Vivotek IP3111/IP3121 user manual Appendix, Post procedure

Page 85

Appendix

A. POST procedure

After the power has been turned on, NetworKam will perform a self-diagnostic to locate any possible hardware defects. If the power indicator is dim at the beginning, the power fails to proceed further. While the POST is proceeding, the status LED indicators will keep blinking interchanged until finished or any fatal error happens. If either status LED indicator is dim at the beginning, the LED may be broken.

Any possible fatal error has a special pattern shown in the following table. LED2 is the one below the network indicator and LED3 is the lowest one. If the POST is successful, status LED indicators will both shut off for a while and then light depending on the chosen network interface. If Ethernet is available, LED2 will flash like a heartbeat after network installation is done. Otherwise if modem is available, LED2 will flash alike to indicate listening for dial-in connection while LED3 is lit. If the included null modem cable is connected, both LEDs will stay on and then LED2 will start flashing after the connection from the PC is opened for configuration and LED3 stays lit.

LED pattern after POST	Possible failed component	Failed function

LED2 and LED3 blink at same time	U32(SAA7113)	Video decoder

LED2 ON and LED3 OFF	U1(TM1300)	PCI bridge of TM1300

LED2 OFF and LED3 ON	U6(RTL8139C)	Ethernet controller

LED2 ON and LED3 ON	U6(RTL8139C), U7, U8	Ethernet interface*

LED2 blink and LED3 ON	U22(M5823)	Real-time clock

LED2 ON and LED3 blink	U19(16C1550CJ), P2	COM interface

Ethernet interface failure includes not only components on board but also Ethernet cable and the

devices of the opposite end.

84

www.vivotek.com

T: 886-2-22404099

F: 886-2-22404097

Image 85

Contents NetworKam Before You Use Table of Contents How to Use Telnet Appendix Package Contents 886-2-22404099 886-2-22404097 Rear Panel Physical DescriptionEthernet 10/100 socket COM portGeneral I/O terminal block Status LEDs Power adapter Restore buttonAuto Iris Lens Connector How to Install Ethernet Environment Hardware installationCable connection Power on Easy way with installer program Software configuration886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 Manual way with existing programs First access to NetworKam 886-2-22404099 886-2-22404097 Modem Environment Cable connection Install a new modem 886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 Setup a new connection 886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 First access to NetworKam 886-2-22404099 886-2-22404097 How to Use Authentication 886-2-22404099 886-2-22404097 Main screen with camera view Primary user’s capabilityPan/Tilt positioning device control Client Setting Url http//NetworKam/client.html System configuration System parameters User group administration Network settings 886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 Video codec parameters 886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 Motion detection 886-2-22404099 886-2-22404097 Camera positioning device configuration 886-2-22404099 886-2-22404097 Modem and dialup settings 886-2-22404099 886-2-22404097 Application 886-2-22404099 886-2-22404097 Homepage layout settings One-shot fast configuration via FTP Read only string For teal For blank, 1 for default image or 2 for loading from URL Standard IP format or string shorter than 40 characters 1200k , 1000k , 768k , 512k , 384k , 256k , 128k , 64k 3, 5, 10, 15, 20, 25, 30 30 for Ntsc only Home Advanced functions Restore factory default settingsViewing system log Viewing system parametersCustomizing homepage images Uploading snapshots periodically to an external FTP serverSoftware revision upgrade Uploading the configuration file886-2-22404099 886-2-22404097 Monitor changed status of digital inputs System core debuggingStop information dumping Query status of digital inputsReset network for new settings Skip installation during the next bootReset system Set digital outputsCapture update Snapshot of Jpeg image URL commands of NetworKamClear data mode serial port driver Move motorized device in PT directionRestart system URL System configuration URL General format of command URLSystem resource URL Network configuration URL Security configuration URLVideo configuration URL Image quality configuration URL Camera custom command configuration URL Camera configuration URLApplication configuration URL Modem configuration URLHomepage layout configuration URL Appendix Post procedureFrequently asked questions 886-2-22404099 886-2-22404097 886-2-22404099 886-2-22404097 Networking Technical specificationsElectromagnetic Compatibility EMC