Toro 325-D, 345 manual Spindle service, Recycler Deck, Rear Discharge & Side Discharge

Page 77

TORO GM 345/325-D

Cutting Units 75

 

 

Cutting Units

Maintenance and Service

Spindle service

If noisy operation of the cutting unit is encountered and the blade spindles need to be repaired, refer to the complete repair procedures in the service manual.

The replacement bearing set consists of:

1.The upper and lower bearings races.

2.A snap ring spacer that positions the bearing races in the spindle housing.

3.An outside spacer to set the distance between the bearing races.

4.Two bearings.

5.An inside bearing spacer and an inside spacer ring.

∙The inside spacer and the spacer ring position the bearings and set the running clearance.

(NOTE: there in no groove in the shaft that the small ring sets in).

If the spindle does not rotate after assembly, verify that all the spacers and rings are properly installed.

The bearings, races, spacers and snap rings are a matched set and should not be intermixed.

IMPORTANT: If a new spindle housing is being used, new bearings and the matched snap ring set must be installed. Never use the old bearings, spacer, and snap ring with a new spindle housing. By contrast, use only new bearings with cups and spacer when installing bearings into a used spindle housing that still has a snap ring installed.

Seal replacement

When replacing the spindle seals be careful to install the seals with the seal lips facing in the correct direction.

72” Recycler Deck

1.The upper seal lip faces inward toward the upper bearing.

2.The lower seal lip faces outward, away from the lower bearing.

72” Rear Discharge & Side Discharge

1.The upper seal lip faces outward away from the upper bearing.

2.The lower seal lip faces outward, away from the lower bearing.

Notes

_______________________________________________________________________________________________________________

_______________________________________________________________________________________________________________

_______________________________________________________________________________________________________________

_______________________________________________________________________________________________________________

_______________________________________________________________________________________________________________

_______________________________________________________________________________________________________________

_______________________________________________________________________________________________________________

_______________________________________________________________________________________________________________

_______________________________________________________________________________________________________________

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Groundsmaster 345/325-D Index Product Overview Toro GM Attachments Ford VSG-411 Gas Engine Engine Identification Toro GM Checking Idle Speeds High and Low Idle ChecksToro GM Ford VSG-411 Gas Engine Correction Carburetor linkage adjustmentToro GM Ford VSG-411 Gas Engine Toro GM High Idle Adjustment Toro GM Governor Spread or Sensitivity Adjustment Anti-Surge AdjustmentToro GM Cylinder Leakage Test Compression TestingSpecial tools Review Questions Mitsubishi K3D Diesel Engine Toro GM 325-D Mitsubishi K3D Diesel Engine Analyzing Diesel Exhaust Smoke Mitsubishi K3D Diesel Engine Troubleshooting Mitsubishi K3D Diesel Engine Troubleshooting Mitsubishi K3D Diesel Engine Injection Nozzles Mitsubishi K3D Diesel Engine Toro GM 325-D Mitsubishi K3D Diesel Engine Toro GM 325-D Mitsubishi K3D Diesel Engine Glow Plug Testing Special Tools Study Questions Hydraulics Toro GM 345 / 325-D Charge Circuit Hydrostatic Drive and Hydraulic SystemsDrive circuit Drive Circuit Acceleration valves Relief Valve Acceleration valvesHydraulics Toro GM 345 / 325-D Low charge pressure Drive Pressure Test Low drive pressure. Charge pressure OK Charge Flow Test Low charge flow charge pressure OK Hydraulics Toro GM 345 / 325-D Steering Circuit Hydraulics Toro GM 345 / 325-D Cutting Unit Lift Circuit Special Tools Study Questions Electrical Systems Toro GM 345 / 325-D Start Circuit. GM 345 Shown, 325-D similar Electrical System GM 345 / 325-DInterlock Circuit Normal Operation Electrical Systems Toro GM 345 / 325-D PTO Engaged, Operator Not In The Seat Electrical Systems Toro GM 345 / 325-D Toro GM 345 / 325-D Electrical Systems Electrical Systems Toro GM 345 / 325-D Seat Switch and Traction Neutral Switch Testing Electrical Systems Toro GM 345 / 325-D Electrical circuit breaker Special Tools Helpful Hints Review Questions Cutting Unit Drive Toro GM 345 / 235-D Attachment Drive PTO Cutting Unit Drive Toro GM 345 / 235-D Troubleshooting Cutting Units Toro GM 345/325-D Rear Discharge & Side Discharge Spindle serviceRecycler Deck Cutting Units Toro GM 345/325-D Inspecting and Sharpening Rotary Mower Blades Quality Of CutCutting Units Toro GM 345/325-D Inconsistent height of cut Mismatch cutSpecial tools Helpful Hints Review Questions Commercial products

325-D, 345 specifications

The Toro 345,325-D is a highly efficient and versatile piece of turf maintenance equipment, designed primarily for golf courses, sports fields, and large landscape areas. This machine is renowned for its exceptional performance, durability, and ease of use, making it a favorite among turf management professionals.

One of the standout features of the Toro 345,325-D is its advanced engine technology. Equipped with a powerful and fuel-efficient diesel engine, it delivers impressive torque and reliability while minimizing fuel consumption. This means operators can complete their tasks efficiently without frequent refueling, a critical factor in maintaining productivity on large properties.

The Toro 345,325-D is designed with operator comfort in mind. It features a spacious, ergonomically designed operator platform that reduces fatigue during long hours of operation. The machine also boasts intuitive controls, allowing users of all skill levels to maneuver it with ease. The adjustable seat and climate control ensure that operators remain comfortable, regardless of the weather conditions.

In terms of cutting performance, the Toro 345,325-D is equipped with a high-quality cutting deck that delivers a precise and consistent cut. The deck design allows for exceptional maneuverability, even in tight spaces, ensuring that operators can maintain an immaculate appearance across a variety of terrains. With multiple cutting heights available, it caters to different turf types and aesthetic requirements.

Another key characteristic of the Toro 345,325-D is its rugged build quality. Constructed with robust materials, the machine withstands the rigors of daily use, ensuring longevity and reducing maintenance costs. Additionally, Toro's commitment to innovation includes incorporating advanced diagnostic systems to monitor the machine's health and performance, allowing for proactive maintenance and minimizing downtime.

The Toro 345,325-D is also equipped with advanced safety features, including operator presence controls and stability enhancements, which ensure safe operation on slopes and uneven ground. This level of safety not only protects the operator but also minimizes the risk of damage to the turf.

In summary, the Toro 345,325-D stands out as an industry-leading solution for turf maintenance. With its powerful engine, operator-friendly design, superior cutting performance, and robust construction, it provides unmatched reliability and efficiency. Whether for a golf course, sports field, or park, this machine is an indispensable tool for maintaining pristine landscapes. Its commitment to quality and performance makes it a preferred choice for turf management professionals worldwide.
Top Page Image Contents