XiNCOM XC-DPG503 manual Management Assistant, System Information, Trap Targets

Page 38

XC-DPG503

Twin WAN VPN Gateway

Chapter Contents

SNMP

Email Alert

Syslog

Upgrade Firmware

Chapter 8 - Management Assistant

SNMP - Simple Network Management Protocol

This section is to compliment any SNMP (Simple Network Management Protocol) software installed on your PC. If you have SNMP software, you can use a standard MIB II file with the XC-DPG503.

Settings - SNMP

System Information

Contact Person - The name of the person responsible for this device

Device Name - Enter a name for the XC-DPG503

Physical Location - The location of the XC-DPG503

Trap Targets

Enter the IP address of any targets (PCs running SNMP software) to which you want traps to be sent. All traps are level 1.

Email Alert

The email alert feature will send an warning email to the system administrator and inform that one of the WAN ports was disconnected.

Email Alert

Enable – This will enable email alert to send an warning email when WAN port was disconnected.

 

 

Disable – This will disable email alert not to send an warning email when WAN port was

 

 

disconnected.

 

Email Sender Address

Email Sender Address

 

 

An email address that sends a warning email to a recipient. The warning email will inform the

 

 

recipient if there is any problem on either or both WAN ports.

 

 

Email (SMTP) Server Address

 

 

This sets the email server to where the warning email will be sent to.

 

 

For example: mail.domain.com.

 

 

Email (SMTP) server user name

 

 

This authenticates the user name of email sender (optional).

 

 

Email (SMTP) server password

38

 

This is the user password

Image 38 Contents
Twin WAN VPN Gateway Table of Contents QoS Configuration VPN Configuration Introduction Use TWO ISPs for expanded bandwidth and redundancyFeatures Http Firmware Upgrade and backup Easy SetupPassword Protected Configuration Dhcp Server SupportPhysical Details SystemDefault Settings LED Action ConditionBasic Setup Overview ProcedureNo Response? Configuring the XC-DPG503 for your LANProcedure Configuring the XC-DPG503 for your LAN Connecting two broadband modems Installation Diagram for XC-DPG503Connection Type Configuring for Internet AccessSettings Primary Setup Connection Mode Address InfoInternet Access Configure PCs on your LANTCP/IP Settings OverviewFixed IP Address For Apple ClientsFor Linux Clients To act as a Dhcp Client recommendedAdvanced Port Health Check Auto Dialup Bridge Mode Port OptionsSettings Load Balance Load BalanceSettings Advanced PPPoE Advanced PPPoESettings Advanced Pptp Advanced PptpAdvanced Setup Host IP Host IPVirtual Servers Settings Virtual ServerVirtual Servers Custom Virtual Servers Settings Custom Virtual ServersCustom Virtual Servers Server ListSpecial Application Settings Special ApplicationsSpecial Applications Dynamic DNS To use the Dynamic DNS FeatureSettings Dynamic DNS Dynamic DNSSelect the desired WAN port Multi DMZ & UPnPFor Dynamic IP Private IP AddressSettings Advanced Features Advanced FeaturesAdvanced Features Using Remote Web-based Setup HTTP// Internet IP Address of the XC-DPG503Security Management Firewall ExceptionSettings Access Filter Access FilterSettings Block URL Block URLSession Limit Settings Session LimitSession Limit & Firewall Exception QoS Configuration VPN Configuration IPSec Global Settings IPSec Global SettingPolicy Setup VPN Policy SetupKey Management Trap Targets Management AssistantSystem Information Message Status Management AssistantSyslog Configuration To save the XC-DPG503 Configuration to a file Using the Tftp Utility RecommendedUpdating the Firmware Backup your configuration To upload the firmware to the router Http Upgrade FirmwareUploading the Firmware Restoring Saved ConfigurationOperation & Status System StatusOperation & Status Advanced LAN Configuration Existing Dhcp ServerAdvanced LAN Configuration Static Routing255.255.255.0 Configuring other Routers on you LAN192.168.2.0 192.168.1.100Storage Temperature DimensionsOperating Temperature External Power AdapterUsing Dhcp TCP/IP SettingsChecking TCP/IP Settings Windows 9x/ME Using Specify an IP AddressChecking TCP/IP Settings Windows Using a fixed IP Address Use the following IP AddressChecking TCP/IP Settings Windows XP Figure G. Network Configuration Windows XPTroubleshooting Overview