabled Dram Timing control Default By SPDDram CAS Latency Default 2.5T RAS Active Time tRAS Default 6TAGP Aperture Size Default 64 MB Graphic Window WR Combin Default DisabledAGP Fast Write Support Default Enabled AGP Data Rate Default AutoVGA Share Memory Size Default 32 MB Graphics Engin Clock Default 133 MHzIntegrated Peripherals Audio Access Interface Default EDB Bus Internal PCI/IDE Default BothIDE Primary/ Secondary Master/Slave PIO Default Auto Primary/Secondary Master/Slave UltraDMA Default AutoSIS USB Controller Default Enabled USB Ports Number Default 6 portsUSB 2.0 Supports Default Enabled USB Keyboard Support Default EnabledOnboard FDC Controller Default Enabled Onboard Serial Port1/2 Default 3F8/IRQ4 / 2F8/IRQ3Uart Mode Select Default Normal UR2 Duplex Mode Default HalfPower Management Setup Acpi function Default EnabledAcpi Suspend Type Default S1POS Power Management Default User DefineVideo Off Option Default Susp, Stby off Video Off Method Default Dpms SupportedSwitch Function Default Break/Wake Modem Use IRQ Default AutoIRQ 3-7,9-15, NMI Default Enabled IRQ 8 Break Suspend Default DisabledRing Power Up Control Default Enabled Macpme Power Up Control Default EnabledMonth Alarm Day of Month AlarmTime hhmmss Alarm Primary/Secondary IDE Default DisabledPnP/PCI Configurations Reset Configuration Data Default DisabledResources Controlled By Default AutoESCD PCI/VGA Palette Snoop Default DisabledPC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Password Enter PasswordSave & Exit Setup Exit Without SavingSave to Cmos and Exit Y/N?Y Quit Without Saving Y/N?NChapter Utility CD content Install DriverAccessories Browse CDStart to Install divers Install IDE DriverInstall AGP Driver Install VGA DriverInstall DirectX Installing the Audio Driver Install USB 2.0 DriverUsing 4-/6-Channel Audio Attaching Speakers Channel Analog Audio OutputLine-out Rear channels Line-out Front channels Microphone Selecting 4- or 6-Channel Setting Digital Audio OutputClick the Speaker Configuration tab Testing Each Speaker Playing KaraokeInstall LAN Driver Install Norton Internet Security Directions for Bundled Software SuperStep features Using SuperStepDirections for Bundled Software Directions for Bundled Software SuperLogo features Using SuperLogoDirections for Bundled Software SuperUpdate features Using SuperUpdateDirections for Bundled Software Backup Bios to local image Directions for Bundled Software Directions for Bundled Software Update Bios On-line Click OK to update Bios Click Restart Special Bios Functions SuperSpeed SuperBoot SuperBIOS-Protect SuperRecovery Hotkey SelectionHard Disk Selection What is a Hidden Partition? Main MenuDivide Hidden Partition Divide Hidden PartitionRelease Hidden Partition Backup Partition Table BackupBackup Cmos Setup Backup Hard disk Data Recovery Back to MainRecover Cmos Setup Recover Partition TableChange Password Introduction Recover Hard disk Data