MicroBoards Technology II manual Copy CD-to-CD? OrCopy & Compare?, Yes Quantity?

Page 24

Orbit II Disc-to-Disc Copier Reference Manual – Revision I

Verify the distribution disc was copied properly:

Take the distribution disc copy from the Accept Basket and place it in the Input Hopper.

Press the No key at the prompts.

Copy CD-to-CD?

and

orCopy & Compare?

Press the

 

 

 

key at the

 

Compare CD?

prompt.

 

Yes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quantity? 00

 

 

 

 

 

 

 

 

 

When the

 

 

 

 

 

prompt appears, press

 

Yes

to accept the “10s”

 

 

 

 

 

 

 

 

digit setting

 

 

will move to the “1s” digit.

 

 

the

No

key once

 

of “0”.

The underline cursor

 

Press

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to set the “1s” digit to “1”. Press

Yes

to accept the “1s” digit setting of “1”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When the CD Reader tray opens, place the Orbit II distribution disc in the CD Reader tray and press Yes .

Orbit II will compare the master distribution disc to the copy, and place the copy in the Accept Basket if it passes the content verification test.

You can use this same test sequence to troubleshoot problems with your Orbit II System prior to calling for technical assistance. If you are trying to isolate media quality problems, substitute reference media for discs that have a high reject rate. If you suspect problems with a particular master, substitute a reference master. (You can use your distribution disc as a reference master.) If the term “reference media” or “reference master” is new to you, refer to Sections 3 & 4 of this manual.

When your Orbit II System passes the disc handling, writer, and reader tests it is ready for use. Proceed to Section 6 Basic Orbit II Operation.

If your Orbit II System does not pass the disc handling, writer, or reader test contact your Microboards Technology Technical Support for assistance.

24

Image 24
Contents Orbit II Stand Alone CD Disc-to-Disc Office Copier Table of Contents Introduction Setting Up your CD-R Copying Area CD-R & CD-RW Media Recommendations CD-R Media Recommendations CD, CD-R, and CD-RW Master Considerations Orbit II Disc-to-Disc Copier Reference Manual Revision Installation & Setup Unpacking the Orbit II and verifying shipment contentsInspecting the shipment for Damage Installing the Orbit Installing the Orbit II Installing the Orbit II Initial Orbit II Copying System Checks Navigating the Orbit II Menu TreeKey #1 the Yes key Key #2 the No keyCopy CD+G Karaoke discs Burn CD? Must be set to YES toNavigating the Orbit II Menu Tree Burn CD? Must be set to YES to run Copy and CompareAsk Quantity? to Loading & Unloading CD-Rs Loading CD-RsFirst 5 or 6 CD-Rs Loading Masters Yes At a Or a Copy CD-to-CD? Copy & Compare? Compare CD?Unloading Accepted CD-Rs Unloading Masters CD-R Handling Tests Quantity?Copy CD-to-CD? Copy & Compare? Compare CD? Writer and Reader Test Turn Burn CD? onCopympare& CD? Copy CD-to-CD? OrCopy & Compare? Yes Quantity?Basic Orbit II Operations Copy CD-to-CD?Copy and Compare? Copy CD-to-CD? Copy & Compare?Compare CD? Copy CD+GAdvanced Orbit II Operation Special NotesMaintenance Routine Maintenance Troubleshooting Prior to Calling for Assistance References Warranty Technical Support Telephone #Regulatory Agency Approvals Specifications Environment VibrationShock AltitudeCopy CD+G Karaoke discs Attachment B Orbit II Functional Schematic DC PowerAC Power Attachment C Orbit II Error Messages Attachment D What is BurnProof? Orbit II Disc-to-Disc Copier Reference Manual Revision