Delta Tau PMAC2A-PC/104 manual J1 USB Communications Port, J10 Ethernet Communications Port

Page 45

PMAC2A PC104 Hardware Reference Manual

Connectors and Indicators

J1 – USB Communications Port

This connector provides access to the USB communications feature ordered through Option-1A. See the Machine Connections section for details on using this port.

J2 - Thumbwheel Multiplexer Port (JTHW Port)

The Thumbwheel Multiplexer Port, or Multiplexer Port, on the JTHW connector has eight input lines and eight output lines. The output lines can be used to multiplex large numbers of inputs and outputs on the port, and Delta Tau provides accessory boards and software structures (special M-variable definitions) to capitalize on this feature. Up to 32 of the multiplexed I/O boards may be daisy-chained on the port, in any combination.

1.26-pin female flat cable connector T&B Ansley P/N 609-2641

2.Standard flat cable stranded 26-wire T&B Ansley P/N 171.26

3.Phoenix varioface module type FLKM 26 (male pins) P/N 22 81 05 0

J7 - General-Purpose Digital Inputs and Outputs (JOPT Port)

Acc-2P’s JOPT connector provides eight general-purpose digital inputs and eight general-purpose digital outputs. Each input and each output has its own corresponding ground pin in the opposite row. The 34- pin connector was designed for easy interface to OPTO-22 or equivalent optically isolated I/O modules. Delta Tau’s Acc-21F is a six-foot cable for this purpose.

1.34-pin female flat cable connector T&B Ansley P/N 609-3441

2.Standard flat cable stranded 34-wire T&B Ansley P/N 171-34

3.Phoenix varioface module type FLKM 34 (male pins) P/N 22 81 06 3

J8 – Handwheel/Pulse and Direction Port (JHW / PD Port)

This port provides an extra encoder input or a set of pulse and direction outputs and its function is selectable by jumpers.

1.10-pin female flat cable connector T&B Ansley P/N 609-1041

2.Standard flat cable stranded 10-wire T&B Ansley P/N 171-10

3.Phoenix varioface module type FLKM 10 (male pins) P/N 22 81 01 8

J10 – Ethernet Communications Port

This connector provides access to the Ethernet communications feature ordered through Option-1B. See the Machine Connections chapter for details on using this port.

TB1 – Power Supply Terminal Block (JPWR Connector)

In almost in all cases the PMAC2A PC/104 will be powered from the PC/104 bus when it is installed in a host computer’s bus, or from the JMACH1 connector. This terminal block may be used as an alternative power supply connector or to easily measure the voltages applied to the board.

1. 4-pin terminal block, 0.150 pitch

LED Indicators

D2: When this green LED is lit, it indicates that power is applied to the +5V input.

D6 – D7: These two LEDs monitor the operation of the Ethernet communications circuitry.

