Uniden BC796D APC0 25 manual Problem Suggestion

Page 65

Problem

 

Suggestion

 

 

 

APCO P25 CARD

1.

Check to see if the P-25 Card is properly installed.

NOT INSTALLED

 

 

appear when the scanner

 

 

is turned ON.

 

 

 

 

 

Neither APCO P25

1.

Check to see if the P-25 Card Mode is 1:ENABLE or

CARD INSTALLED

 

2:DISABLE in the Menu mode.

9600 SYSTEM nor

 

 

APCO P25 CARD

 

 

NOT INSTALLED

 

 

appear when the scanner

 

 

is turned ON.

 

 

 

 

 

Scratchy or robotic sound

1.

Move to a location where the signal strength is strong.

is heard during

2.

Modulation accuracy of transmissions sent can be low.

communications.

 

 

 

 

 

Digital communication is

1.

Verify the accuracy of the frequencies of the P-25 system you

not heard.

 

are trying to monitor.

 

2.

You might be in a dead-spot for the P-25 system you are trying

 

 

to monitor. Check other locations in the area.

 

 

 

DATA sound is heard at

1.

APCO project 25 systems can send data before voice

the beginning of digital

 

communication.

communications.

2.

Data sound can be heard when signal strength is weak.

 

 

 

Robotic sound is heard.

1.

Check to see if the ENC message appears on the display.

 

 

The scanner doesn’t monitor encrypted voice communications.

 

 

 

When CARD ERROR

1.

Re-install the P-25 Card.

appears every 10 seconds

 

 

while you are using P-25

 

 

Card.

 

 

If you still cannot get satisfactory results while using your scanner or if you want additional information, please call or write the Uniden Parts and Service Division. The address and phone number is listed in the warranty at the end of this manual. If you would like immediate assistance, please call Customer Service at (800)297-1023.

If you have internet access, you can visit scanner.uniden.com for additional information.

59

Image 65
Contents Page Page Contents Programming Trunked Systems General Use Location Cleaning Repairs Birdies Page FCC Wants You To Know Scanning Legally Introduction Page Using this Manual Conventional Scanning Understanding ScanningSimplex Operation Repeater OperationMotorola Trunking Trunked ScanningEdacs Trunking LTR Trunking Understanding Banks and ChannelsGetting More Information BC796D Front and Rear ViewIcon Description Display IconsIncluded With Your Scanner Connecting an Antenna Setting Up Your ScannerMounting an Antenna Optional AntennaMounting the Scanner in Your Vehicle Typical Mounting MethodsApplying Power for Vehicle Installation Applying Power Using Standard AC Power Desktop InstallationConnecting an External Speaker Connecting an EarphoneConnecting the Tape Recorder Connecting the Clone CableListening Safely RememberTurning On the Scanner Setting the SquelchBasic Operation Manually Selecting a Channel Using the MenuScanning Programmed Channels Locking/Unlocking BanksRestoring All Locked Out Channels Locking/Unlocking ChannelsPriority Scanning Priority Plus ScanningControlling How Much Information Appears Dimmer Light SettingTurning the Key Beep On/Off Locking the Enter keyDisabling the APCO25 Card Setting Squelch ModeMuting All Audio Trunk Scanning OptionsMonitoring Talkgroup ID’s Scanning Only Stored Talkgroups ID ScanSelecting Talkgroup Lists to Scan Holding on a Single TalkgroupEdacs Patch Tracking Edacs BlockoutUnlocking All Talkgroups Setting Data Skip Setting Chain SearchSearching Holding on an Active FrequencyAutomatically Storing Frequencies Storing Found FrequenciesSetting Delay for All Search Ranges Setting Subaudible Tones for SearchingSearching for Subaudible Tones Attenuating All Search RangesSearching for Trunk Systems Setting a Search RangePage Service Search Skip Service SearchSearching for a Weather Broadcast Using Weather Search and Weather Alert SameUsing Weather Alert Same Testing the Weather Alert Assigning Bank Names Bank ConfigurationProgramming Bank Information Deleting Frequencies from Channels General ProgrammingTransferring Channel Information Entering Alpha InformationPage Select a Channel to Program Programming Conventional ChannelsEnter the Frequency Assigning a Text TagSetting the Subaudible Tone Option Setting the DelayChanging the Frequency Step Setting Beep AlertSetting the Attenuator Setting Priority Channels Setting the Modulation ModeProgramming Trunked Systems Turning I-Call On and Off for ID Search Setting Trunking DelayUsing I-Call Motorola and Edacs only Multi-Track Setting Priority Talkgroups Motorola and Edacs onlyTurning I-Call On for ID Scan Multi-Track Operational DetailsPage Programming Type 2/Digital 800 and 900 MHz Systems Using Control Channel ProgrammingProgramming Motorola Systems Programming Type2/Digital VHF and UHF Systems Programming Type I and IIi Hybrid Systems Toggling End Code Detect Toggling the Status BitProgramming Edacs Channels Setting Edacs Emergency AlertProgramming Edacs Systems Setting Edacs Decimal Mode Programming Apco 25 Systems Setting Apco 25 Sound QualityProgramming LTR Systems Storing Found Talkgroups Programming TalkgroupsStoring Known Talkgroups Seeing Talkgroup Activity Deleting Stored Talkgroup ID’sAdding a Text Tag to an ID List Cloning Scanner Settings Using the Remote InterfacePC Control Mode Clone Master Unit Slave Unit Care and Maintenance Troubleshooting Problem Suggestion Specifications Glossary of Terms Page Page Appendix Preset Fleet MapsPreset Map Block Type I Programming Information User Defined Fleet MapsSize Code Restrictions Fleet Map Size CodesNWR-SAME Event Code SVS Severe WX Reverse List BC796D Flow Charts Scan Option Conventional System Option Dimmer Uniden America Corporation One Year Limited WarrantyMemo Memo Memo