Panasonic CF-VDL02BM General Events, Windows, Devices Calibration, Hardware, Settings, Status

Page 11

Configuring the Touchscreen

When needed, the touchscreen can be configured using the following steps.

1Windows XP

Select from the taskbar and select [Adjust settings], or select [Settings] from [start] - [All Programs] - [UPDD]

Windows 2000

Select from the taskbar and select [Adjust settings], or select [Settings] from [Start] - [Programs] - [UPDD]

The following screen will be displayed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

General

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Events

 

 

 

 

 

 

 

 

 

 

 

 

 

Set the general settings and functions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

Set the events that can

 

 

 

 

 

Windows

 

 

 

 

 

 

 

be generated by a controller.

 

 

 

 

 

Set the “double-click” settings.

 

 

 

 

Devices

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Calibration

 

 

Configure

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Define the calibration setup.

 

the device controller.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use when the cursor can not

 

Hardware

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

be pointed correctly with the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

finger or stylus. (Needed if

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Set the hardware

 

 

 

 

 

 

 

 

the alignment of

the

 

resources. Make

 

 

 

 

 

 

 

 

touchscreen with the visual

sure that this set-

 

 

 

 

 

 

 

 

image change or adjust the

ting matches the

 

 

 

 

 

 

 

 

display resolution).

 

 

[Serial Port] to

 

 

 

 

 

 

 

 

<Only for CF-M34 series

which the LCD

 

 

 

 

 

 

 

 

models other than the CF-

monitor has been

 

 

 

 

 

 

 

 

M34C******>

 

 

connected as set

 

 

 

 

 

 

 

 

Before you run the calibra-

using the Setup

 

 

 

 

 

 

 

 

tion, you need to set the de-

Utility.

 

 

 

 

 

 

 

 

 

 

 

 

vice at [Calibration Settings

 

 

 

 

 

 

 

 

For] as followings.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Settings

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[Device 1] is for the com-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

puter

 

 

Set the general protocol

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[Device 2] is for the LCD

settings.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Monitor

 

 

Advanced

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

About

 

 

Set the advanced settings.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Display the version number.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE

 

 

 

 

Status

 

 

 

 

 

 

 

 

For more information, refer to [Help].

 

 

 

 

Display the status of the controller.

11

Image 11
Contents CF-VDL02BM English When DrivingWhen Operating When Car WashingWhen Parked For InstallationPS/2 Cable Function Cable IntroductionLCD Monitor Operating Instructions Sun Shade LCD Names and Functions of PartsMounting the LCD Monitor Mount the LCD Monitor Attach the cover of the LCD MonitorMount the Sun Shade Confirm shut down Windows XP Press the power switch of the LCD MonitorStarting Up/Shutting Down Select your applicationDragging TouchscreenMoving the cursor Cursor Clicking Double-clicking Touchscreen Devices Calibration SettingsGeneral Events WindowsWindows XP Make necessary changes Select OKIcon Function Description Adjusting the LCD MonitorPress OSD main menuRGB Auto Center PhasePosition ImageMiscellaneous Auto PhaseAuto Configuration OSD TimeoutIng on TroubleshootingTroubleshooting XGA SpecificationsVGA SvgaLors de la conduite FrançaisRecours au Support technique Panasonic Pour l’installationLors du lavage du véhicule En stationnementCâble PS/2 Câble de fonction Moniteur LCD Instructions d’utilisation Pare-soleilNoms et fonctions des pièces Montage du Moniteur LCD Montez le Moniteur LCD à travers ces trous pour vis M4 Montez le Moniteur LCDConfirmez l’arrêt Windows XP Mise en marche/ArrêtAppuyez sur le commutateur d’alimentation du Moniteur LCD Sélectionnez l’applicationÉcran tactile Déplacement du curseur Cliquage Curseur Double cliquageDéplacement Écran tactile General AdvancedPage Icone Fonction Description Réglage du Moniteur LCDAppuyez sur Menu principal OSDRGB RVB Réglage du Moniteur LCDPosition Init NVRam Information Dépannage ’affiche Spécifications Memo DFQX5547ZA