Texas Memory Systems RamSan-300/320 manual Dhcp

Page 30

•Enables you to set a static IP address for the RamSan.

•Sets the IP configuration to

DHCP

•Disables Ethernet

•Returns to the Main Menu without making any changes

Static

DHCP

None

No change

Talk to your network administrator for the proper IP assignment type. The default factory setting is DHCP. Use the “Select” button to select the desired method of IP assignment. If you did not choose “Static IP” you are asked to confirm the selection with the “↓” button.

To configure the RamSan with a static IP, the system requires the IP address, subnet mask, and a possibly a gateway address.

After you have chosen

“Static IP,” “Ethernet IP” replaces the top line of the display, and the display prompts you to enter an IP. Use the “↑” or “↓” buttons to cycle through the numbers “0” through “9”. To select the value, use the “Select” button. Then, the input prompt moves to the next character position. To back up a space, press the “↑” and “↓” button simultaneously. Repeat this procedure until you have entered the 4-byte address. Press the “Menu” button at any time to cancel the Static IP assignment.

Ethernet IP

_

RamSan-300/320 User’s Manual

- 26 -

Image 30

Contents RamSan-300/320 User’s Manual RamSan-300/320 User’s Manual Table of Contents Batteries Fans Document Overview Safety PrecautionsPreface ConventionsRevision History Following table describes revisions to this documentIntroduction OverviewPower System ComponentsNon-Volatility Configurable Backup Active BackupTM mode optionalPerformance Electro-Static Discharge Warning InstallationBattery Warning System InspectionRamSan-320 Rack Mounting Connecting the Fibre Channel PortsConnecting the Power Supplies FC 4 FCPower AC Voltage Power switchAC Voltage indicator light Turning on the SystemSystem Initialization System is now ready for normal operation Management Tool Overview Front Panel DisplayConnecting using a terminal program Text Management InterfaceFront Panel menu system layout Connecting using Telnet General interface layout and instructionsText Management Interface Sub-Menu Web Management Interface Scrolling Sub-MenusWeb Management Interface Security Administration FunctionsSet password Logging into the systemVia Web Interface Click on the Management Control Processor graphicEnable/disable Telnet Via Text ManagementEnable/Disable Telnet Via Web ManagementFrom the Telnet Main Menu, select Management setup Telnet SetupEnable/disable Web Interface Enable/disable SnmpConfiguring Ethernet settings Configuring Ethernet settings via Front PanelDhcp Subnet Mask Configuring Ethernet settings via Text Management Interface Select IP assignment modeVia Front Panel Display Power Down SettingsManual shutdown Select Select hostnameFrom the Telnet Main Menu, select Power down system Automatic shutdownViewing system health and status Restore/Synchronize ProgressMonitoring Functions Front panel monitoringError StatusActive Monitor Mode Fibre Channel PerformanceLED Performance Monitoring LED DisplayIdentifying a RamSan Identify Device buttonViewing system uptime System Uptime StatusFrom the Telnet Main Menu, select Health and Status Health and StatusViewing system health Disk Status via Web interfaceBatteries Not displayed for the RamSan-300 Management Control Processor Power supplies Fans Good Viewing detailed fibre channel controller status 10 Fibre Channel Controller Status via Web InterfaceVia Text Management Statistics Viewing IO/second summary Via Web Interface13 IO/sec Summary Viewing bandwidth summary 14 Bandwidth Performance Graph via Web Interface15 Bandwidth Performance via Text Management Interface Viewing the system event and support logs LogsViewing controller details Click the Management Control Processor graphicClearing logged ECC errors Clearing the system event logFibre Channel LUN ConfigurationGigabytes System Memory ControllerExample LUN configuration Reconfigured LUN MappingAdding LUNs Via Web InterfaceSelect Change number of LUNs to add From the Telnet Main Menu, select LUN Setup Select Add LUNsVia Text Management Select Change size of LUNs to addViewing LUN status / LUN map Via the Web InterfaceTo view the LUNs for the entire system Viewing LUNs Assigned to FC ports via Web Interface Linking LUNs to/from Fibre Channel Controllers LUN Map ScreenSelect Exit to the LUN configuration menu Via Text Management Linking Fibre Channel ControllersUnlinking Fibre Channel ports from LUN Select Unlink LUNs from selected controllerChanging LUN numbers Select Assign different LUN # to this LUNResizing LUNs Select Resize LUNManaging access lists Viewing Current Access ListsSelect Print detailed WWN mask list for LUN Adding Access Lists Deleting Access ListsSelect Delete WWN mask from LUN Setting Scsi device identifiers Select Set Scsi device identifierDeleting LUNs 14 Deleting LUNs via Web InterfaceSetting backup mode 15 Deleting LUNsSelect Set backup mode for this LUN Volatile mode optional Fibre Channel Controller Configuration Changing Fibre Channel topology and link speedSelect Change topology Select Change link speedSelect Save changes and exit Auto-Detect Error Configuring high availability From the Telnet Main Menu, select Controller setupPrimary Active Primary Active, Secondary is Secondary Passive, Primary isPrimary Passive, Secondary is Secondary Active, Primary is System Maintenance Hot Swapping Power SuppliesHot Swapping Disk Drives Batteries FansSystem Event Log TroubleshootingStill Having Problems… Support LogOperating Environment SpecificationsPhysical Characteristics Non-operating EnvironmentAppendix a RamSan-3xx Series Replacement Parts Figure A-1 MCP-65 Management Control ProcessorFigure B-3 Power Supply Module Figure A-6 120 Gigabyte Replacement Hard Drive Appendix B FCC/Safety Notices Telephone and Software Support Field ServiceReturn to Factory Repairs/ReturnsSilver Warranty Advanced Parts Replacement Gold Warranty On-site Repair Business HoursPlatinum Warranty On-site Repair 24/7 Outside of Warranty