Panasonic PT-AX200E manual Care and Replacement Removing and replacing the lamp unit

Page 43

Care and Replacement

Removing and replacing the lamp unit

1.Turn the projector upside down and place it gently on a soft cloth.

2.Use a Phillips screw driver to loosen the 2 lamp unit fixing screws until the screws turn freely and remove the lamp unit cover.

3.Use a Phillips screw driver to loosen the 2 lamp unit fixing screws until the screws turn freely.

4.Hold the handle of the lamp unit and pull out gently from the projector.

5.Replace the new lamp unit while making sure that the direction of insertion is correct.

Press the top of the lamp unit and make sure the unit is installed securely.

6.Tighten the lamp unit fixing screws securely with a Phillips screwdriver.

7.Attach the lamp unit cover and tighten the 3 lamp unit cover fixing screws securely with a Phillips screw driver.

Lamp unit cover fixing screws

Lamp unit cover

Lamp unit fixing screws

Press here

Press here

Handle

NOTE:

• Be sure to install the lamp unit and attach the lamp unit cover securely. If they are not installed securely, it may cause the protection circuit to operate so that the power cannot be turned on.

• Grip the handle and keep the lamp unit paralleled when you remove the lamp unit. Some parts of the lamp unit are sharpened and may cause injury.

• Do not switch the power on while the lamp unit cover removed.

Resetting the LAMP RUNTIME

 

If the lamp usage time has passed 2 000 hours (when LAMP POWER has been set to NORMAL), the

 

 

projector will switch to standby mode after approximately 10 minutes of operation. The resetting procedure

 

 

should thus be completed within 10 minutes.

6.

Press and hold the ENTER button for

 

1.

Connect the mains lead to the projector and a

 

 

mains socket, and switch the MAIN POWER on.

 

approximately 3 seconds.

 

2.

Press the POWER button.

7.

The confirmation screen will be displayed and

 

3.

Press the MENU button to display the menu.

 

select OK.

 

4.

Select the OPTION menu and press the ENTER

8.

Press the POWER button to turn off for resetting

 

 

button.

 

the duration of the LAMP RUNTIME.

 

5.

Select LAMP RUNTIME.

9.

Confirm the duration of time in LAMP RUNTIME is

 

 

 

 

 

 

 

 

 

 

 

reset to “0 H”.

Maintenance

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGLISH - 43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Operating Instructions To rain or moisture Important Safety NoticeFor business users in the European Union This Apparatus Must be EarthedImportant the Moulded Plug U.K. only Important Safety NoticeContents Position menu ContentsMenu Navigation Picture menuPrecautions with regard to safety Use only the specified batteries Precautions with regard to safetyDo not set up the projector outdoors Do not look into the lens while the projector is being usedElectric shocks can result if this is not done Remove the used batteries from the remote control promptlyDo not put your weight on this projector Do not mix old and new batteriesScreen Order to get the best picture qualityDo not touch the surfaces of the lens with your bare hands Liquid crystal panelMains lead for UK AccessoriesAbout Your Projector Remote controlAbout Your Projector Projector bodyTop and front view About Your Projector Back and bottom view Projected image Setting upCalculation methods for screen dimensions Screen size and throw distanceMounting in the ceiling and projecting from front Front leg adjusters and throwing angleSetting up Projection methodVertical shift Adjusting the lens shift leverLens shift and positioning Horizontal shift63% Setting up Projector location rangeWhen the screen position is fixed When the projector position is fixedConnections Before connecting to the projectorConnecting to Component IN/VIDEO IN/S-VIDEO Connecting to Computer IN/HDMIMains lead Switching the projector on/offPower indicator ConnectingSwitching off the projector Switching on the projectorSwitching the projector on/off Projecting an image Selecting the input signalSwitch on the connected devices Adjust the focus and the projected image sizeTurning on the button backlight Remote control operationSwitching the preset settings Operating rangeRemote control operation Adjusting the imageSwitching the aspect ratio Resetting to the factory default settingsBrightness Setting your own colour profileAdjusting the selected colour Managing stored logsDeleting the saved profiles Saving a log setting as a profileChanging the profile names Loading saved profilesAssigning the functions for shortcut Switching the input signalComponent Video Computer Hdmi 1 Hdmi 2 Navigating through the Menu Menu NavigationDisplaying the main menu Main menu and sub-menu DefaultMenu Navigation Aspect Clock Phase *2Position DOT Clock *1Picture menu Advanced Menu Colour TemperatureDynamic Iris Light HarmonizerFavourite Load Favourite SaveYou can edit the named memory settings Signal ModeDeleting a memory setting Changing the name of the memory settingDOT Clock Clock PhasePosition menu PositionScroll Component signalsComputer signals Position menu Aspect ratio options and projection exampleKeystone Auto SetupWSS Over ScanFunction Button Remote controlBlank function Option menu Test Pattern Lamp PowerSleep Lamp Runtime Temp indicator Temp and Lamp Indicators Managing the indicated problems Lamp indicatorCleaning the projector Care and ReplacementBefore replacing the lamp unit Care and ReplacementWhen to replace the lamp unit Replacing the lamp unitResetting the Lamp Runtime Care and Replacement Removing and replacing the lamp unitSelect Lamp Runtime Troubleshooting Technical Information List of compatible signalsSerial terminal Control commands Technical Information Communication settingsInquiry Commands Specifications Hdmi VideoComputer ComponentInstalling the safety cable Ceiling mount bracket safeguardsTrademark acknowledgements DimensionsUnit mm Index Main menu Navigation Sub-menu Accessory ConnectingAccessory Screen size Calculation methods Security lock IndexS0807-0A
Related manuals
Manual 54 pages 35.04 Kb
Top Page Image Contents