Panasonic PT-AX200E manual Precautions with regard to safety, Do not set up the projector outdoors

Page 7

Precautions with regard to safety

Do not use the projector in a bath or shower. Fire or electric shocks can result.

Do not place your skin into the light beam while the projector is being used.

Strong light is emitted from the projector’s lens. If you place directly into this light, it can hurt or damage your skin.

Do not look into the lens while the projector is being used.

Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.

Be especially careful not to let young children look into the lens. In addition, turn off the power and disconnect the mains plug when you are away from the projector.

Do not place your hands or other objects close to the air outlet port.

Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port [allow at least

50 cm (20") of space], otherwise burns or damage could result.

CAUTIONS

Replacement of the lamp is recommended to be carried out by a qualified technician.

The lamp has high internal pressure. If improperly handled, explosion might result.

The lamp can easily become damaged if struck against hard objects or dropped, and injury or malfunctions may result.

When replacing the lamp, allow it to cool for at least one hour before handling it.

The lamp cover gets very hot, and touching it can cause burns.

Before replacing the lamp, be sure to disconnect the mains plug from the mains socket.

Electric shocks or explosions can result if this is not done.

Do not allow infants or pets to touch the remote control unit.

Keep the remote control unit out of the reach of infants and pets after using it.

Important Information

Do not cover the air inlet port or the air outlet port. Doing so may cause the projector to overheat, which can cause fire or damage to the projector.

Do not place the projector in narrow, badly ventilated places such as closets or bookshelves.

Do not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.

Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam.

Using the projector under such conditions may result in fire, electric shocks or plastic deterioration. The plastic deterioration may cause the falling down of the projector which is mounted in the ceiling.

Do not set up the projector in a high temperature environment, such as near a heater or in direct sunlight.

Failure to observe this may result in fire, malfunction or plastic deterioration.

Do not set up the projector outdoors.

The projector is designed for indoor use only.

When disconnecting the mains lead, hold the plug, not the lead.

If the mains lead itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur.

Do not place any heavy objects on top of the projector.

Failure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury.

Do not short-circuit, heat or disassemble the batteries or place them into water or fire.

Failure to observe this may cause the batteries to overheat, leak, explode or catch fire, and burns or other injury may result.

When inserting the batteries, make sure the polarities (+ and -) are correct.

If the batteries are inserted incorrectly, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.

Use only the specified batteries.

If incorrect or different kind of batteries are used, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.

ENGLISH - 7

Image 7
Contents Operating Instructions To rain or moisture Important Safety NoticeFor business users in the European Union This Apparatus Must be EarthedImportant the Moulded Plug U.K. only Important Safety NoticeContents Position menu ContentsMenu Navigation Picture menuPrecautions with regard to safety Use only the specified batteries Precautions with regard to safetyDo not set up the projector outdoors Do not look into the lens while the projector is being usedElectric shocks can result if this is not done Remove the used batteries from the remote control promptlyDo not put your weight on this projector Do not mix old and new batteriesScreen Order to get the best picture qualityDo not touch the surfaces of the lens with your bare hands Liquid crystal panelMains lead for UK AccessoriesAbout Your Projector Remote controlAbout Your Projector Projector bodyTop and front view About Your Projector Back and bottom view Projected image Setting upCalculation methods for screen dimensions Screen size and throw distanceMounting in the ceiling and projecting from front Front leg adjusters and throwing angleSetting up Projection methodVertical shift Adjusting the lens shift leverLens shift and positioning Horizontal shift63% Setting up Projector location rangeWhen the screen position is fixed When the projector position is fixedConnections Before connecting to the projectorConnecting to Component IN/VIDEO IN/S-VIDEO Connecting to Computer IN/HDMIMains lead Switching the projector on/offPower indicator ConnectingSwitching off the projector Switching on the projectorSwitching the projector on/off Projecting an image Selecting the input signalSwitch on the connected devices Adjust the focus and the projected image sizeTurning on the button backlight Remote control operationSwitching the preset settings Operating rangeRemote control operation Adjusting the imageSwitching the aspect ratio Resetting to the factory default settingsBrightness Setting your own colour profileAdjusting the selected colour Managing stored logsDeleting the saved profiles Saving a log setting as a profileChanging the profile names Loading saved profilesAssigning the functions for shortcut Switching the input signalComponent Video Computer Hdmi 1 Hdmi 2 Navigating through the Menu Menu NavigationDisplaying the main menu Main menu and sub-menu DefaultMenu Navigation Aspect Clock Phase *2Position DOT Clock *1Picture menu Advanced Menu Colour TemperatureDynamic Iris Light HarmonizerFavourite Load Favourite SaveYou can edit the named memory settings Signal ModeDeleting a memory setting Changing the name of the memory settingDOT Clock Clock PhasePosition menu PositionScroll Component signalsComputer signals Position menu Aspect ratio options and projection exampleKeystone Auto SetupWSS Over ScanFunction Button Remote controlBlank function Option menu Test Pattern Lamp PowerSleep Lamp RuntimeTemp indicator Temp and Lamp IndicatorsManaging the indicated problems Lamp indicatorCleaning the projector Care and ReplacementBefore replacing the lamp unit Care and ReplacementWhen to replace the lamp unit Replacing the lamp unitResetting the Lamp Runtime Care and Replacement Removing and replacing the lamp unitSelect Lamp Runtime Troubleshooting Technical Information List of compatible signalsSerial terminal Control commands Technical Information Communication settingsInquiry Commands Specifications Hdmi VideoComputer ComponentInstalling the safety cable Ceiling mount bracket safeguardsTrademark acknowledgements DimensionsUnit mm Index Main menu Navigation Sub-menu Accessory ConnectingAccessory Screen size Calculation methods Security lock IndexS0807-0A
Related manuals
Manual 54 pages 35.04 Kb