3M 800r3 manual Installation and Set-Up, Receiving And Handling, Uncrated

Page 15

Installation and Set-Up

Receiving And Handling

After the machine has been uncrated, examine the case sealer for damage that might have occurred during transit. If damage is evident, file a damage claim immediately with the transportation company and also your 3M Representative.

Machine Set-Up

Important – Read "Warnings" on page 17 before attempting to set-up the case sealer for operation.

The following instructions are presented in the order recommended for setting up and installing the case sealer. Following them step by step will result in an installation in your production line that best utilizes the many features built into the case sealer. Refer to Figures 3-1 and 3-2 to identify the various components of the case sealer.

Note – A tool kit consisting of metric open end and hex socket wrenches is provided with the machine. These tools should be adequate to set- up the machine, however, other tools supplied by the customer will be required for machine mainte- nance.

PACKAGING AND SEPARATE PARTS

1.Lift off fiberboard cover off pallet after removing staples at bottom.

2.Remove protective wrapping around machine.

3.Remove hardware that secures case sealer legs to pallet.

4.Cut cable ties that secure upper assembly to machine bed on each side of machine. Remove and discard cable ties and foam blocks.

5.Ensure that the tape drum bracket assembly, located on the lower taping head, is mounted straight down, as shown in Figure 2-1A. The tape drum bracket assembly can be pivoted to provide tape roll clearance in certain cases.

6.Use appropriate material handling equipment to remove the machine from the pallet and move it into position.

CAUTION – Machine weighs approximately 208 kg [460 pounds]

uncrated.

7.Adjust machine bed height. The case sealer is equipped with four adjustable legs that are located at the corners of the machine frame. The legs can be adjusted to obtain different machine bed heights from 510 mm [20 in] minimum to 690 mm [27.25 in] maximum.

Note –Minimum machine bed height can be reduced to 400 mm [15.75 inch] by moving outer columns up one set of mounting holes. However, this change also reduces minimum box height of 127 mm [5.00 inch] to 232 mm [9.12 inch]. (See "Special Set-Up Procedure

– Outer Column Re-positioning", page 24.)

Refer to Figure 2-1C and set the machine bed height as follows:

a.Use appropriate material handling equipment and blocking techniques to raise the machine frame to allow adequate leg adjustment.

b.Loosen, but do not remove, two M8 x 16 socket head screws in one leg (use M6 hex wrench). Adjust the leg length for the desired machine bed height. Retighten the two screws to secure the leg. Adjust all four legs equally.

10

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 3M-Matic To Our Customers Replacement Parts and Additional ManualsTo Our Customers Table of Contents Section II AccuGlide II STD 3-Inch Taping Head 3M-MaticTM800r3 Random Case Sealer, Type Intended Use800r3 Contents Knife Warning Label Important SafeguardsOperating Notice Label 10 -Air Pressure Gage Label 11 Knife Warning Label 12 Tape Threading LabelSpecifications Box Size Box Weight and Size Capacities WeightMaximum Machine Dimensions MinimumInstallation and Set-Up Receiving And HandlingUncrated BOX Size Capacity of Case Sealer Pneumatic Connection Case Sealer Components OperationMain Air On/Off Valve/Pressure Regulator/ Filter Figure Controls, Valves and Switches Electrical On/Off SwitchDoor Air Pressure Regulator, Box Drive Belt Centering -4Air Pressure Gauge, Upper Taping Head Frame Main Air Pressure Gauge Latching Knob, Upper Taping Head Frame -FigureBox Exit Cams See Section II, pages 7 Operation Box SealingLubrication MaintenanceBox Drive Belt Left Side View Infeed End Box Drive Assembly, Infeed End Personnel could result Circuit Breaker Knife Replacement, Taping HeadAdjustments Taping Head Adjustments Refer to SectionPersonnel could result Drive Belt Tension Special Set-Up Procedure Column Re-Positioning This page is Blank Troubleshooting Guide Problem Cause Correction TroubleshootingTroubleshooting 800r3 Case Sealer Operating Sequence Electrical Diagram Electrical/Pneumatic DiagramsPage Pneumatic Diagram Page This page is Blank Parts and Service Information Part Number Option/Accessory Options/AccessoriesReplacement Parts Illustrations and Parts Lists This page is Blank 800r3 Random Case Sealer Frame Assemblies 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Safety and Information Labels Ref. No 3M Part No Description Qty 800r3 Safety and Information Labels

800r3 specifications

The 3M 800R3 is a cutting-edge respiratory protection system designed for those who work in environments where they may encounter hazardous airborne contaminants. This respiratory mask is part of 3M’s extensive line of personal protective equipment and is engineered for comfort, performance, and reliability.

One of the main features of the 3M 800R3 is its advanced filter technology, which ensures effective filtration of organic vapors and particulates. It is equipped with a P100 filter, which provides a minimum efficiency of 99.97% against airborne particles, making it ideal for use in various industries, including construction, healthcare, and chemical processing. This level of protection is essential for workers who need to protect their respiratory systems from harmful substances.

The 3M 800R3 employs a unique multi-layered filtration system. This includes an activated carbon layer that absorbs certain gases and vapors, providing an added level of safety. This technology enhances the overall user experience by reducing the inhalation of noxious chemicals, thereby ensuring better worker health and increasing productivity.

Comfort and fit are paramount in any respiratory protective system, and the 3M 800R3 does not disappoint. The mask features an ergonomic design with adjustable straps, allowing users to achieve a secure and comfortable fit. Its lightweight material reduces fatigue during extended wear, making it suitable for long shifts in demanding environments. Additionally, the flexible facepiece conforms to various face shapes, ensuring a good seal without compromising comfort.

Another notable characteristic of the 3M 800R3 is its versatility. It can be used with a range of cartridges and filters, allowing users to customize their level of protection based on specific job requirements. This adaptability makes it an excellent choice for workers who face different hazards throughout their workday.

The 3M 800R3 is also designed for easy maintenance and cleaning. Its washable components ensure longevity and hygiene, while the replaceable filters reduce waste and operating costs, making it an economical choice for employers and safety professionals.

In summary, the 3M 800R3 is a formidable respiratory protection device that combines advanced filtration technology, comfort, and versatility. It is an essential tool for safeguarding respiratory health in various workplaces, ensuring users have the necessary protection from airborne hazards.
Top Page Image Contents