Foxconn 661M03 user manual Directions for Bundled Software

Page 83

Chapter 5 Directions for Bundled Software

Adjust voltage warning

Go to Voltage page criteria (upper limit)

Current voltage readings

Reset the warning	Apply the	Adjust voltage
criteria to default	adjustments	warning criteria
settings		(lower limit)

Go to Temperature page

Current CPU								Adjust CPU tem-
temperature								perature warning
temperature								perature warning
Current system								criteria
Current system
temperature								Adjust system
temperature								Adjust system
								temperature
								temperature
								warning criteria
		Reset the warning
		Reset the warning	Apply the adjustments
		criteria to default
		settings

		75
	661M03 Series User Manual	75
	661M03 Series User Manual

Image 83

Contents Version Item Checklist Declaration of conformity HON HAI Precision Industry Table of Contents Chapter Directions for Bundled Software Chapter Special Bios FunctionsChapter Driver CD Introduction Page Page Page Main Features Onboard Graphics Onboard 1394 optionalOnboard LAN Onboard I/OGreen Function Advanced FeaturesMotherboard Layout AGP slot ATX 12V connectorATX power connector PHY optionalSouth Bridge controller Floppy disk connectorIDE connectors Flash RomInstallation Instructions Installation Instructions CPU Installation of CPUInstallation of CPU Fan Installation Instructions Frequence CPU Qualified Vendor ListVendor Type Memory Installation of DDR MemoryVender Type Size Memory Qualified Vendor ListChapter Installation Instructions Pin ATX12V Power Connector PWR2 Power SupplyPin ATX power connector PWR1 This motherboard provides the ports as below Rear Panel ConnectorsLine-in Line-out Front channels Microphone HDD connectors IDE1 & IDE2 Other ConnectorsFDD Connector Front Panel Connector FP1 USB Headers Fusb IrDA Header IR optionalAudio Connectors Cdin Fan Connectors CPUFAN, FAN1Wake-Up On LAN WOL Header F1394 optionalAudio Interface Faudio Pdif Out Connector SpdoutAGP Slot Expension SlotsPCI Slots Vender Type Video Memory Installing an expansion cardAGP Qualified Vendor List CNR Slot optional Clear Cmos Jumper Clscmos JumpersDescription of Jumpers CNR Audio Selection Jumper J24 BIOS-Protection Jumper FwhenStarting up for the first time Powering off the computerBios Description Bios Features Enter Bios SetupPress TAB to show Post screen, DEL to enter Setup Standard Cmos FeaturesPnP/PCI Configurations Advanced Bios FeaturesAdvanced Chipset Features Power Management SetupIDE Primary/Secondary Master/Slave Standard Cmos FeaturesDate TimeHalt On Drive A/BVideo Memory SuperBoot SuperBoot Default Disabled Bios FeaturesAdvanced Bios Features Swap Floppy Drive Default Disabled Quick Power On Self Test Default EnabledFirst/Second/Third Boot Device Default Floppy/HDD- 0/CDROM Boot Other Device Default EnabledMPS Version Control For OS Default Typematic Delay Msec DefaultSecurity Option Default Setup Apic Mode Default EnabledTM2 Bus VID Default Thermal Management Default Thermal MonitorTM2 Bus Ratio Default 0 Advanced Chipset Features RAS Active Time tRAS Default 6T Performance Mode Default DisabledDram Timing control Default By SPD Dram CAS Latency Default 2.5TAGP Data Rate Default Auto AGP Aperture Size Default 64 MBGraphic Window WR Combin Default Disabled AGP Fast Write Support Default EnabledGraphics Engin Clock Default 133 MHz VGA Share Memory Size Default 32 MBIntegrated Peripherals Primary/Secondary Master/Slave UltraDMA Default Auto Audio Access Interface Default EDB BusInternal PCI/IDE Default Both IDE Primary/ Secondary Master/Slave PIO Default AutoUSB Keyboard Support Default Enabled SIS USB Controller Default EnabledUSB Ports Number Default 6 ports USB 2.0 Supports Default EnabledUR2 Duplex Mode Default Half Onboard FDC Controller Default EnabledOnboard Serial Port1/2 Default 3F8/IRQ4 / 2F8/IRQ3 Uart Mode Select Default NormalPower Management Default User Define Power Management SetupAcpi function Default Enabled Acpi Suspend Type Default S1POSModem Use IRQ Default Auto Video Off Option Default Susp, Stby offVideo Off Method Default Dpms Supported Switch Function Default Break/WakeMacpme Power Up Control Default Enabled IRQ 3-7,9-15, NMI Default EnabledIRQ 8 Break Suspend Default Disabled Ring Power Up Control Default EnabledPrimary/Secondary IDE Default Disabled Month AlarmDay of Month Alarm Time hhmmss AlarmPCI/VGA Palette Snoop Default Disabled PnP/PCI ConfigurationsReset Configuration Data Default Disabled Resources Controlled By Default AutoESCDPC Health Status Frequency/Voltage Control Enter Password Load Fail-Safe DefaultsLoad Optimized Defaults Set PasswordQuit Without Saving Y/N?N Save & Exit SetupExit Without Saving Save to Cmos and Exit Y/N?YChapter Browse CD Utility CD contentInstall Driver AccessoriesInstall IDE Driver Start to Install diversInstall VGA Driver Install AGP DriverInstall DirectX Installing the Audio Driver Install USB 2.0 DriverUsing 4-/6-Channel Audio Channel Analog Audio Output Attaching SpeakersLine-out Rear channels Line-out Front channels Microphone Digital Audio Output Selecting 4- or 6-Channel SettingClick the Speaker Configuration tab Playing Karaoke Testing Each SpeakerInstall LAN Driver Install Norton Internet Security Directions for Bundled Software Using SuperStep SuperStep featuresDirections for Bundled Software Directions for Bundled Software Using SuperLogo SuperLogo featuresDirections for Bundled Software Using SuperUpdate SuperUpdate featuresDirections for Bundled Software Backup Bios to local image Directions for Bundled Software Directions for Bundled Software Update Bios On-line Click OK to update Bios Click Restart Special Bios Functions SuperSpeed SuperBoot SuperBIOS-Protect Hotkey Selection SuperRecoveryHard Disk Selection Divide Hidden Partition What is a Hidden Partition?Main Menu Divide Hidden PartitionRelease Hidden Partition Backup Partition Table BackupBackup Cmos Setup Backup Hard disk Data Back to Main RecoveryRecover Partition Table Recover Cmos SetupRecover Hard disk Data Change Password Introduction