Panasonic PT-AE3000E Temp and Lamp Indicators, Managing the indicated problems, Lamp indicator

Page 45

TEMP and LAMP Indicators

Managing the indicated problems

If a problem should occur with the projector, the LAMP and/or TEMP

 

indicators will inform you. Manage the indicated problems as follows.

 

1.

Confirm the status of all indicators and projector, and switch off

 

 

the projector in proper way.

 

2.

Find out the cause of the problem by status of the LAMP and/or

Power LAMP TEMP

 

TEMP indicators.

 

 

3.Follow the following instruction for each indication and solve the problem.

4.Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer.

LAMP indicator

Indicator

Illuminating red

Flashing red

 

 

 

 

 

 

 

Problem

LAMP RUNTIME has

Lamp circuit failure, abnormal function or lamp unit is damaged.

reached 1 800 hours.

 

 

 

 

 

The lamp unit will run out

The MAIN POWER is

 

 

Cause

switched on again before

Lamp circuit failure,

The lamp unit is

soon and needs to be

the lamp unit is cooled

abnormal function.

damaged.

 

replaced.

 

enough.

 

 

 

 

 

 

 

 

Let the lamp unit cool

 

 

Remedy

See “Replacing the lamp

down and turn on the

Contact an Authorised

See “Replacing the lamp

unit” on page 47.

MAIN POWER after

Service Centre.

unit” on page 47.

 

 

 

90 seconds.

 

 

 

 

 

 

 

TEMP indicator

Indicator

Illuminating red while projecting and the alert will be displayed.

 

Flashing red and the power button is turned off.

 

 

 

 

 

Problem

The temperature inside and/or outside the projector is abnormally high.

 

 

 

 

 

 

Cause

The ventilation openings

The room temperature is

The air filter is excessively

The projector is located at

dirty and the ventilation is

high elevations (above

are covered.

too high.

 

poor.

1 400 - 2 700 m).

 

 

 

 

Remove the object(s)

Reinstall the projector in a

Replace the air filter in the

Turn on the projector and

Remedy

from the ventilation

set the HIGH ALTITUDE

openings or clear around

temperature controlled

proper method. See

MODE to ON.

 

place. See page 54.

page 46.

 

the projector.

See page 44.

 

 

 

 

 

 

 

 

NOTE:

• If no problem is found or the problem remains, do not turn on the projector. Instead contact an Authorised Service Centre.

Maintenance

ENGLISH - 45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Operating Instructions For business users in the European Union Important Safety NoticeThis Apparatus Must be Earthed To rain or moistureImportant the Moulded Plug U.K. only Important Safety NoticeContents Menu Navigation ContentsPicture menu Lens ControlPrecautions with regard to safety Precautions with regard to safety Do not set up the projector outdoorsDo not look into the lens while the projector is being used Do not put your weight on this projector Remove the used batteries from the remote control promptlyUse only the specified batteries Do not mix old and new batteriesOrder to get the best picture quality Projector may be subject to electromagnetic interferenceDo not touch the surfaces of the lens with your bare hands Liquid crystal panelRemote control for Safety cable Lens cover AccessoriesPT-AE3000E TTRA0141 Mains lead for UKAbout Your Projector Remote controlProjector body About Your ProjectorTop and front view Computer About Your Projector Back and bottom viewHdmi ComponentSetting up Calculation methods for screen dimensionsScreen size and throw distance Setting up Front leg adjusters and throwing angleProjection method Mounting on the ceiling and projecting from frontLens shift and positioning Adjusting the lens shift dialsHorizontal shift Vertical shiftWhen the screen position is fixed Setting up Projector location rangeWhen the projector position is fixed 100% 40%Connecting example Component IN/S-VIDEO Before connecting to the projectorConnecting example Hdmi IN/COMPUTER ConnectionsConnecting Switching the projector on/offMains lead Connect the mains lead to a mains socketPower indicator Switching the projector on/offPower indicator informs you the status of the power Switching on the projector Switching off the projectorPress I to select OK and press the power or Enter button Switch on the connected devices Selecting the input signalAdjust the focus and the projected image size Projecting an imageManaging the lens control settings Remote control operationSwitching the picture mode Adjusting the imageSwitching the aspect ratio Loading a saved settingAdjusting the signal condition with a waveform Remote control operationAdjusting with luminance options Adjustment exampleAdjusting with RGB options Contrast G/CONTRAST BAdjusting the selected colour Setting your own colour profileCreate a new profile Managing stored logsDeleting the saved profiles Saving a log setting as a profileChanging the profile names Loading saved profilesSwitching the input signal Resetting to the factory default settingsUsing the assigned function as shortcut Capturing an imageMenu Navigation Adjusting with the bar scale itemsNavigating through the Menu Displaying the main menuMenu Navigation Main menu and sub-menuLanguage Lens Control Picture menu Split Adjust Colour TemperatureDynamic Iris Waveform MonitorNR Noise Reduction Adjusting the image in a split windowColour Memory Save Signal ModeMemory Load Memory EditPosition menu Clock PhasePosition DOT ClockPosition menu Aspect ratio options and projection example Component signalsZoom FITWSS Auto SetupOver Scan KeystoneZOOM/FOCUS Adjust ZOOM/FOCUS, H-AREA PositionLens Memory Load Lens Memory SaveYou can edit named lens memory settings Rename the lens memory settingLens Memory Edit Button Underlined item is factory default settingBlank function Assignable functionsOption menu High Altitude Mode InstallationLamp Power SleepManaging the indicated problems Temp and Lamp IndicatorsLamp indicator Temp indicatorCleaning the projector Care and ReplacementWhen to replace the lamp unit Care and ReplacementReplacing the lamp unit Before replacing the lamp unitCare and Replacement Removing and replacing the lamp unit Resetting the Lamp RuntimeAttaching the top cover Troubleshooting Technical Information List of compatible signalsQuality *2 Dots *1 MHz KHzSerial terminal Control commands Technical Information Communication settingsInquiry commands Specifications Computer VideoComponent HdmiCeiling mount bracket safeguards Installing the safety cableLoop twice Loop once Dimensions Trademark acknowledgementsUnit mm Index Index Indicator status Remote control buttonMain menu Control panel button
Top Page Image Contents