Panasonic PT-AX100E manual Precautions with regard to safety

Page 6

Preparation

Precautions with regard to safety

WARNINGS

If you notice smoke, strange smells or noise coming from the projector, disconnect the mains plug from the mains socket.

Do not continue to use the projector in such cases, otherwise fire or electric shocks could result. Check that no more smoke is coming out, and then contact an Authorised Service Centre for repairs. Do not attempt to repair the projector yourself, as this can be dangerous.

Do not install this projector in a place which is not strong enough to take the full weight of the projector.

If the installation location is not strong enough, it may fall down or tip over, and severe injury or damage could result.

Installation work (such as ceiling suspension) should only be carried out by a qualified technician.

If installation is not carried out correctly, there is the danger that injury or electric shocks may occur.

Do not use other than an authorised ceiling mount bracket.

If foreign objects or water get inside the projector, or if the projector is dropped or the cabinet is broken, disconnect the mains plug from the mains socket.

Continued use of the projector in this condition may result in fire or electric shocks.

Contact an Authorised Service Centre for repairs.

Do not overload the mains socket.

If the power supply is overloaded (for example, by using too many adapters), overheating may occur and fire may result.

Do not remove the cover or modify it in any way.

High voltages can cause fire or electric shocks. For any inspection, adjustment and repair work, please contact an Authorised Service Centre.

Clean the mains plug regularly to prevent it from becoming covered in dust.

If dust builds up on the mains plug, the resulting humidity can damage the insulation, which could result in fire. Pull the mains plug out from the mains socket and wipe it with a dry cloth.

If not using the projector for an extended period of time, pull the mains plug out from the mains socket.

Do not do anything that might damage the mains lead or the mains plug.

Do not damage the mains lead, make any modifications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

If the mains lead is used while damaged, electric shocks, short-circuits or fire may result.

Ask an Authorised Service Centre to carry out any repairs to the mains lead that might be necessary.

Do not handle the mains plug with wet hands.

Failure to observe this may result in electric shocks.

Insert the mains plug securely into the mains socket.

If the plug is not inserted correctly, electric shocks or overheating could result.

Do not use plugs which are damaged or mains sockets which are coming loose from the wall.

Do not place the projector on top of surfaces which are unstable.

If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or damage could result.

Do not place the projector into water or let it become wet.

Failure to observe this may result in fire or electric shocks.

Do not place the projector on soft materials such as carpets or sponge mats.

Doing so may cause the projector to overheat, which can cause burns, fire or damage to the projector.

Do not place liquid containers on top of the projector.

If water spills onto the projector or gets inside it, fire or electric shocks could result.

If any water gets inside the projector, contact an Authorised Service Centre.

Do not insert any foreign objects into the projector. Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing so can result in fire or electric shocks.

Do not allow the + and - terminals of the batteries to come into contact with metallic objects such as necklaces or hairpins.

Failure to observe this may cause the batteries to leak, overheat, explode or catch fire.

Store the batteries in a plastic bag and keep them away from metallic objects.

6 - ENGLISH

Image 6
Contents Operating Instructions Important Safety Notice Expose this appliance to rain or moistureImportant Safety Notice Important the Moulded Plug U.K. onlyContents Settings MaintenanceAppendix Precautions with regard to safety Precautions with regard to safety Do not look into the lens while the projector is being usedAlways disconnect all cables before moving the projector Do not put your weight on this projectorDo not cover the air inlet port or the air outlet port Do not place any heavy objects on top of the projectorAccessories Before useBefore use Remote control About Your ProjectorFront, back and top view Top and front view ProjectorAbout Your Projector Control panelBack and bottom view TerminalsSetting up Calculation methods for screen dimensionsScreen size and throw distance Front leg adjuster and throwing angle Setting upProjection method Horizontal shift Adjusting the Shift leverLens shift and positioning Vertical shiftAdjustable projection range Projector location rangeAfter fixing the screen position Connections Connecting with AV devicesConnecting with HDMI/PC Before connection to the projectorConnectingDisconnecting Switching the projector on/offPower indicator Mains leadSwitching the projector on/off Switching on the projectorSwitching off the projector Power indicatorPositioning the image Selecting the input signalProjecting an image Focus ring Zoom ringOperating range Remote control operationInput switching Capturing an imageResetting to the factory default settings Switching the aspect ratioSwitching off the projector automatically Switching the picture modeAdjusting the image Setting your own colour profileCreate a new profile Saving a log setting as a profile Loading saved profilesManaging stored logs Menu Menu NavigationNavigating through Main menuSub-menu Menu NavigationContrast Picture ModePicture Menu BrightnessSharpness Colour TemperatureTint Dynamic IrisFavourite Load Signal ModeFavourite Save NR Noise ReductionPosition Clock PhasePosition Menu DOT ClockPosition Menu Component signalsAspect Aspect ratio options and projection exampleWSS Auto SetupAspect ratio depend on signals Over ScanOption Menu Sleep InstallationLamp Power AltitudeLamp indicator Temp and Lamp IndicatorsLamp indicator Temp indicator Controlling alertsCare and Replacement Before cleaningCleaning your projector When to replace the Lamp unit Care and ReplacementBefore replacing the Lamp unit Resetting the Lamp Runtime Replacing the lamp unitReplacing Troubleshooting List of compatible signals Technical InformationSerial terminal Pin assignments and signal namesCommunication settings Technical InformationControl commands Basic formatInquiry commands Cable specificationsProjector Position Menu 31 H Menu structurePicture Menu 28 H Option Menu 34 HSpecifications NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/SECAMSpecifications SerialDimensions Trademark acknowledgements For business users in the European UnionIndex AltitudeIndex OSD Design OSD Position Over Scan