Panasonic PT-AX100E manual Important Safety Notice, Important the Moulded Plug U.K. only

Page 3

Important Safety Notice

IMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark a or the BSI mark ` on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorised Service Centre.

If the fitted moulded plug is unsuitable for the mains socket in your home, then the fuse should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

WARNING: THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Green - and - Yellow: Earth

Blue:Neutral

Brown:Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol W or coloured GREEN or GREEN - AND - YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

BS1363/A	N
	N
13A250V	-8
	-8
	HE
L
ASA

ENGLISH - 3

Image 3

Contents Operating Instructions Expose this appliance to rain or moisture Important Safety NoticeImportant the Moulded Plug U.K. only Important Safety NoticeContents Settings MaintenanceAppendix Precautions with regard to safety Do not look into the lens while the projector is being used Precautions with regard to safetyDo not place any heavy objects on top of the projector Do not put your weight on this projectorDo not cover the air inlet port or the air outlet port Always disconnect all cables before moving the projectorBefore use AccessoriesBefore use Remote control About Your ProjectorFront, back and top view Control panel ProjectorAbout Your Projector Top and front viewTerminals Back and bottom viewSetting up Calculation methods for screen dimensionsScreen size and throw distance Front leg adjuster and throwing angle Setting upProjection method Vertical shift Adjusting the Shift leverLens shift and positioning Horizontal shiftAdjustable projection range Projector location rangeAfter fixing the screen position Before connection to the projector Connecting with AV devicesConnecting with HDMI/PC ConnectionsMains lead Switching the projector on/offPower indicator ConnectingDisconnectingPower indicator Switching on the projectorSwitching off the projector Switching the projector on/offFocus ring Zoom ring Selecting the input signalProjecting an image Positioning the imageCapturing an image Remote control operationInput switching Operating rangeSwitching the picture mode Switching the aspect ratioSwitching off the projector automatically Resetting to the factory default settingsAdjusting the image Setting your own colour profileCreate a new profile Saving a log setting as a profile Loading saved profilesManaging stored logs Main menu Menu NavigationNavigating through MenuMenu Navigation Sub-menuBrightness Picture ModePicture Menu ContrastDynamic Iris Colour TemperatureTint SharpnessNR Noise Reduction Signal ModeFavourite Save Favourite LoadDOT Clock Clock PhasePosition Menu PositionAspect ratio options and projection example Component signalsAspect Position MenuOver Scan Auto SetupAspect ratio depend on signals WSSOption Menu Altitude InstallationLamp Power SleepControlling alerts Temp and Lamp IndicatorsLamp indicator Temp indicator Lamp indicatorCare and Replacement Before cleaningCleaning your projector When to replace the Lamp unit Care and ReplacementBefore replacing the Lamp unit Resetting the Lamp Runtime Replacing the lamp unitReplacing Troubleshooting Technical Information List of compatible signalsTechnical Information Pin assignments and signal namesCommunication settings Serial terminalBasic format Control commandsInquiry commands Cable specificationsProjector Option Menu 34 H Menu structurePicture Menu 28 H Position Menu 31 HNTSC/NTSC 4.43/PAL/PAL-M/PAL-N/SECAM SpecificationsSerial SpecificationsDimensions For business users in the European Union Trademark acknowledgementsAltitude IndexOSD Design OSD Position Over Scan Index