Panasonic PT-AX200E manual Important Safety Notice, Important the Moulded Plug U.K. only

Page 3

Important Safety Notice

IMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark a or the BSI mark ` on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorised Service Centre.

If the fitted moulded plug is unsuitable for the mains socket in your home, then the fuse should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

Important Information

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

WARNING: THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Green - and - Yellow: Earth

Blue:Neutral

Brown:Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol W or coloured GREEN or GREEN - AND - YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

BS1363/A	N
	N
13A250V	-8
	-8
	HE
L
ASA

http://www.pureglare.com.au

ENGLISH - 3

Image 3

Contents Operating Instructions To rain or moisture Important Safety NoticeFor business users in the European Union This Apparatus Must be EarthedImportant the Moulded Plug U.K. only Important Safety NoticeContents Position menu ContentsMenu Navigation Picture menuPrecautions with regard to safety Use only the specified batteries Precautions with regard to safetyDo not set up the projector outdoors Do not look into the lens while the projector is being usedElectric shocks can result if this is not done Remove the used batteries from the remote control promptlyDo not put your weight on this projector Do not mix old and new batteriesScreen Order to get the best picture qualityDo not touch the surfaces of the lens with your bare hands Liquid crystal panelMains lead for UK AccessoriesAbout Your Projector Remote controlProjector body About Your ProjectorTop and front view About Your Projector Back and bottom view Projected image Setting upCalculation methods for screen dimensions Screen size and throw distanceMounting in the ceiling and projecting from front Front leg adjusters and throwing angleSetting up Projection methodVertical shift Adjusting the lens shift leverLens shift and positioning Horizontal shift63% 25% Setting up Projector location rangeWhen the screen position is fixed When the projector position is fixedConnections Before connecting to the projectorConnecting to Component IN/VIDEO IN/S-VIDEO Connecting to Computer IN/HDMIMains lead Switching the projector on/offPower indicator ConnectingSwitching on the projector Switching off the projectorSwitching the projector on/off Projecting an image Selecting the input signalSwitch on the connected devices Adjust the focus and the projected image sizeTurning on the button backlight Remote control operationSwitching the preset settings Operating rangeRemote control operation Adjusting the imageSwitching the aspect ratio Resetting to the factory default settingsBrightness Setting your own colour profileAdjusting the selected colour Managing stored logsDeleting the saved profiles Saving a log setting as a profileChanging the profile names Loading saved profilesSwitching the input signal Assigning the functions for shortcutComponent Video Computer Hdmi 1 Hdmi 2 Menu Navigation Navigating through the MenuDisplaying the main menu Default Main menu and sub-menuMenu Navigation Aspect Clock Phase *2Position DOT Clock *1Picture menu Advanced Menu Colour TemperatureDynamic Iris Light HarmonizerFavourite Load Favourite SaveYou can edit the named memory settings Signal ModeDeleting a memory setting Changing the name of the memory settingDOT Clock Clock PhasePosition menu PositionScroll Component signalsComputer signals Position menu Aspect ratio options and projection exampleKeystone Auto SetupWSS Over ScanRemote control Function ButtonBlank function Option menu Test Pattern Lamp PowerSleep Lamp RuntimeTemp indicator Temp and Lamp IndicatorsManaging the indicated problems Lamp indicatorCleaning the projector Care and ReplacementBefore replacing the lamp unit Care and ReplacementWhen to replace the lamp unit Replacing the lamp unitCare and Replacement Removing and replacing the lamp unit Resetting the Lamp RuntimeSelect Lamp Runtime Troubleshooting Technical Information List of compatible signalsSerial terminal Technical Information Communication settings Control commandsInquiry Commands Specifications Hdmi VideoComputer ComponentInstalling the safety cable Ceiling mount bracket safeguardsDimensions Trademark acknowledgementsUnit mm Index Main menu Navigation Sub-menu Accessory ConnectingAccessory Screen size Calculation methods Security lock Index

Related manuals

Manual 54 pages 37.83 Kb