Panasonic PT-AE3000E manual Important Safety Notice, Important the Moulded Plug U.K. only

Page 3

Important Safety Notice

Pursuant to at the directive 2004/108/EC, article 9(2)

Panasonic Testing Centre

Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, F.R. Germany

IMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark a or the BSI mark ` on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorised Service Centre.

If the fitted moulded plug is unsuitable for the mains socket in your home, then the fuse should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below.

If in any doubt, please consult a qualified electrician.

WARNING: THIS APPLIANCE MUST BE EARTHED.

Important Information

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Green - and - Yellow:

Earth

Blue:

Neutral

Brown:

Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol W or coloured GREEN or GREEN - AND -

YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

BS1363/A

N

13A250V

-8

 

 

HE

L

 

ASA

 

ENGLISH - 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Operating Instructions To rain or moisture Important Safety NoticeFor business users in the European Union This Apparatus Must be EarthedImportant the Moulded Plug U.K. only Important Safety NoticeContents Lens Control ContentsMenu Navigation Picture menuPrecautions with regard to safety Precautions with regard to safety Do not set up the projector outdoorsDo not look into the lens while the projector is being used Do not mix old and new batteries Remove the used batteries from the remote control promptlyDo not put your weight on this projector Use only the specified batteriesLiquid crystal panel Projector may be subject to electromagnetic interferenceOrder to get the best picture quality Do not touch the surfaces of the lens with your bare handsMains lead for UK AccessoriesRemote control for Safety cable Lens cover PT-AE3000E TTRA0141About Your Projector Remote controlProjector body About Your ProjectorTop and front view Component About Your Projector Back and bottom viewComputer HdmiSetting up Calculation methods for screen dimensionsScreen size and throw distance Mounting on the ceiling and projecting from front Front leg adjusters and throwing angleSetting up Projection methodVertical shift Adjusting the lens shift dialsLens shift and positioning Horizontal shift100% 40% Setting up Projector location rangeWhen the screen position is fixed When the projector position is fixedConnections Before connecting to the projectorConnecting example Component IN/S-VIDEO Connecting example Hdmi IN/COMPUTERConnect the mains lead to a mains socket Switching the projector on/offConnecting Mains leadPower indicator Switching the projector on/offPower indicator informs you the status of the power Switching on the projector Switching off the projectorPress I to select OK and press the power or Enter button Projecting an image Selecting the input signalSwitch on the connected devices Adjust the focus and the projected image sizeAdjusting the image Remote control operationManaging the lens control settings Switching the picture modeRemote control operation Loading a saved settingSwitching the aspect ratio Adjusting the signal condition with a waveformContrast G/CONTRAST B Adjustment exampleAdjusting with luminance options Adjusting with RGB optionsManaging stored logs Setting your own colour profileAdjusting the selected colour Create a new profileLoading saved profiles Saving a log setting as a profileDeleting the saved profiles Changing the profile namesCapturing an image Resetting to the factory default settingsSwitching the input signal Using the assigned function as shortcutDisplaying the main menu Adjusting with the bar scale itemsMenu Navigation Navigating through the MenuMenu Navigation Main menu and sub-menuLanguage Lens Control Picture menu Waveform Monitor Colour TemperatureSplit Adjust Dynamic IrisNR Noise Reduction Adjusting the image in a split windowColour Memory Edit Signal ModeMemory Save Memory LoadDOT Clock Clock PhasePosition menu PositionFIT Component signalsPosition menu Aspect ratio options and projection example ZoomKeystone Auto SetupWSS Over ScanLens Memory Save Adjust ZOOM/FOCUS, H-AREA PositionZOOM/FOCUS Lens Memory LoadYou can edit named lens memory settings Rename the lens memory settingLens Memory Edit Assignable functions Underlined item is factory default settingButton Blank functionOption menu Sleep InstallationHigh Altitude Mode Lamp PowerTemp indicator Temp and Lamp IndicatorsManaging the indicated problems Lamp indicatorCleaning the projector Care and ReplacementBefore replacing the lamp unit Care and ReplacementWhen to replace the lamp unit Replacing the lamp unitCare and Replacement Removing and replacing the lamp unit Resetting the Lamp RuntimeAttaching the top cover Troubleshooting Dots *1 MHz KHz List of compatible signalsTechnical Information Quality *2Serial terminal Control commands Technical Information Communication settingsInquiry commands Specifications Hdmi VideoComputer ComponentCeiling mount bracket safeguards Installing the safety cableLoop twice Loop once Dimensions Trademark acknowledgementsUnit mm Index Control panel button Indicator status Remote control buttonIndex Main menu
Top Page Image Contents