ArtDio IPS 1000 user manual Dhcp Mode, PPPoE Mode

Page 17

IPS 1000 Series VoIP Gateway

9.2.2.DHCP Mode

1.Connect the IPS unit to a suitable Power source.

2.Connect a traditional phone set to the “FXS” connector located on the rear panel.

3.When the CPU/ACT light is on, pick up the phone to hear the dialing tone.

4.

##0000

; you should hear three short tones.

5.

011#

; the digit “1” is used to enable “DHCP” IP mode.

6.

15123#

; “123” is the web management password.

7.

981#

; Warm-restarts.

8.

Hang up the phone. The system should now restart.

You can also use console to configure IP address. But phone number can’t be configured by console.(Only for 4 ports gateway)

SIP-RG>enable SIP-RG#configure

Enter configuration commands, one per line. End with CNTL/Z SIP-RG(config)#ip state dhcp

SIP-RG(config)#exit SIP-RG#restart

This command resets the system. System will restart operation code agent. Reset system, [Y]es or [N]o? Yes

9.2.3.PPPoE Mode

If your network environment is using PPPoE, you need to prepare the information as specified in section

8.Information required before Installation. The following table shows an example.

PPPoE Account

83721@hinet.net

 

 

PPPoE Password

123ab

 

 

Web management password

123

 

 

There are three ways to configure user name and password of PPPoE

1. Use phone set to configure:

You can configure the user name and password by using phone set. The command ‘09’ is used for username and ‘10’ is for password of PPPoE. Since the user name and password use characters and

17

Image 17
Contents ARTDio Company Inc Version3.1 Update2004/5/7IPS 1000 Series Contents SIP Outbound Authentication IP SettingFAX WEB Management InterfacePreface Safety InstructionsWhat is SIP Components of SIP IPS 1000 Series VoIP Gateway Architecture Panel Descriptions Package ContentsRear Panel IPS 1103 Rear Panel 4 ports IPS 1101 Rear Panel 2 ports LED Indicators IDC Connectors Only for IPS-1000 series 8/16 ports ConnectorsIP Address Information required before InstallationSIP Information Prepare a password for Web ManagementConfirming the Region ID Installation and ConfigurationPhone Setting System console settings Only for 4/8/16 ports IP Address SettingsStatic IP Mode PPPoE Mode Dhcp ModeUse WEB Interface to configure IPS 1000 Series VoIP Gateway Mosa WEBUpon entering the web based configuration interface IPS 1000 Series VoIP Gateway SIP Configuration IPS-1008 Channels and SIP entitySIP Entity SIP Proxy and Register ParametersSIP Outbound Authentication Configure Stun Phone Book Check SIP entity StatusMake SIP Calls Contact Address FXO FXS Other SIP ParametersDialing Plan Call Forward Inbound AuthenticationDevices at two sides are IPS 1000 and the other brands FAXDevices at two sides are all IPS 1000 series gateway Authentication Home Basic General IP Setting AdvancedChannel Phone Book Access Code SIP OutboundBasic / General OFF MACIPS RTPISP IP SettingWEB Dtmf Advanced / GeneralCadence On, off. The on and off SIP Common CMU-PCMA PcmuPcma RFC 2833 Dtmf SIP Outbound Authentication SIP Inbound Anthentication Dialing Plan Dialing Plan Stun Channel IPS 1000 Series VoIP Gateway Phone Book Use Private IP Behind NAT DND Appendix a Phone-Set CommandAppendix IPS 1000 Series VoIP Gateway Enable Appendix B Console CommandVAD, CNG SpecificationsRTP, Rtcp EMIMapping table of characters used in PPPoE USA Region IDTaiwan Contact Information