Netopia R7200 manual Navigating through the console screens, Pc Ansi-Bbs

Page 46

6-4 User’s Reference Guide

Launch your terminal emulation software and conﬁgure the communications software for the values shown in the table below. These are the default communication parameters that the Netopia R7200 uses.

Parameter	Suggested Value

Terminal type	PC: ANSI-BBS
	Mac: ANSI, VT-100, or VT-200
Data bits	8
Parity	None
Stop bits	1
Speed	57600 bits per second
Flow Control	None

Note: The router ﬁrmware contains an autobaud detection feature. If you are at any screen on the serial console, you can change your baud rate and press Return (HyperTerminal for the PC requires a disconnect). The new baud rate is displayed at the bottom of the screen.

Navigating through the console screens

Use your keyboard to navigate the Netopia R7200’s conﬁguration screens, enter and edit information, and make choices. The following table lists the keys to use to navigate through the console screens.

To...	Use These Keys...

Move through selectable items in a screen or pop-up menu	Up, Down, Left, and Right Arrow

Set a change to a selected item or open a pop-up menu of	Return or Enter
options for a selected item like entering an upgrade key

Change a toggle value (Yes/No, On/Off)	Tab

Restore an entry or toggle value to its previous value	Esc

Move one item up	Up arrow or Control + K

Move one item down	Down arrow or Control + O

Display a dump of the device event log	Control + E

Display a dump of the WAN event log	Control + F

Refresh the screen	Control + L

Go to topmost selectable item	<

Go to bottom right selectable item	>

Image 46

Contents Netopia R7200 Sdsl Router Part Number Contents Part II Advanced Configuration Contents Aurp Snmp Xmodem Part III Appendixes User’s Reference Guide Part I Getting Started User’s Reference Guide Chapter Introduction Features and capabilitiesOverview How to use this guide Chapter Setting Up Internet Services Finding an Internet service providerPricing and support Setting up a Netopia R7200 account Obtaining an IP addressUnique requirements Endorsements Deciding on an ISP accountWith Network Address Translation Obtaining information from the ISPLocal LAN IP address information to obtain Without Network Address TranslationUser’s Reference Guide Chapter Making the Physical Connections Find a locationIdentify the connectors and attach the cables What you needNetopia R7200 Sdsl Router back panel ports Your router onNetopia R7200 Sdsl Router status lights Netopia R7200 LED front panelChapter Connecting to Your Local Area Network Readying computers on your local networkUser’s Reference Guide Connecting to an Ethernet network 10Base-T Adding an external modem Connecting to a LocalTalk network Chapter Setting up your Router with the SmartStart Wizard Before running SmartStart Setting up your Router with the SmartStart Wizard SmartStart Wizard conﬁguration screensAdvanced setup Easy optionAdvanced option Conﬁguration screen on Dynamic conﬁguration recommended Conﬁguration tabStatic conﬁguration optional Add. Repeat this process for the secondary DNS Conﬁguring TCP/IP on Macintosh computers TCP/IPTCP/IP or MacTCP Dynamic conﬁguration using MacIP optional Setting up your Router with the SmartStart Wizard User’s Reference Guide Chapter Console-Based Management Connecting through a Telnet session Connecting a console cable to your router Conﬁguring Telnet softwareNavigating through the console screens PC ANSI-BBSEasy Setup console screens Chapter Easy SetupAccessing the Easy Setup console screens See Appendix A, Troubleshooting, for more suggestions Quick Easy Setup connection path Sdsl Line Conﬁguration Main Menu appearsEasy Setup Proﬁle Previous Screen Next ScreenIP Easy Setup Easy Setup Security Conﬁguration Previous Screen To Main Menu Part II Advanced Configuration User’s Reference Guide Chapter WAN and System Configuration WAN conﬁgurationATM VPI ATM VCI Creating a new Connection Proﬁle IPX Profile Parameters Remote IPX Network Datalink PPP/MP Options Data Compression Default proﬁle Main Menu Default Proﬁle screen appears IP parameters default proﬁle screen IPX parameters default proﬁle screen System conﬁguration screensNavigating through the system conﬁguration screens System conﬁguration features IP address serving Network protocols setupFilter sets ﬁrewalls Date and timeConsole conﬁguration Security Upgrade feature setSnmp Simple Network Management Protocol LoggingInstalling the Syslog client User’s Reference Guide Chapter Line Backup Backup Conﬁguration screen appears Backup Conﬁguration screen AtdtIP Setup screen Using Scheduled Connections with Backup Connection ProﬁlesScheduled Connections screen appears Management/Statistics Force Recovery Event Logs QuickViewSnmp Support User’s Reference Guide Chapter IP Setup and Network Address Translation Network Address Translation featuresHOW NAT Works Using Network Address Translation Previous ScreenV2 multicast Numbered Associating port numbers with nodes Sdsl WAN1Advanced IP/IPX router conﬁguration options Data Link Options IP Setup and Network Address Translation Network Address Translation guidelines IP setup User’s Reference Guide Select Add Export. The Add Exported Service screen appears Select Service. a pop-up menu of services and ports appears IP subnets User’s Reference Guide Static routes Static Routes screen will appear Viewing static routesAdding a static route Modifying a static route Rules of static route installationDeleting a static route Main Menu System Configuration IP Address Serving 176.163.222.10 Dhcp NetBios Options Serve Bootp Clients IP Address Pools IP Setup and