NorthStar Navigation 8000I Measure range and bearing, Find range and bearing with the cursor

Page 139

24 Measure range and bearing

This section explains how to:

•find the range and bearing

•show and hide a VRM/EBL

•find the range and bearing with fixed VRM/EBL

•find the range and bearing with floating VRM/EBL

•set the EBL reference bearing

24.1Find range and bearing with the cursor

You can use the cursor to quickly find the precise range and bearing of a target from your vessel.

You can also use one, or both, of the VRM/EBL (Variable Range Markers/Electronic Bearing Lines), see "Find range and bearing with fixed VRM/EBL".

To find the range and bearing of a target with the cursor:

1.Select the target on your Radar screen.

2.The range and bearing is shown in the status bar at the top of the Radar screen, next to the cursor readout. Select the cursor readout to show the Lat/Long position (if GPS data is available).

3.When you are finished, select Return.

NOTE: If there's no heading data available from a heading sensor, the bearing readouts are relative to your vessel's head.

24.2Show/hide a VRM/EBL

You can show or hide one, or both, of the VRM/EBL (Variable Range

Markers/Electronic Bearing Lines) on your Radar screen.

Off is the default and hides the VRM/EBL.

To show or hide VRM/EBL data:

1.Display the Radar screen and control panel. If you can't see the

Range and Bearing button, select Return.

2.Select Range and Bearing.

3.Select VRM/EBL 1 to show the control panel for VRM1 and EBL1. If Show VRM/EBL 1 is toggled Off, select it to toggle it On. The Radar screen shows:

ƒVRM 1. A thin, circular, dotted line centered around your vessel. The radius is set at the most recent position.

ƒEBL 1. A thin dotted line extending from your vessel to the edge of your Radar screen. The bearing is relative to your vessel. The default angle is 045° Relative.