Acc-2P Hardware Reference Summary

39

Image 45
Contents PMAC2A-PC/104 Delta Tau Data Systems, Inc. Technical Support Copyright InformationTable of Contents Software Setup Base Board Connector Pinouts PMAC2A PC104 Hardware Reference Manual Table of Contents Introduction Board ConfigurationAcc-1P Axis Expansion Piggyback Board Option 12 Analog-to-Digital ConvertersAcc-1P Option 1 I/O Ports Acc-1P Option 2 Analog-to-Digital ConvertersAcc-2P Option 1A USB Interface Acc-2P Communications BoardAcc-2P Option 1B Ethernet Interface Acc-2P Option 2 Dpram CircuitryPMAC2A PC104 Hardware Reference Manual Introduction Base Board Hardware Setup Clock Configuration JumpersBoard Reset Jumpers Configuration Jumpers CPU Jumper ConfigurationResistor Packs Configuration Communication JumpersDevice Resistor Pack Pack Size PMAC2A PC104 Hardware Reference Manual ACC-1P Hardware Setup Reserved Configuration JumpersE0 Reserved for future use Handwheel Encoder Termination Resistors ACC-2P Hardware Setup Jthw Connector DATx SELxJopt Connector E10 MOx MIx Lines Differential or Single-Ended Handwheel Encoder Selection Digital Power Supply Power SuppliesDAC Outputs Power Supply Machine ConnectionsMotor Signals Connections Overtravel Limits and Home SwitchesAmplifier Enable Signal AENAx/DIRn DAC Output SignalsPulse and Direction Stepper Drivers ExampleAcc-1P General-Purpose Digital Inputs and Outputs J7 Port Amplifier Fault Signal FaultAcc-2P General-Purpose Digital Inputs and Outputs Jopt Port Acc-1P Thumbwheel Multiplexer Port J2 PortAcc-2P Thumbwheel Multiplexer Port Jthw Port Acc-1P or Acc-2P Handwheel Port JHW / PD Port Optional Analog InputsCompare Equal Outputs Acc-2P USB Connector J1 Port Acc-2P Ethernet RJ45 Connector J10 PortSerial Port JRS232 Port PC DB-9Machine Connections Example Using Analog ±10V Amplifier PMAC2A PC104 Hardware Reference Manual PMAC2A PC104 Hardware Reference Manual Machine Connections Operational Frequency and Baud Rate Setup Software SetupCommunications Pmac I-VariablesFiltered DAC Outputs Configuration I54 Baud RateI54 Baud Rate for General-Purpose Digital Inputs and Outputs Using Flag I/O as General-Purpose I/OAcc-1P with Jumper E6 on Position Flag Type Channel NumberOpen PLC1 Clear Acc-2P with Jumper E5 in PositionAcc-1P with Jumper E6 in Position Thumbwheel Port Digital Inputs and OutputsAnalog Inputs Setup Baseboard Analog InputsAcc-1P Analog Inputs Base Board Hardware Reference Summary Board DimensionsFeature Feature LocationBoard Layout Connectors and Indicators Page ACC-1P Hardware Reference Summary TB1 JMACH1 J2 Thumbwheel Multiplexer Port Jthw Port J7 General-Purpose Digital Inputs and Outputs Jopt PortJ8 Handwheel / Pulse and Direction Port JHW / PD Port Page ACC-2P Hardware Reference Summary TB1 Jthw Jopt J1 USB Communications Port J8 Handwheel/Pulse and Direction Port JHW / PD PortJ10 Ethernet Communications Port Page E1 Servo and Phase Clock Direction Control E0 Forced Reset ControlE3 Normal/Re-Initializing Power-Up/Reset Base Board E-POINT Jumper DescriptionsE9 Servo Clock Lines Output Enable E8 Phase Clock Lines Output EnableE10 E12 Power-Up State Jumpers Description DefaultE14 Watchdog Disable Jumper E13 Power-Up/Reset Load SourceE16 ADC Inputs Enable E15A, B, C Flash Memory Bank SelectE18 E19 PC/104 Bus Address Point and Physical Location Description Default LayoutACC-1P E-POINT Jumper Descriptions E1 E2 Machine Output Supply Voltage ConfigureE0 Reserved for Future Use E3 E4 JHW, PD Function SelectE5 Servo Gate Address Select E6 I/O Gate Address SelectE7 Machine Input Source/Sink Control ACC-2P E-POINT Jumper Descriptions E1 USB/Ethernet Micro-Controller Firmware Reload EnableE5 I/O Gate Address Select E6 Communications Port SelectE7- E10 Ports Direction Control Point and Physical Location Description DefaultTB1 Jpwr Power Supply Base Board Connector PinoutsJ4 JRS232 Serial Port Connector Pin# Symbol Function DescriptionJ3 JMACH1 Machine Port Connector J3 JMACH1 50-Pin Header J4 JMACH2 Machine Port Baseboard Connector ACC-1P Connector Pinouts Pin# Symbol J2 Jthw Multiplexer Port ConnectorJ3 JMACH1 Machine Port Connector Pin Header J3 JMACH1 50-Pin-Header FLG78V Connector 34-Pin HeaderJ7 Jopto I/O Port Connector J8 JHW Handwheel Encoder Connector Page ACC-2P Connector Pinouts Pin # Symbol FunctionJ1 USB Universal Serial Bus Port Optional Pin Connector J7 Jopt I/O Port Connector Pin # Function J10 Ethernet Port Optional