Network Address Translation Dhcp NetBIOS Options NetBios Type MacIP KIP forwarding setup You have ﬁnished your IP setup User’s Reference Guide IPX deﬁnitions Chapter IPX SetupIPX features Internetwork Packet Exchange IPXSocket Service Advertising Protocol SAPIPX address Routing Information Protocol RIPIPX setup screen NetBIOSIPX spooﬁng Default Gateway Address IPX routing tables User’s Reference Guide AppleTalk networks Chapter AppleTalk SetupAppleTalk protocol AT Routing Table MacIP Routers and seedingInstalling AppleTalk Upgrade Feature Set EtherTalk setup Conﬁguring AppleTalkLocalTalk setup Viewing Aurp partners Aurp setupAurp Free Trade Zone Adding an Aurp partner Modifying an Aurp partnerReceiving Aurp connections Deleting an Aurp partnerConﬁguring Aurp Options Aurp Options Tickle Interval Hhmmss User’s Reference Guide Chapter Monitoring Tools Quick View status overviewGeneral status Current status Status lightsStatistics & Logs General StatisticsPhysical Interface Event historiesNetwork Interface WAN Event History Routing tables Device Event HistoryIP routing table IPX Sap Bindery table IPX routing tableAppleTalk routing table Served IP Addresses IP Address Lease Management screen appears System Information SnmpSnmp Setup screen Community stringsSnmp traps Modifying IP trap receivers Setting the IP trap receiversViewing IP trap receivers Deleting IP trap receiversWeb-based management pages Event History pages WAN Event History Device Event History User’s Reference Guide Suggested security measures Chapter SecurityUser accounts Protecting the Security Options screen Protecting the conﬁguration screensDial-in console access About ﬁlters and ﬁlter sets Enable SmartStart/SmartView/Web serverTelnet access What’s a ﬁlter and what’s a ﬁlter set?How ﬁlter sets work Filter priorityHow individual ﬁlters work Parts of a ﬁlter ﬁltering rulePort numbers Port number comparisons Other ﬁlter attributesPutting the parts together UDPFiltering example #1 Filtering example #2Design guidelines Disadvantages of ﬁltersAn approach to using ﬁlters Working with IP ﬁlters and ﬁlter setsAdding a ﬁlter set Naming a new ﬁlter setInput and output ﬁlters-source and destination Adding ﬁlters to a ﬁlter setADD this Filter NOW Cancel Modifying ﬁlters Viewing ﬁlter setsViewing ﬁlters Deleting ﬁltersDeleting a ﬁlter set Modifying ﬁlter setsSample IP ﬁlter set TCP Icmp UDP Possible modiﬁcations User’s Reference Guide IPX ﬁlters Viewing and modifying packet ﬁlters IPX packet ﬁltersAdding a packet ﬁlter Viewing and modifying packet ﬁlter sets IPX packet ﬁlter setsDeleting a packet ﬁlter Adding a packet ﬁlter setNo Match Deleting a packet ﬁlter set IPX SAP ﬁltersViewing and modifying SAP ﬁlters Adding a SAP ﬁlter Deleting a SAP ﬁlterViewing and modifying SAP ﬁlter sets IPX SAP ﬁlter setsAdding a SAP ﬁlter set Deleting a SAP ﬁlter set Basic IP packet components Firewall tutorial General ﬁrewall termsBasic protocol types Example TCP/UDP Ports Firewall design rulesFirewall Logic Binary representation Logical and functionEstablished connections Implied rulesExample IP ﬁlter set screen Filter basics Example networkExample ﬁlters ExampleExample Example Chapter Utilities and Diagnostics Ping Receive return Ping packet Trace Route Stop PingTelnet client Factory defaults Disconnect Telnet console sessionTransferring conﬁguration and ﬁrmware ﬁles with Tftp Updating ﬁrmwareDownloading conﬁguration ﬁles Uploading conﬁguration ﬁles Transferring conﬁguration and ﬁrmware ﬁles with XmodemIdle Do you want to send a saved configuration to your Netopia? Restarting the system Part III Appendixes User’s Reference Guide Appendix a Troubleshooting Conﬁguration problemsConsole connection problems Network problemsHow to reset the router to factory defaults Power outagesBefore contacting Netopia How to reach usTechnical support Environment proﬁleOnline product information FAX-BackUser’s Reference Guide Appendix B Understanding IP Addressing What is IP?About IP addressing Subnets and subnet masks Example Using subnets on a Class C IP internet Subnet masksNetwork conﬁguration ISP NetworkDistributing IP addresses Example Working with a Class C subnetBackground Technical note on subnet masking Conﬁguration Netopia R7200 Dhcp server characteristicsDhcp address serving MacIP serving Using address servingManually distributing IP addresses Serve dynamic WAN clientsTips and rules for distributing IP addresses Understanding IP Addressing B-9Dhcp example Nested IP subnets Internet0.0 C.1 WAN 3719 Broadcasts Packet header typesUser’s Reference Guide Network conﬁguration Appendix C Understanding Netopia NAT BehaviorBackground User’s Reference Guide Understanding Netopia NAT Behavior C-3 Netopia Router WWW Server ISP Router LAN Exported services Understanding Netopia NAT Behavior C-5Important notes Understanding Netopia NAT Behavior C-7 Summary Appendix D Binary Conversion Table Decimal Binary Appendix E Further Reading User’s Reference Guide Further Reading E-3 User’s Reference Guide Appendix F Technical Specifications and Safety Information Pinouts for Auxiliary port modem cableDescription Power requirementsEnvironment Software and protocols North America Agency approvalsRegulatory notices InternationalImportant safety instructions Declaration for Canadian usersTelecommunication installation cautions BatteryAppendix G About Sdsl User’s Reference Guide Glossary User’s Reference Guide Glossary User’s Reference Guide Remapping See network number remapping User’s Reference Guide Glossary User’s Reference Guide Index NumericsIndex-2 Index-3 Index-4 Index-5 Index-6 Limited Warranty and Limitation of Remedies User’s Reference Guide