3M 800r3 manual Special Set-Up Procedure

Page 29

Special Set-Up Procedure

WARNING – Turn air supply and electrical power off and disconnect

power cord from power supply before beginning special set-up procedure. If power cord is not disconnected, severe injury to personnel could result.

Changing the Tape Leg Length (From 70 to 50 mm [2.75 to 2.00 in])

Changing tape leg length to 50 mm [2 in] allows taping of smaller boxes. Refer to "Specifications – Box Weight and Size Capacities", page 8 for box sizes.

CASE SEALER FRAME

No changes required.

TAPING HEADS

WARNING – Use care when working near taping head knives as knives

are extremely sharp. If care is not taken, severe injury to personnel could result.

1.Remove upper taping head. Loosen and remove four (each) M6 x 25 flat head screws (A), special washers (B) and spacers (C) that fasten head to upper assembly as shown in Figure 5-1. Support or hold taping head to keep it from falling when screws are removed.

2.Turn air supply on and raise and latch upper assembly in full up position. Turn air supply off.

WARNING –The E-Stop switch or door must not be used for raising

the upper head assembly for maintenance work. If these are used the upper head assembly could lower during maintenance work causing injury to personnel.

3.Remove lower taping head by pulling straight up.

4.Refer to Section II "Adjustments – Changing Tape Leg Length", page 13.

Figure 5-1 – Upper Taping Head Mounting

Outer Column – Re-Positioning

WARNING – It is recommended that no less than two people assist on

this set-up or severe injury or equipment damage could result.

Moving the outer columns to the upper set of mounting holes, increases the maximum box size (height) handled by the case sealer from 533 mm [21.00 in] to 644 mm [25.38 in]. (Dimensions given are with lift cylinders mounted in standard position.)

Note – This also increases the minimum box height from 127 mm [5.00 in] to 232 mm [9.12 in].

Refer to Figure 5-2

1.With air on, raise and latch upper assembly in full raised position. Be sure electrical supply is disconnected.

2.Place solid blocks 495 to 535 mm [19.5 to 21.0 in] high under front and back of upper assembly as shown in Figure 5-2A.

24

Page 28 Page 30
Image 29
Page 28 Page 30
Contents 3M-Matic To Our Customers Replacement Parts and Additional ManualsTo Our Customers Table of Contents Section II AccuGlide II STD 3-Inch Taping Head 3M-MaticTM800r3 Random Case Sealer, Type Intended Use800r3 Contents Knife Warning Label Important SafeguardsOperating Notice Label 10 -Air Pressure Gage Label 11 Knife Warning Label 12 Tape Threading LabelSpecifications Box Size Box Weight and Size Capacities WeightMaximum Machine Dimensions MinimumUncrated Installation and Set-UpReceiving And Handling BOX Size Capacity of Case Sealer Pneumatic Connection Case Sealer Components OperationMain Air On/Off Valve/Pressure Regulator/ Filter Figure Controls, Valves and Switches Electrical On/Off SwitchAir Pressure Gauge, Upper Taping Head Frame DoorAir Pressure Regulator, Box Drive Belt Centering -4 Box Exit Cams Main Air Pressure GaugeLatching Knob, Upper Taping Head Frame -Figure See Section II, pages 7 Operation Box SealingLubrication MaintenanceBox Drive Belt Left Side View Infeed End Box Drive Assembly, Infeed End Personnel could result Circuit Breaker Knife Replacement, Taping HeadPersonnel could result Drive Belt Tension AdjustmentsTaping Head Adjustments Refer to Section Special Set-Up Procedure Column Re-Positioning This page is Blank Troubleshooting Guide Problem Cause Correction TroubleshootingTroubleshooting 800r3 Case Sealer Operating Sequence Electrical Diagram Electrical/Pneumatic DiagramsPage Pneumatic Diagram Page This page is Blank Parts and Service Information Part Number Option/Accessory Options/AccessoriesReplacement Parts Illustrations and Parts Lists This page is Blank 800r3 Random Case Sealer Frame Assemblies 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Ref. No 3M Part No Description 800r3 Random Case Sealer Safety and Information Labels Ref. No 3M Part No Description Qty 800r3 Safety and Information Labels

800r3 specifications

The 3M 800R3 is a cutting-edge respiratory protection system designed for those who work in environments where they may encounter hazardous airborne contaminants. This respiratory mask is part of 3M’s extensive line of personal protective equipment and is engineered for comfort, performance, and reliability.

One of the main features of the 3M 800R3 is its advanced filter technology, which ensures effective filtration of organic vapors and particulates. It is equipped with a P100 filter, which provides a minimum efficiency of 99.97% against airborne particles, making it ideal for use in various industries, including construction, healthcare, and chemical processing. This level of protection is essential for workers who need to protect their respiratory systems from harmful substances.

The 3M 800R3 employs a unique multi-layered filtration system. This includes an activated carbon layer that absorbs certain gases and vapors, providing an added level of safety. This technology enhances the overall user experience by reducing the inhalation of noxious chemicals, thereby ensuring better worker health and increasing productivity.

Comfort and fit are paramount in any respiratory protective system, and the 3M 800R3 does not disappoint. The mask features an ergonomic design with adjustable straps, allowing users to achieve a secure and comfortable fit. Its lightweight material reduces fatigue during extended wear, making it suitable for long shifts in demanding environments. Additionally, the flexible facepiece conforms to various face shapes, ensuring a good seal without compromising comfort.

Another notable characteristic of the 3M 800R3 is its versatility. It can be used with a range of cartridges and filters, allowing users to customize their level of protection based on specific job requirements. This adaptability makes it an excellent choice for workers who face different hazards throughout their workday.

The 3M 800R3 is also designed for easy maintenance and cleaning. Its washable components ensure longevity and hygiene, while the replaceable filters reduce waste and operating costs, making it an economical choice for employers and safety professionals.

In summary, the 3M 800R3 is a formidable respiratory protection device that combines advanced filtration technology, comfort, and versatility. It is an essential tool for safeguarding respiratory health in various workplaces, ensuring users have the necessary protection from airborne hazards.
Top Page Image Contents