Northstar 8000i Operation Manual

139

Page 138 Page 140
Image 139
Page 138 Page 140
Contents Northstar Important Safety Information Important Safety and Warning InformationPage Minimum safe Vertical beam Distance Watts per m² Scanner Disclaimer WarrantyContents Chart Set up the chart library Use the chart views 3D Steer Sounder 101 Radar 123 Measure range and bearing 139 Entertainment 162 Video jukebox options 179 Glossary Networking Welcome to the NorthstarConventions How to use this manualTurn on Introduction to the NorthstarTurn off To turn off the 8000i using a 12 Display ProcessorKeys on the 15 inch Monitor Menu Control Keys on the remote keypadKeys on the 12 inch Display Processor To select an item with the touch screen How to select an itemButtons Single pane optionsWhat are pages? What is the active pane?Cycle through the panes on a Expand a small paneEdit a Select aSounder, Cruising, and Fishing Adjust the brightness on the 15 inch Monitor Set up the Northstar 8000i basicsAdjust the brightness on a 12 inch Display Processor Turn the keypad beeps on or off Adjust the volumeTurn the keypad backlight on or off Show/hide the top control bar Select a paletteShow/hide the control panel Show/hide the instruments barSelect the time format When you are finished, select InstallationSelect your time zone Select the large scale distance units Select the temperature unitsSelect the small scale distance units Select the depth units Select the volume units for liquidsSelect the speed units Select the pressure units When you are finished, select Vessel StatisticsSpecify your vessel statistics Chart Select + Chart Select C-Map Chart Manager Set up the chart libraryDisplay the C-MAP MAX Pro Chart Manager screen What does the C-MAP PRO Chart Manager screen show?Chart Manager icons Chart Manager control panelCollection is installed on Different ways to choose a chart collection Information on C-Map chart licenses and subscriptionsPurchase or rent? Page Purchase a chart license over the phone Purchase a chart license over the internetPurchase a chart license through a dealer Install the chart data Load the chart licensesSelect + Chart, then C-Map Chart Manager Touch Install Selected Touch Install All in Control PanelUpdate charts over the internet Uninstall chart collections Update the database by DVDEnter C-Map MAX Pro Chart Manager Page Display the chart screen Chart screen basicsTo display the chart screen You can either What does the chart screen show? GoTo or show a Lat/Long coordinate Display your current position in real timeDisplay your current position data Instant GoToPan the chart Zoom in or out on a chart screenZoom in or out on part of a chart screen What is the chart orientation? Change the chart viewThere are three choices of chart orientation What is the vessel offset mode? Change the chart orientationSelect the level of chart detail Select the vessel offset modeShow details about an object on the chart Show range and bearing between two points Show range and bearing from your vesselDistance button, select Return Select Distance and a new control panel appears Show/hide the course predictor line Customize the chart screenWhat is the course predictor line? Show Predictor button, select SettingsSettings button, select Return Select Settings Keep your vessel in view on the chart screenSelect the vessel symbol What is the chart guard zone?Turn the chart guard zone on or off Set up the chart guard zoneSet the deep water contour Select the default icon for a waypointSelect the default icon for an event mark Guard Zone button, select SettingsChart Presentation button, select Settings Show/hide the chart boundariesShow/hide your current track Show/hide shade safe depths Select Chart Presentation, then select More Chart SettingsShow/hide the Lat/Long grid overlay Show/hide tidal flow and currents Select Chart OverlaysWhat are light sectors? Show/hide the light sectorsDefault settings for the chart views Use the chart viewsFive chart views have the following default settings Page Overlay the radar Use the chart overlaysTransmit Select Chart Overlays, then select Radar Settings Adjust the settings for the radarChange the radar mode Adjust the radar opacityOverlay the ports and marinas Overlay satellite or aerial photosOverlay roads, terrain, SAR and/or Gmdss areas Select Chart Overlays, then More Overlays Create a waypoint Use waypointsCreate an event mark Hide a waypoint Select and show a waypoint on the chartDelete a waypoint Stop navigating to a waypoint Navigate to a waypoint10.8 Set/remove the warning zone for a waypoint Display the waypoint details Find a waypointSelect the waypoint, then select Waypoint Details Display the waypoints library Change the waypoint detailsDelete a waypoint from the Waypoints Library Copy an existing route Use routes and waypointsCreate a new route ƒ Off, a new waypoint is located exactly where you chooseMove a waypoint in a route When you are finished, select FinishAdd a new waypoint into a route Add a waypoint to the start or end of the route Remove a waypoint from a route using the Chart screen Remove a waypoint from a route using the Routes LibraryReturn Change the order of the waypoints in a routeAdd an existing waypoint to a route ƒ select Edit Route then select Remove WaypointSelect and follow a route from the Routes Library Display the Routes LibrarySelect and follow a route with GoTo Select the route that you want to follow, then select OK Follow a routeNavigate to the previous or next waypoint Stop following a routeDelete a route Hide an inactive routeReverse your route Select GoTo then select Reset XTE Reset the XTE on an active route or waypointDisplay and/or change the route details Show the route length and estimated travel time Set up routes to be shown or hiddenPage Select the bearing mode Set up navigationSet the manual variation Select the variation sourceSelect the position data format Set the look ahead distance to update chartSet the center circle to update chart Set the waypoint arrival distance Set the angle delay to update the chartSelect whether to continue navigating at the route end Display the 3D Chart screen Introduction to 3D ChartReposition the 3D Chart screen to show your vessel Rotate the view of the 3D Chart manually Pan the 3D Chart to show new areasChange the azimuth setting on 3D Chart Change the elevation manually Change the camera angle for 3D ChartEnhance the vertical scale Change the vessel modeShow/hide the bathymetric data Synchronize 3D Chart and the chart screen Overlay satellite or aerial photos on 3D ChartPage What does 3D Steer show? When to reset the XTE14 3D Steer Display the 3D Steer screen100 Use the sounder SounderHow the sounder works What does the sounder screen show? Display the sounder screenChange the scroll speed What does the sounder status bar show?Depth at the current cursor position Change the palette Palette button, select SettingsShow/hide the depth value Move the depth line Change the sounder operating modeAuto Mode button, select Return Show/hide the depth lineWhen to use 50 kHz, 200 kHz, or mixed frequency Select a split 50/200 kHz screen Select 50 kHz, 200 kHz or mixed frequency screenFrequency button, select Return Select a split zoom screen What is zoom range and zoom range shift?Change the zoom range shift Change the ratio of a split screen Select a split bottom lock screenWhat is the A-Scope? Change the ratio of the A-Scope Show/hide the A-ScopeProblems with fish arches? How to interpret the sounder screensWhat are fish arches? How the water depth and scroll speed affect the history How to recognize different types of fishHow to recognize and avoid shadows How to recognize the type of bottomFactors that affect the echo strength Gain and Filters button, select Return What is gain?Change the gain setting Change the sounder range and gainChange the gain threshold What is the gain threshold?Turn the auto range on or off What is auto range and range shift?Auto Range can be set On or Off Change the range Change the range shiftRange, Zoom and Split button, select Return Change the transducer depth Set up the sounderChange the water temperature averaging time Change the water temperature offsetChange the sounders speed offset Change the zoom range Change the sounders speed filterReturn Select Range, Zoom, and Split 122 How the radar works RadarWhat are the radar modes? 