4 Press ENTER.
Audyssey 2EQ® Room Correction and Speaker Setup starts.
Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey 2EQ Room Correction and Speaker Setup, unless you want to cancel the setup.
If you select “Audyssey Quick Start”, you will go to step 7.
5 Place the setup microphone at the next position, and then press ENTER.
Audyssey 2EQ performs more measurements. This takes a few minutes.
6 When prompted, place the setup microphone at the next position, and repeat step 5.
7 Use q/wto select an option, and then press
ENTER.
2EQ: Auto Setup |
| Audyssey |
<- Review Speaker Configuration | ||
Subwoofer | : | Yes |
Front | : | Small |
Center | : | Small |
Surround | : | Small |
Surr Back | : | Small |
Surr Back Ch | : | 2ch |
Crossover | : | 100Hz |
Save
Cancel
The options are:
`Save:
Save the calculated settings and exit Audyssey 2EQ Room Correction and Speaker Setup.
`Cancel:
Cancel Audyssey 2EQ Room Correction and Speaker Setup.
Note
•You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using e/r.
8 Use q/wto select a target, and use e/rto change the setting.
After the results of Audyssey 2EQ have been saved, the menu will display the “Audyssey” (➔ page 44), “Dynamic EQ” (➔ page 44), “Dynamic Volume” (➔ page 45) settings.
Note
•When “Audyssey Quick Start” has been used for measurement, “Audyssey” cannot be selected.
•These settings are applied to all input selectors.
9 Press ENTER.
10 Disconnect the speaker setup microphone.
Note
•You can cancel Audyssey 2EQ Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.
•Do not connect or disconnect any speakers during Audyssey 2EQ Room Correction and Speaker Setup.
•If the AV receiver is muted, it will be unmuted automatically when Audyssey 2EQ Room Correction and Speaker Setup starts.
•Changes to the room after Audyssey 2EQ Room Correction and Speaker Setup require you run Audyssey 2EQ Room Correction and Speaker Setup again, as room EQ characteristics may have changed.
Error Messages
While Audyssey 2EQ® Room Correction and Speaker Setup is in progress, one of the error messages below may appear.
2EQ: Auto Setup | Audyssey |
Ambient noise is too high. 
Error message
Retry
Cancel
The options are:
`Retry:
Try again.
`Cancel:
Cancel Audyssey 2EQ Room Correction and
Speaker Setup.
• Ambient noise is too high.
The background noise is too loud. Remove the source of the noise and try again.
• Speaker matching error!
The number of speakers detected was different from that of the first measurement. Check the speaker connection.
• Writing Error!
This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact your Onkyo dealer.
• Speaker Detect Error
This message appears if a speaker is not detected. “No” means that no speaker was detected.
Tip
•See “Speaker Configuration” for appropriate settings (➔ page 12).
Changing the Speaker Setup Manually
You can manually make changes to the settings found during Audyssey 2EQ Room Correction and Speaker Setup.
See also:
•“Sp Config (Speaker Configuration)” (➔ page 41)
•“Sp Distance (Speaker Distance)” (➔ page 42)
•“Level Cal (Level Calibration)” (➔ page 42)
En
29
