ETA Systems ETA-20SH specifications Safety Instructions

Page 5

ETA-20SH

AC Power Conditioning & Suppression Module

SAFETY INSTRUCTIONS

 

CAUTION

 

RISK OF ELECTRIC SHOCK

 

DO NOT OPEN

ATTENTION

´

-NE PAS OUVRIR.

 

RISQUE DE DECHARGE ELECTRIQUE

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this device near water.

6.Clean only with dry cloth.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage “ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other device (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the device.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the device. When a cart is used use caution when moving the cart/device combination to avoid injury from tip-over.

13.This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

14.Unplug this device during lightning storms or when unused for long periods of time.

15.Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled, objects have fallen into the device, the device has been exposed to rain or moisture, does not operate normally, or has been dropped.

16.To prevent fire or shock hazard. Do not expose this appliance to rain or moisture.

This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such as vases shall be placed on apparatus.

17.To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle.

18.The mains plug of the power supply cord shall remain readily operable.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: 800-321-6699 • Fax: 800-996-3821

– 5 –

ETAsys.com

Specifications are subject to change without notice.

Image 5
Contents ETA-20SH Table of Contents AC Power Conditioning & Suppression ModuleApplications KEY FeaturesIntroduction ETA-20SH Safety Instructions AC Spike Protection EMI/RFI FiltersAC Surge Protection EVS ProtectionAC Mains Power Cord 9 3m, 12-gauge Panel FeaturesUsing the ETA-20SH AS a Standalone Unit ECM Data Wire and DistanceRemote Activation VIA Switch or DCV Trigger Wiring with AN ETA-ECS6RM Sequencer ControllerRelay Contacts ETA-ECS6RM Sequencer Controller Interface with ETA-20SHSingle ETA-ECM20 Control Port Wiring With an ETA-ECS3 Sequencer Controller Troubleshooting the ECM Module AS a Standalone Unit Troubleshooting the ECM Module with AN ETA-ECS3 Issue 1 Incoming AC LED on the ECM is not illuminated Troubleshooting the ECM Module with AN ETA-ECS6RMIssue 6 No Voltage Reading at the ETA-ECS6RM ETA-20SH Specifications Service Limited Warranty