124 Display the radar screen Use the radarStart the radar transmitting What does the radar screen show? Stop the radar transmittingWhat does the radar status bar show? What is the radar orientation?Orientation button, select Return Change the radar orientationChange the radar range offset Customize the position of the PPI centerSet the PPI position to Look Ahead or Center Select True or Relative Motion modeOrientation button, select Return Select Orientation Reset the TM position Adjust Radar button, select Return Select Adjust Radar Change the radar gain modeOptimize the quality of the radar display What is sea clutter? Change the radar gain settingChange the sea clutter mode What is rain clutter? Change the sea clutter settingReduce interference from other radars Change the rain settingPresentation button, select Return Select Presentation 135 Customize the radar screen Show/hide the North indicatorChange the radar palette Show/hide the range rings Show/hide the heading markerShow/hide the active waypoint on radar Show/hide waypoint or route details on radar Show/hide the active route on radarFind range and bearing with the cursor Measure range and bearingShow/hide a VRM/EBL Find range and bearing with fixed VRM/EBL Find range and bearing with floating VRM/EBL Set the EBL reference bearing Make small targets more easy to see Target presentationTurn off or customize target trails Remove target trails from the radar Guard Zones button, select Return Select Guard Zones What is a radar guard zone?Use the radar guard zones Turn a radar guard zone on or offCustomize a radar guard zone Set the sensitivity of the radar guard zone alarmGuard Zones button, select Return 147 Change the radar antenna height Set up the radarChange the radar startup mode When you are finished, select RadarChange the radar bearing alignment Change the range of the radar150 Rename an instrument panel Choose how to view the instrumentsInstruments Select an instrument panelSelect Panel button, select Return Select the color scheme for an instrument panelChange the layout of the instrument panel Resize an instrumentAdd an instrument Delete an instrument panel When you are finished, select Save ChangesCreate an instrument panel Delete an instrumentSelect Config, then select Panel Config Which alarms can be changed? AlarmsView the current settings for an alarm Change the upper or lower trigger settings for an alarm Turn an alarm On/OffSet the alarm audio Set the delay for an alarm View the alarm log Trigger an alarm in case of a loss of input dataAcknowledge All Acknowledge one or more alarmsSet an anchor alarm Reset an alarmEntertainment Show multiple entertainment panes Turn the volume up or downWhat file formats are supported? Copy media files to a portable drive Manage your media files with a portable driveCopy media files from a portable drive Delete media files from a portable drive Play media files from a portable driveFiles must be in WMA, MP3, MPEG, WMV or AVI format 167 Entertainment Delete an item from the music libraryDelete a video from the video library Select and play music from the jukebox Use the music jukeboxRepeat the whole album or playlist in the jukebox Pause playing music from the jukeboxPlay the previous or next track in the music jukebox To create a new playlist Change an albums cover artCreate and name a new playlist To change an albums cover artSelect Create/Edit Playlist, then choose Select Playlist Change a playlistPlay tracks randomly in the album or playlist Delete a playlistView the music details Edit an item in the music libraryQueue more music Select and play a playlistSelect a particular track on a music CD 35 CD/DVD optionsPlay a music CD Set random play On/Off on a music CDResume playing a music CD Set repeat play On/Off on a music CDPlay the previous or next track on a music CD Pause playing a music CDStop and eject a music CD Select and play a video Video jukebox optionsYou can use the video jukebox options to Fast forward a video Play a video in full screen modePause or resume playing a video Stop or restart a videoTo play a different video Rewind a videoSet repeat play On/Off for a video Play a different videoShow the DVD menu Play a DVD in full screen modeDVD options Play a DVDFast forward a DVD Play or resume playing a DVDStop or restart a DVD Play the previous or next scene on a DVDStop and eject a DVD Rewind a DVDTo rewind a DVD Manage your Media Libraries Change the automatic ejection setting for music CDsSet the volume levels for the entertainment applications When you are finished, select EntertainmentSet the location of the media library Select the audio source for Video Aux Video AuxWhat video formats are supported? Select and play the Video Aux In sourcePlay Video Aux In in full screen mode Add the camera to the network View the camera in full screen modeCamera What types of camera are supported?Maintain the Northstar How to clean the touch screenHow to clean a display unit Restore settings and informationSelect Calibrate next to Calibrate Touch Screen Technical support, service and repairsFind the software version number Upgrading the 8000i systemThere two types of upgrade for a 8000i processor Sounder Bottom is not displayed TroubleshootingTouch screen is inaccurate Camera screen goes blank or camera isnt availableRadar shows different patterns on each sweep Radar overlay doesnt appear on the chart screenRadar shows random signals in center Radar shows random or grouped dotsRadar shows false echoes and/or background noise Charts wont display42.14 3D Chart wont display photo overlays 42.15 3D Chart photo overlays switch offSelect Routes Tracks and Waypoints Restore routes, tracks, and waypointsRestore global settings Select Restore Global SettingsSee Networking the 8000i for more information Restore local settingsSelect Restore Local Settings Gray screen with message Master name unavailableGlossary Representation of a fish on the screen as a raw echo return Final waypoint in a routeType of fuel. See also gasoline and petrol An advanced home theatre soundWay of grouping music by style, e.g. Rock, Classical Method of displaying information without using colourUnit of volume equal to 1.20094 US gallons Type of fuelList of options displayed on screen Unit of volumeDisable the audio output Camera attached to the mastPlay the selected track or tracks Chart is displayed with North at the top of the screenAdvance to the next track of the CD or DVD Waypoint that you are steering towardsSet of software instructions for a computer Power output of the sonar transmissionRange and bearing between two points selected on the chart See Range ChartingAn area that cannot be reached by the sonar pulse Setting to display the track of the boat over the chartList of stored routes Speed at which the display moves across the screenList of stored waypoints in the database Sudden change of temperature over a short vertical distanceUnit of volume equal to 0.833 Imperial gallons List of tracks recorded and stored on the databasePortion of the display screen that shows the zoomed area Area of the display that is enlargedIndex 124 168 206 208 209 147 56, 71 211 212 Man Overboard Page United States Europe Northstar
Related manuals
Manual 45 pages 16.7 Kb

