Dell E5530 owner manual Working on Your Computer, Before Working Inside Your Computer

Page 5

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist:

You have read the safety information that shipped with your computer.

A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse order.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface, such as a connector on the back of the computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in this document. To avoid damaging your computer, perform the following steps before you begin working inside the computer.

1.Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2.Turn off your computer (see Turning Off Your Computer).

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.

3.Disconnect all network cables from the computer.

4.Disconnect your computer and all attached devices from their electrical outlets.

5.Press and hold the power button while the computer is unplugged to ground the system board.

6.Remove the cover.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.

5

Image 5
Contents Regulatory Model P28G Regulatory Type P28G001 Contents Docking Port Information Specifications Diagnostics Before Working Inside Your Computer Working on Your ComputerAfter Working Inside Your Computer Turning Off Your ComputerRemoving the Battery Installing the SD Memory CardRecommended Tools Removing the SD Memory CardRemoving the Subscriber Identity Module SIM Card Installing the BatteryInstalling the Subscriber Identity Module SIM Card Removing the Camera Installing the Display BezelRemoving the Display Bezel Removing the Display Panel Installing the CameraPage Removing the Keyboard Trim Installing the Display PanelPage Removing the Keyboard Installing the Keyboard TrimPage Page Removing the Access Panel Installing the KeyboardRemoving the Optical Drive Installing the Access PanelPage Removing The Hard Drive Installing the Optical DrivePage Installing the Hard Drive Installing the Wireless Local Area Network Wlan Card Removing the Wireless Local Area Network Wlan CardInstalling the Memory Module Removing the Memory ModuleRemoving the Right Base Panel Installing the Right Base PanelRemoving the Thermal Module Installing the Thermal ModuleRemoving the Palmrest Installing the ProcessorRemoving the Processor Page Installing the Palmrest Removing the ExpressCard Reader Cage Installing the ExpressCard Reader CageRemoving the Audio Board Removing the Bluetooth ModuleInstalling the Bluetooth module Removing the Display Assembly Installing the Audio BoardPage Page Removing the Right Support Frame Installing the Display AssemblyRemoving the Modem Card Installing the Right Support FrameRemoving the Left Support Frame Installing the Modem CardRemoving the System Board Installing the Left Support FramePage Page Removing the Coin-Cell Battery Installing the System BoardRemoving the Input/Output I/O Board Installing the Coin-Cell BatteryInstalling the Input/Output I/O Board Removing the Power Connector Removing the System Fan Installing the Power ConnectorPage Removing the Network Connector Installing the System FanRemoving the Speakers Installing the Network Connector JackInstalling the Speakers Follow the procedures in After Working Inside Your Computer Page Docking Port Information Page Specifications SpecificationsInterface Internal High definition audio External Display Feature Specifcation Feature Environmental Overview Entering System SetupSystem Setup Options Uefi ATA Option Description You can also enable or disable Media Card Admin password Default Setting Enable Intel SpeedStep Custom Charge Stop Wwan System Logs Page Diagnostics DiagnosticsPage Contacting Dell Contacting Dell
Related manuals
Manual 8 pages 36.57 Kb