Foxconn 661M03 Quick Power On Self Test Default Enabled, Boot Other Device Default Enabled

Page 48

Chapter 3 BIOS Description

Quick Power On Self Test (Default: Enabled)

Enable this option to shorten the power on testing (POST) and have your sys- tem start up faster. The available setting values are: Disabled and Enabled.

First/Second/Third Boot Device (Default: Floppy/HDD- 0/CDROM)

This option allows you to set the boot device’s sequence. The available setting values are: Floppy, LS120, HDD-0, SCSI, CDROM, HDD-1, HDD-2, HDD-3, ZIP100, USB-FDD, USB-ZIP, USB-CDROM, USB-HDD, LAN and Disabled.

Boot Other Device (Default: Enabled)

With this function set to enable, the system will to boot from some other devices if the first/second/third boot devices failed. The available setting val- ues are: Disabled and Enabled.

Swap Floppy Drive (Default: Disabled)

If you have two floppy diskette drivers in your system, this option allows you to swap the assigned drive letters. The available setting values are: Disabled and Enabled.

Boot Up Floppy Seek (Default: Disabled)

If this option is enabled, BIOS will activate the floppy drive during the system boot and the drive’s indicator will flash after the activation. The magnetic head will move back and forth from A to B. The available setting values are: Disabled and Enabled.

Boot Up NumLock Status (Default: On)

This option defines if the keyboard Num Lock key is active when your system is started. The available setting values are: On and Off.

Gate A20 Option (Default: Fast)

This option is used to set up the A20 signal control necessary for access to the 1MB memory. The available setting values are: Normal and Fast.

Typematic Rate Setting (Default: Disabled)

If this option is enabled, you can use the following two items to see the typematic rate and the typematic delay settings for your keyboard. The available setting values are: Disabled and Enabled.

Typematic Rate (Chars/Sec) (Default: 6)

Use this option to define how many characters per second a held-down key generated.

40	661M03 Series User Manual

Image 48

Contents Version Item Checklist Declaration of conformity HON HAI Precision Industry Table of Contents Chapter Special Bios Functions Chapter Driver CD IntroductionChapter Directions for Bundled Software Page Page Page Main Features Onboard 1394 optional Onboard LANOnboard I/O Onboard GraphicsAdvanced Features Green FunctionMotherboard Layout ATX 12V connector ATX power connectorPHY optional AGP slotFloppy disk connector IDE connectorsFlash Rom South Bridge controllerInstallation Instructions Installation Instructions Installation of CPU CPUInstallation of CPU Fan Installation Instructions CPU Qualified Vendor List Vendor TypeFrequence Installation of DDR Memory MemoryMemory Qualified Vendor List Vender Type SizeChapter Installation Instructions Power Supply Pin ATX power connector PWR1Pin ATX12V Power Connector PWR2 Rear Panel Connectors This motherboard provides the ports as belowLine-in Line-out Front channels Microphone Other Connectors FDD ConnectorHDD connectors IDE1 & IDE2 Front Panel Connector FP1 IrDA Header IR optional USB Headers FusbFan Connectors CPUFAN, FAN1 Audio Connectors CdinHeader F1394 optional Wake-Up On LAN WOLPdif Out Connector Spdout Audio Interface FaudioExpension Slots PCI SlotsAGP Slot Installing an expansion card AGP Qualified Vendor ListVender Type Video Memory CNR Slot optional Jumpers Description of JumpersClear Cmos Jumper Clscmos BIOS-Protection Jumper Fwhen CNR Audio Selection Jumper J24Powering off the computer Starting up for the first timeBios Description Enter Bios Setup Press TAB to show Post screen, DEL to enter SetupStandard Cmos Features Bios FeaturesAdvanced Bios Features Advanced Chipset FeaturesPower Management Setup PnP/PCI ConfigurationsStandard Cmos Features DateTime IDE Primary/Secondary Master/SlaveDrive A/B VideoHalt On Memory Bios Features SuperBoot SuperBoot Default DisabledAdvanced Bios Features Quick Power On Self Test Default Enabled First/Second/Third Boot Device Default Floppy/HDD- 0/CDROMBoot Other Device Default Enabled Swap Floppy Drive Default DisabledTypematic Delay Msec Default Security Option Default SetupApic Mode Default Enabled MPS Version Control For OS DefaultThermal Management Default Thermal Monitor TM2 Bus Ratio Default 0TM2 Bus VID Default Advanced Chipset Features Performance Mode Default Disabled Dram Timing control Default By SPDDram CAS Latency Default 2.5T RAS Active Time tRAS Default 6TAGP Aperture Size Default 64 MB Graphic Window WR Combin Default DisabledAGP Fast Write Support Default Enabled AGP Data Rate Default AutoVGA Share Memory Size Default 32 MB Graphics Engin Clock Default 133 MHzIntegrated Peripherals Audio Access Interface Default EDB Bus Internal PCI/IDE Default BothIDE Primary/ Secondary Master/Slave PIO Default Auto Primary/Secondary Master/Slave UltraDMA Default AutoSIS USB Controller Default Enabled USB Ports Number Default 6 portsUSB 2.0 Supports Default Enabled USB Keyboard Support Default EnabledOnboard FDC Controller Default Enabled Onboard Serial Port1/2 Default 3F8/IRQ4 / 2F8/IRQ3Uart Mode Select Default Normal UR2 Duplex Mode Default HalfPower Management Setup Acpi function Default EnabledAcpi Suspend Type Default S1POS Power Management Default User DefineVideo Off Option Default Susp, Stby off Video Off Method Default Dpms SupportedSwitch Function Default Break/Wake Modem Use IRQ Default AutoIRQ 3-7,9-15, NMI Default Enabled IRQ 8 Break Suspend Default DisabledRing Power Up Control Default Enabled Macpme Power Up Control Default EnabledMonth Alarm Day of Month AlarmTime hhmmss Alarm Primary/Secondary IDE Default DisabledPnP/PCI Configurations Reset Configuration Data Default DisabledResources Controlled By Default AutoESCD PCI/VGA Palette Snoop Default DisabledPC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Password Enter PasswordSave & Exit Setup Exit Without SavingSave to Cmos and Exit Y/N?Y Quit Without Saving Y/N?NChapter Utility CD content Install DriverAccessories Browse CDStart to Install divers Install IDE DriverInstall AGP Driver Install VGA DriverInstall DirectX Install USB 2.0 Driver Using 4-/6-Channel AudioInstalling the Audio Driver Attaching Speakers Channel Analog Audio OutputLine-out Rear channels Line-out Front channels Microphone Selecting 4- or 6-Channel Setting Digital Audio OutputClick the Speaker Configuration tab Testing Each Speaker Playing KaraokeInstall LAN Driver Install Norton Internet Security Directions for Bundled Software SuperStep features Using SuperStepDirections for Bundled Software Directions for Bundled Software SuperLogo features Using SuperLogoDirections for Bundled Software SuperUpdate features Using SuperUpdateDirections for Bundled Software Backup Bios to local image Directions for Bundled Software Directions for Bundled Software Update Bios On-line Click OK to update Bios Click Restart Special Bios Functions SuperSpeed SuperBoot SuperBIOS-Protect SuperRecovery Hotkey SelectionHard Disk Selection What is a Hidden Partition? Main MenuDivide Hidden Partition Divide Hidden PartitionRelease Hidden Partition Backup Backup Cmos SetupBackup Partition Table Backup Hard disk Data Recovery Back to MainRecover Cmos Setup Recover Partition TableChange Password Introduction Recover Hard disk Data