Panasonic PT-AX100E manual Installation, Sleep, Altitude, Lamp Power, Lamp Runtime, Test Pattern

Page 35

INSTALLATION

When installing the projector, select the projection method according to the projector position. Press I H to cycle through the options. See “Projection method” on page 15.

FRONT/DESK

Setting on a desk/floor and

projecting from front

 

FRONT/CEILING

Mounting in the ceiling and

projecting from front

 

REAR/DESK

Setting on a desk/floor and

projecting from rear

 

REAR/CEILING

Mounting in the ceiling and

projecting from rear

 

 

 

SLEEP

You can select the required duration of time and set the off timer to turn off the POWER of the projector automatically. 3 minutes before turn-off, the countdown of minutes will be displayed in the lower right corner. Press I H to cycle through the options. See “Switching off the projector automatically” on page 23.

ALTITUDE

If you use the projector at high elevations, set the fan speed to HIGH. Press I H to select HIGH or LOW.

NOTE:

At 1 400 m (4593 ft) above sea level, the setting must be HIGH.

LAMP POWER

You can adjust the power of the lamp to save on electricity, prolong the lamp life and reduce the noise.

Options

Function

 

 

NORMAL

When higher luminance is

required such as movies

 

 

 

ECO - MODE

When lower luminance is

sufficient such as in a small room

 

NOTE:

When no input signal is detected, the function is disabled.

OPTION Menu

LAMP RUNTIME

You can check how long time has been the lamp used.

NOTE:

LAMP RUNTIME is a relevant matter for lamp replacement timing. See “Care and Replacement” on page 37.

TEST PATTERN

You can use the 2 different of test pattern to adjust the focus of the image. The PICTURE MODE is switched to DYNAMIC temporarily, and return to the last used setting when return to projection.

1.Press ENTER to display test pattern 1 and adjust the focus with the Focus ring.

2.Press ENTER to display test pattern 2 and adjust the focus with the Focus ring again.

3.Press MENU or RETURN to return to the previous menu, or press repeatedly to return to the screen.

NOTE:

While a test pattern is displayed, the PICTURE MODE is changed temporarily to DYNAMIC. When the projector and/or the screen is tilted, adjust the focus at the centre of the image. The upper and lower edge might be out of focus. When the image is distorted in keystone, adjust the KEYSTONE in POSITION menu.

Settings

ENGLISH - 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Operating Instructions Expose this appliance to rain or moisture Important Safety NoticeImportant the Moulded Plug U.K. only Important Safety NoticeContents Appendix SettingsMaintenance Precautions with regard to safety Do not look into the lens while the projector is being used Precautions with regard to safetyDo not place any heavy objects on top of the projector Do not put your weight on this projectorDo not cover the air inlet port or the air outlet port Always disconnect all cables before moving the projectorBefore use AccessoriesBefore use Front, back and top view Remote controlAbout Your Projector Control panel ProjectorAbout Your Projector Top and front viewTerminals Back and bottom viewScreen size and throw distance Setting upCalculation methods for screen dimensions Projection method Front leg adjuster and throwing angleSetting up Vertical shift Adjusting the Shift leverLens shift and positioning Horizontal shiftAfter fixing the screen position Adjustable projection rangeProjector location range Before connection to the projector Connecting with AV devicesConnecting with HDMI/PC ConnectionsMains lead Switching the projector on/offPower indicator ConnectingDisconnectingPower indicator Switching on the projectorSwitching off the projector Switching the projector on/offFocus ring Zoom ring Selecting the input signalProjecting an image Positioning the imageCapturing an image Remote control operationInput switching Operating rangeSwitching the picture mode Switching the aspect ratioSwitching off the projector automatically Resetting to the factory default settingsCreate a new profile Adjusting the imageSetting your own colour profile Managing stored logs Saving a log setting as a profileLoading saved profiles Main menu Menu NavigationNavigating through MenuMenu Navigation Sub-menuBrightness Picture ModePicture Menu ContrastDynamic Iris Colour TemperatureTint SharpnessNR Noise Reduction Signal ModeFavourite Save Favourite LoadDOT Clock Clock PhasePosition Menu PositionAspect ratio options and projection example Component signalsAspect Position MenuOver Scan Auto SetupAspect ratio depend on signals WSSOption Menu Altitude InstallationLamp Power SleepControlling alerts Temp and Lamp IndicatorsLamp indicator Temp indicator Lamp indicatorCleaning your projector Care and ReplacementBefore cleaning Before replacing the Lamp unit When to replace the Lamp unitCare and Replacement Replacing Resetting the Lamp RuntimeReplacing the lamp unit Troubleshooting Technical Information List of compatible signalsTechnical Information Pin assignments and signal namesCommunication settings Serial terminalBasic format Control commandsProjector Inquiry commandsCable specifications Option Menu 34 H Menu structurePicture Menu 28 H Position Menu 31 HNTSC/NTSC 4.43/PAL/PAL-M/PAL-N/SECAM SpecificationsSerial SpecificationsDimensions For business users in the European Union Trademark acknowledgementsAltitude IndexOSD Design OSD Position Over Scan Index
Top Page Image Contents