8000I specifications

The NorthStar Navigation 8000i is a sophisticated marine navigation solution designed to enhance the safety and efficiency of marine operations. Utilizing the latest technology and innovative features, the 8000i provides users with a comprehensive navigation tool that is both user-friendly and highly reliable.

At the heart of the NorthStar 8000i is its advanced GPS integration, which delivers precise positioning and navigation capabilities. The system supports multiple satellite systems, allowing for exceptional accuracy and reliability in determining a vessel's location, even in challenging conditions. The 8000i uses Differential GPS (DGPS) to further improve positional precision, making it suitable for commercial vessels and recreational boaters alike.

One of the standout features of the NorthStar 8000i is its large, high-resolution color display, which presents information in a clear and accessible manner. The screen offers customizable layouts, allowing users to prioritize the data they find most critical. The interface is designed with simplicity in mind, enabling users to access navigation tools, charts, and other features quickly and easily.

The NorthStar 8000i is equipped with advanced cartography options, including support for a variety of chart formats. Users can choose between vector and raster charts, ensuring that they can find the best option for their specific needs. The system also supports both local and regional data, providing an extensive coverage area for vessels operating in different waters.

In terms of connectivity, the 8000i features integrated networking capabilities, allowing it to interface seamlessly with other marine electronics such as radar systems, autopilots, and AIS transceivers. This interoperability enhances situational awareness and provides a comprehensive picture of the marine environment around the vessel.

The rugged design of the NorthStar 8000i ensures that it can withstand the challenging conditions often encountered at sea. Built to be weatherproof and durable, this navigation system is ready for any marine adventure.

To summarize, the NorthStar Navigation 8000i combines cutting-edge GPS technology with user-friendly designs and exceptional features, making it a top choice for navigators seeking reliable marine navigation solutions. With its accuracy, customizable interfaces, and robust construction, the 8000i is engineered to meet the diverse needs of modern sailors, whether for leisure or professional undertakings.
Top Page Image Contents