Cobalt Networks PS-8300 user manual Product Power Cord Requirements, EMC Notices, US FCC Part

Page 5

Product Power Cord Requirements

Warning

Warning

North American Line Voltages 100 - 120 Volts

This product is supplied with certified 10A/125V SVT type supply cords.

Conductors are color coded white (neutral), black (line) and green or green/yellow (ground).

Operation of this equipment at line voltages exceeding 130V requires that alternative supply cords with appropriate voltage and current ratings be used

International Line Voltages 200 - 240 Volts

This product has been designed for use with certified IEC 320- C13 10A/250V - H03 VV-F3G 1.00mm2 type line cord.

International product orders are supplied with a certified 10A/250V line cords, utilizing a molded 3-pin IEC 320-C13 type connector at one end and stripped conductors on the other. One line cord is provided. Conductors are CEE color coded; blue (neutral), brown (line), and green/yellow (ground).

Installation by a qualified Electrician, of an appropriately approved A/C wall plug certified for the country of use, is required.

Alternatively, other IEC 320 C-13 type power cords may be used, provided that they meet the necessary safety certification requirements for the country in which they are to be used. Refer to the correctly specified line cord above.

EMC Notices

US FCC Part 15

This equipment has been tested and found to comply with the limits for a class A Digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense.

Changes or modifications to this equipment not expressly approved by Cobalt Digital Inc. could void the user’s authority to operate this equipment.

Notice

CANADA

This Class “A” digital apparatus complies with Canadian ICES-003.

EUROPE

This equipment is in compliance with the essential requirements and other relevant provisions of CE Directive 93/68/EEC.

INTERNATIONAL

This equipment has been tested to CISPR 22:1997 along with amendments A1:2000 and A2:2002 and found to comply with the limits for a Class A Digital device.

This is a Class A product. In domestic environments this product may cause radio interference in which case the user may have to take adequate measures.

Notice

8310 User Manual (V 1.0.1)

Page 5 of 40

Image 5
Contents Cobalt Digital Inc OpenGearTM Two Rack Unit Frame Power Supply PS-8300Trademarks CopyrightSymbol Meanings Important Regulatory and Safety NoticesImportant Safety Instructions US FCC Part Product Power Cord RequirementsEMC Notices Environmental Information Maintenance/User Serviceable PartsContents Contact Us Service InformationOrdering Information This Chapter IntroductionWord of Thanks OverviewRobust Power Supplies FeaturesDocumentation Terms Unpacking Installation and SetupStatic Discharge Power Supply PS-8300 and Power Cable Installing the FrameInstalling the Frame Power Supply Hazardous VoltagesImproving Performance Fault ReportingVentilation and Cooling Color Display and DescriptionPower Cable Connection Fan Kit InstalledCable Connections Without Fan KitBNC Rear I/O Module Rear I/O ModulesSmpte Alarm Connector Rear I/O Module InstallationDual Reference Connectors OpenBUS ConnectorEthernet Connector Smpte 269M Fault Reporting Option Details Frame ConnectionsTechnical Specifications SpecificationsEnvironmental Smpte FaultReporting Important Notes Frame Features Fan Board Installation Instructions Cooling FeaturesInstalling the Cooling Fan Module Cooling Fan Functions and User Controls Frame Door FeaturesFunctions of the Controller Card Installing the Controller CardAlarm Mute Button MFC-8310 Alarm Configuration JumperControls and LEDs for the Controller Card MFC-8310 LEDsMFC-8310 Controller Card LED Descriptions Installing the Network Controller Card Remote Control Networking FeaturesEthernet Setup Functions of the Network Controller CardControls and LEDs for the Network Controller Card MFC-8310-N DIP SwitchesMFC-8310-N LEDs DIP Switches on the MFC-8310-NButtons on the MFC-8310-N Color Location Display and Description DashBoard and DashBoard Lite Control System SoftwareSnmp Monitoring and Control Operating Tip Configuring SnmpEnabling Snmp Rear Support Bars and Brackets Installing the Rear Support Bars and BracketsFrame Controller Alarm Mute/Bootload Button Service InformationTroubleshooting Checklist Case of Problems Warranty and Repair PolicyOptional Equipment Ordering InformationStandard Equipment Page Visit us at the Cobalt Digital Inc. website Contact UsContact Cobalt Digital Inc