Panasonic PT-AX200E manual Wss, Over Scan, Keystone, Auto Setup, Position menu

Page 36

POSITION menu

WSS

WSS (Wide Screen Signalling) detects if a PAL/

625p (576p)/625i (576i) signal is input and that signal has an identification signal, and switch the aspect ratio to required setting automatically. You can switch the system off manually.

OVER SCAN

If the 4 edges of an image is partly dropped, you can use this function to adjust and project it properly.

Setting range: 0 to +10

OVER SCAN is not available with COMPUTER signals.

KEYSTONE

If the projector is aligned non-perpendicularly to the screen, or if the projection screen has an angled surface, you can vertically correct keystone.

Image	Operation

Shrink

Enlarge

Setting range: -32 to 32

NOTE:

• You can correct the distortion ± 30 degrees from the vertical plane. For a better quality image, installing the projector with a minimum of distortion is recommended.

• Some distortion may be retained for the lens shift adjustment.

• The distortion of the main menu screen is not correctable.

• The result of the keystone correction will affect the aspect ratio and the size of the image.

AUTO SETUP

You can adjust V - POSITION, H - POSITION, DOT CLOCK and CLOCK PHASE automatically when connecting via COMPUTER IN. Press ENTER to adjust these at the same time.

Settings

36 - ENGLISH

http://www.pureglare.com.au

Image 36

Contents Operating Instructions Important Safety Notice For business users in the European UnionThis Apparatus Must be Earthed To rain or moistureImportant Safety Notice Important the Moulded Plug U.K. onlyContents Contents Menu NavigationPicture menu Position menuPrecautions with regard to safety Precautions with regard to safety Do not set up the projector outdoorsDo not look into the lens while the projector is being used Use only the specified batteriesRemove the used batteries from the remote control promptly Do not put your weight on this projectorDo not mix old and new batteries Electric shocks can result if this is not doneOrder to get the best picture quality Do not touch the surfaces of the lens with your bare handsLiquid crystal panel ScreenAccessories Mains lead for UKRemote control About Your ProjectorProjector body About Your ProjectorTop and front view About Your Projector Back and bottom view Setting up Calculation methods for screen dimensionsScreen size and throw distance Projected imageFront leg adjusters and throwing angle Setting upProjection method Mounting in the ceiling and projecting from frontAdjusting the lens shift lever Lens shift and positioningHorizontal shift Vertical shiftSetting up Projector location range When the screen position is fixedWhen the projector position is fixed 63% 25%Before connecting to the projector Connecting to Component IN/VIDEO IN/S-VIDEOConnecting to Computer IN/HDMI ConnectionsSwitching the projector on/off Power indicatorConnecting Mains leadSwitching on the projector Switching off the projectorSwitching the projector on/off Selecting the input signal Switch on the connected devicesAdjust the focus and the projected image size Projecting an imageRemote control operation Switching the preset settingsOperating range Turning on the button backlightAdjusting the image Switching the aspect ratioResetting to the factory default settings Remote control operationSetting your own colour profile Adjusting the selected colourManaging stored logs BrightnessSaving a log setting as a profile Changing the profile namesLoading saved profiles Deleting the saved profilesSwitching the input signal Assigning the functions for shortcutComponent Video Computer Hdmi 1 Hdmi 2 Menu Navigation Navigating through the MenuDisplaying the main menu Default Main menu and sub-menuMenu Navigation Clock Phase *2 PositionDOT Clock *1 AspectPicture menu Colour Temperature Dynamic IrisLight Harmonizer Advanced MenuFavourite Save Favourite LoadSignal Mode Deleting a memory settingChanging the name of the memory setting You can edit the named memory settingsClock Phase Position menuPosition DOT ClockComponent signals Computer signalsPosition menu Aspect ratio options and projection example ScrollAuto Setup WSSOver Scan KeystoneRemote control Function ButtonBlank function Option menu Lamp Power SleepLamp Runtime Test PatternTemp and Lamp Indicators Managing the indicated problemsLamp indicator Temp indicatorCare and Replacement Cleaning the projectorCare and Replacement When to replace the lamp unitReplacing the lamp unit Before replacing the lamp unitCare and Replacement Removing and replacing the lamp unit Resetting the Lamp RuntimeSelect Lamp Runtime Troubleshooting List of compatible signals Technical InformationSerial terminal Technical Information Communication settings Control commandsInquiry Commands Specifications Video ComputerComponent HdmiCeiling mount bracket safeguards Installing the safety cableDimensions Trademark acknowledgementsUnit mm Index Accessory Connecting Accessory Screen size Calculation methods Security lockIndex Main menu Navigation Sub-menu

Related manuals

Manual 54 pages 37.83 Kb