Diamond Systems PR-Z16-LC-ST user manual Bios Features, Bios Settings

Page 20

7. BIOS FEATURES

7.1BIOS Settings

Prometheus-LC uses a BIOS from Phoenix Technologies modified to support the custom features of the ZF Micro ZFx86 chip and the Prometheus-LC board. Some of these features are described here.

To enter the BIOS during system startup (POST – power on self-test), press F2.

Serial Ports

-The address and interrupt settings for serial ports COM1 – COM4 may be modified. COM1 and COM2 address and interrupt settings are done in the BIOS, Advanced menu, I/O Device Configuration. See page 24 for details.

-The addresses of COM3 and COM4 are configurable in the BIOS. Select Advanced menu, Advanced Chipset Control, ISA I/O Chip Select Setup. See page 24 for details.

Parallel Port

-The parallel port settings may be modified on the same screen as serial ports COM1 and COM2 (I/O Device Configuration).

Data Acquisition

-The on-board data acquisition circuit is modified on the same screen as serial ports COM3 and COM4 (ISA I/O Chip Select Setup).

Floppy / IDE Settings

-On the Advanced screen, I/O Device Configuration, the following settings should be retained:

Floppy disk controller

Enabled

Base I/O address

Primary

Local Bus IDE adapter

Primary

Miscellaneous

-On the Advanced screen, the following settings should be retained:

USB Host Controller

Enabled

USB BIOS Legacy Support

Disabled (Legacy support is not currently provided)

Installed O/S

Other

Large Disk Access Mode

DOS

Remote Management Baud Rate

Ignore; feature not supported on Prometheus

-On the PCI Configuration page (from the Advanced screen), the following setting should be retained:

ISA Graphics Device Installed

No

PCI IRQ Level 1-4

Autoselect for all

PCI/PNP ISA UMB Region Exclusion Available for all

-The features on the Power screen are not supported on Prometheus.

Prometheus-LC CPU User Manual V1.0

Page 20

Image 20
Contents PROMETHEUS-LC Table of Contents 12.1 12.212.3 12.4Description Processor Section FeaturesSystem Features PROMETHEUS-LC Board Drawing J4 Not presentMain I/O Connector J3 O HeadersCable a Cable BConnector Part Numbers COM1 COM4Input Power J11 Output Power J12 USB J5Auxiliary Serial Port Connector J15 Watchdog/Failsafe Features J6Floppy Drive J7 IDE Drive J8PC/104 Bus Connectors J2 PC/104 16-bit bus connector J1 PC/104 8-bit bus connectorJumper Configuration System Configuration J10Watchdog Timer & System Recovery J6 CPU Chip Selects System FeaturesSystem Resources Console Redirection to a Serial Port Watchdog Timer Failsafe Mode / Bios Recovery Backup BatterySystem Reset Flash MemoryBios Features Bios SettingsBios Download / Recovery GroundOperating System Formatting Initial SetupDISK-ON-BOARD Flash File Storage Known Limitations Life Cycle Management and CalculationsParallel Port System I/OSerial Ports Installing an OS From a Floppy Drive onto a Flashdisk Module Installing an OS from a Hard Disk onto a Flashdisk Module Configuration Using the Flashdisk with Another IDE DrivePower Supply Flashdisk Module12. I/O Panel Board DescriptionPanel Board I/O Connectors Panel Board Top Side / External Use I/O ConnectorsLocation Type Description Panel Board HardwarePanel Board Power Connections J12 pinout to/from DC/DC power supplyJ3 Pinout J9 Pinout Installation J5 USBFlash Disk Programmer Board Cable Kit C-PRZ-KIT 14.I/O CablesPhoto No Cable No Description PL5 pin no DB15F pin no Signal VGA Accessory BoardPL5 pin no PL5 Signal J25 pin no J25 Signal Website information Connector on Board Manufacturer Manufacturer Part NoMounting PROMETHEUS-LC on a Baseboard Page 17.PC/104 Mechanical Drawing

Low-Power PC/104 CPU Board With ZFx86 Processor, PR-Z16-LC-ST specifications

The Diamond Systems Low-Power PC/104 CPU Board featuring the ZFx86 Processor, specifically the PR-Z16-LC-ST model, represents a significant advancement in embedded computing technology. This CPU board is designed to deliver robust performance while maintaining low power consumption, making it ideal for a wide array of industrial and embedded applications.

One of the standout features of the PR-Z16-LC-ST board is its ZFx86 Processor. This processor family is built with a focus on energy efficiency and low thermal output, which is crucial for applications where heat dissipation can be a challenge. The ZFx86 provides an excellent balance between processing power and energy consumption, featuring a 16-bit instruction set that facilitates compatibility with many existing software applications.

This board supports a variety of operating environments, including DOS, Linux, and Windows, ensuring versatility for developers. Its design includes a compact PC/104 form factor, which allows for streamlined stacking of multiple boards. This modularity is beneficial for system integrators looking to create customized solutions with limited space.

In terms of connectivity, the PR-Z16-LC-ST is equipped with a wide range of I/O ports. This includes digital and analog inputs and outputs, serial communication ports, and support for various peripheral devices. Such features make it a suitable choice for tasks such as data acquisition, control systems, and automation processes.

Additionally, the Diamond Systems board is designed with an onboard memory expansion capability, allowing users to enhance performance based on specific application needs. The support for both DRAM and flash memory options provides flexibility in memory configuration.

The board also emphasizes reliability and longevity, with rugged construction suitable for harsh environments. This durability is essential for applications in sectors such as transportation, telecommunications, and factory automation, where systems must withstand extreme conditions.

In summary, the Diamond Systems PR-Z16-LC-ST Low-Power PC/104 CPU Board with ZFx86 Processor combines efficiency with a robust feature set. Its low power consumption, modular design, and extensive connectivity options make it an attractive solution for developers in the embedded computing space seeking reliable performance in compact configurations.