Delta Tau PMAC2A-PC/104 manual ACC-2P Hardware Reference Summary, Board Dimensions

Page 43

PMAC2A PC104 Hardware Reference Manual

ACC-2P HARDWARE REFERENCE SUMMARY

The following information is based on the Acc-2P board, part number 603672-100.

Board Dimensions

Acc-2P Hardware Reference Summary

37

Image 43

Contents PMAC2A-PC/104 Delta Tau Data Systems, Inc. Technical Support Copyright InformationTable of Contents Software Setup Base Board Connector Pinouts PMAC2A PC104 Hardware Reference Manual Table of Contents Introduction Board ConfigurationAcc-1P Option 2 Analog-to-Digital Converters Option 12 Analog-to-Digital ConvertersAcc-1P Axis Expansion Piggyback Board Acc-1P Option 1 I/O PortsAcc-2P Option 2 Dpram Circuitry Acc-2P Communications BoardAcc-2P Option 1A USB Interface Acc-2P Option 1B Ethernet InterfacePMAC2A PC104 Hardware Reference Manual Introduction Clock Configuration Jumpers Base Board Hardware SetupBoard Reset Jumpers Communication Jumpers CPU Jumper ConfigurationConfiguration Jumpers Resistor Packs ConfigurationDevice Resistor Pack Pack Size PMAC2A PC104 Hardware Reference Manual Reserved Configuration Jumpers ACC-1P Hardware SetupE0 Reserved for future use Handwheel Encoder Termination Resistors Jthw Connector DATx SELx ACC-2P Hardware SetupJopt Connector E10 MOx MIx Lines Differential or Single-Ended Handwheel Encoder Selection Machine Connections Power SuppliesDigital Power Supply DAC Outputs Power SupplyMotor Signals Connections Overtravel Limits and Home SwitchesExample DAC Output SignalsAmplifier Enable Signal AENAx/DIRn Pulse and Direction Stepper DriversAcc-1P General-Purpose Digital Inputs and Outputs J7 Port Amplifier Fault Signal FaultAcc-1P Thumbwheel Multiplexer Port J2 Port Acc-2P General-Purpose Digital Inputs and Outputs Jopt PortAcc-2P Thumbwheel Multiplexer Port Jthw Port Optional Analog Inputs Acc-1P or Acc-2P Handwheel Port JHW / PD PortCompare Equal Outputs PC DB-9 Acc-2P Ethernet RJ45 Connector J10 PortAcc-2P USB Connector J1 Port Serial Port JRS232 PortMachine Connections Example Using Analog ±10V Amplifier PMAC2A PC104 Hardware Reference Manual PMAC2A PC104 Hardware Reference Manual Machine Connections Pmac I-Variables Software SetupOperational Frequency and Baud Rate Setup CommunicationsI54 Baud Rate Filtered DAC Outputs ConfigurationI54 Baud Rate for Flag Type Channel Number Using Flag I/O as General-Purpose I/OGeneral-Purpose Digital Inputs and Outputs Acc-1P with Jumper E6 on PositionOpen PLC1 Clear Acc-2P with Jumper E5 in PositionAcc-1P with Jumper E6 in Position Thumbwheel Port Digital Inputs and OutputsBaseboard Analog Inputs Analog Inputs SetupAcc-1P Analog Inputs Base Board Hardware Reference Summary Board DimensionsFeature Location FeatureBoard Layout Connectors and Indicators Page ACC-1P Hardware Reference Summary TB1 JMACH1 J7 General-Purpose Digital Inputs and Outputs Jopt Port J2 Thumbwheel Multiplexer Port Jthw PortJ8 Handwheel / Pulse and Direction Port JHW / PD Port Page ACC-2P Hardware Reference Summary TB1 Jthw Jopt J8 Handwheel/Pulse and Direction Port JHW / PD Port J1 USB Communications PortJ10 Ethernet Communications Port Page Base Board E-POINT Jumper Descriptions E0 Forced Reset ControlE1 Servo and Phase Clock Direction Control E3 Normal/Re-Initializing Power-Up/ResetDescription Default E8 Phase Clock Lines Output EnableE9 Servo Clock Lines Output Enable E10 E12 Power-Up State JumpersE15A, B, C Flash Memory Bank Select E13 Power-Up/Reset Load SourceE14 Watchdog Disable Jumper E16 ADC Inputs EnableE18 E19 PC/104 Bus Address Point and Physical Location Description Default LayoutE3 E4 JHW, PD Function Select E1 E2 Machine Output Supply Voltage ConfigureACC-1P E-POINT Jumper Descriptions E0 Reserved for Future UseE6 I/O Gate Address Select E5 Servo Gate Address SelectE7 Machine Input Source/Sink Control E6 Communications Port Select E1 USB/Ethernet Micro-Controller Firmware Reload EnableACC-2P E-POINT Jumper Descriptions E5 I/O Gate Address SelectE7- E10 Ports Direction Control Point and Physical Location Description DefaultPin# Symbol Function Description Base Board Connector PinoutsTB1 Jpwr Power Supply J4 JRS232 Serial Port ConnectorJ3 JMACH1 Machine Port Connector J3 JMACH1 50-Pin Header J4 JMACH2 Machine Port Baseboard Connector ACC-1P Connector Pinouts Pin# Symbol J2 Jthw Multiplexer Port ConnectorJ3 JMACH1 Machine Port Connector Pin Header J3 JMACH1 50-Pin-Header FLG78V Connector 34-Pin HeaderJ7 Jopto I/O Port Connector J8 JHW Handwheel Encoder Connector Page Pin # Symbol Function ACC-2P Connector PinoutsJ1 USB Universal Serial Bus Port Optional Pin Connector J7 Jopt I/O Port Connector Pin # Function J10 Ethernet Port Optional