Eurotech Appliances COM-1460 user manual Safety Summary

Page 29

PC/104-PlusCOM-1460 Module

29

 

 

 

 

A.2 Safety Summary

The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the equipment. Eurotech SpA assumes no liability for the customer’s failure to comply with these requirements.

The safety precautions listed below represent warnings of certain dangers of which Eurotech is aware. You, as the user of the product, should follow these warnings and all other safety precautions necessary for the safe operation of the equipment in your operating environment.

Ground the Instrument

To minimize shock hazard, the equipment chassis and enclosure must be connected to an electrical ground. The equipment is supplied with a three-conductor ac power cable; the power cable must be plugged into an approved three-contact electrical outlet, with the grounding wire (green) firmly connected to an electrical ground (safety ground) at the power outlet. The power jack and mating plug of the power cable meet International Electro technical Commission QEC) safety standards.

Do Not Operate in an Explosive Atmosphere

Do not operate the equipment in the presence of flammable gases or fumes. Operation of any electrical equipment in such an environment constitutes a definite safety hazard.

Keep Away From Live Circuits

Operating personnel must not remove equipment covers. Only Factory Authorized Service Personnel or other qualified maintenance personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment. Do not replace components with power cable connected. Under certain conditions, dangerous voltages may exist even with the power cable removed. To avoid injuries, always disconnect power and discharge circuits before touching them.

Use Caution When Exposing or Handling the CRT

Breakage of the Cathode-Ray Tube (CRT) causes a high-velocity scattering of glass fragments (implosion). To prevent CRT implosion, avoid rough handling or jarring of the equipment. Only qualified maintenance personnel using approved safety mask and gloves should handle the CRT.

Do Not Substitute Parts or Modify Equipment

Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modification of the equipment. Contact Eurotech technical staff or your local representative for service and repair to ensure that safety features are maintained.

Observe Dangerous Procedure Warnings

Warnings, such as the example below, precede potentially dangerous procedures throughout this manual. Instructions contained in the warnings must be followed. You should also employ all other safety precautions, which you deem necessary for the operation of the equipment in your operating environment.

Flammability

All Eurotech PWBs (printed wiring boards) are manufactured by UL-recognized manufacturers, with a flammability rating of UL-V0.

Image 29
Contents COM-1460 About this Manual Conventions This page is intentionally left blank Contents Glossary Acronyms and Abbreviations Product Overview Product Definition COM-1460 PC/104-Plus Module characteristicsCOM-1460 module’s functional blocks Jumper Description = Open Jumper Layout and ConfigurationJP3 JP1JP2 This page is intentionally left blank Connectors Description PCI BUS Connectors LayoutPCI BUS J1, J2 for the ISA Bus and J3 for the PCI BusISA BUS Module Stack J10 for Main Power J7, J8, J9 for FirewireThis page is intentionally left blank Troubleshooting Technical/Sales Assistance Common Problems and SolutionsTroubleshooting a PC/104-Plus System Returning For Service This page is intentionally left blank RMA This page is intentionally left blank Appendix Absolute Maximum Ratings Electrical and Environmental SpecificationsOperating Characteristics Mtbf Module Dimensions Mechanical DimensionsSafety Summary EMI Caution Disclaimer of WarrantyCE Notice ReliabilityGlossary BiosATA AtapiCvbs CPUDMA DeviceIDE HDCIeee IRQNdis MpegNMI NtscROM RAMScsi SecamThis page is intentionally left blank Scsi Acronyms and AbbreviationsTechnical & Sales Assistance