Panasonic PT-AX100E manual Replacing the lamp unit, Resetting the Lamp Runtime

Page 39

Care and Replacement

Replacing the lamp unit

Replacing

1.Turn off the MAIN POWER switch according to the procedure “Switching the projector on/off” on page 19, and then disconnect the mains plug from the mains socket and check that the area around the lamp unit has cooled down.

2.Use a Phillips screwdriver to turn the lamp unit cover fixing screws at the bottom of the projector, and then remove the lamp unit cover.

3.Use a Phillips screw driver to loosen the two lamp unit fixing screws until the screws turn freely. Then hold the handle of the lamp unit and gently pull it out from the projector.

4.Insert the new lamp unit while making sure that the direction of insertion is correct, and then use a Phillips screwdriver to securely tighten the lamp unit fixing screw.

5.Install the lamp unit cover, and then use a Phillips screwdriver to securely tighten the lamp unit cover fixing screws.

Lamp unit cover fixing screws

Lamp unit cover Lamp unit fixing screws

Press

Press

here

here

 

Handle

NOTE:

Be sure to install the lamp unit and the lamp unit cover securely. If they are not securely installed, it may cause the protection circuit to operate so that the power cannot be turned on.

Grip the handle when you remove the lamp unit. Some parts of the lamp unit are sharpened and may cause injury.

Resetting the LAMP RUNTIME

If the lamp usage time has passed 2 000 hours (when LAMP POWER has been set to NORMAL), the projector will switch to standby mode after approximately 10 minutes of operation. The resetting procedure should thus be completed within 10 minutes.

1.Insert the mains plug into the mains socket and then press the MAIN POWER switch.

2.Press the POWER button so that a picture is projected onto the screen.

3.Press the MENU button to display the menu screen, and then press the F or G button to select the OPTION menu.

4.Press the ENTER button, and then press the F or G button to select LAMP RUNTIME.

5.Press and hold the ENTER button for approximately

3 seconds. The confirmation screen, “LAMP RUNTIME RESET.” is displayed and select OK.

6.Turn off the power.

This will reset the cumulative usage time for the lamp unit to zero.

 

 

 

 

 

 

INPUT GUIDE

DETAILED

 

 

 

 

 

 

 

 

 

 

 

 

 

OSD DESIGN

TYPE1

 

 

 

 

 

 

 

 

OSD POSITION

 

 

 

 

CENTRE

 

 

 

 

 

 

 

 

BACK COLOUR

 

 

 

 

BLUE

 

 

 

 

 

 

 

 

STARTUP LOGO

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO SEARCH

ON

 

 

 

 

 

 

 

 

HDMI SIGNAL LEVEL

 

 

 

 

NORMAL

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTALLATION

FRONT/DESK

 

 

 

 

 

 

 

 

SLEEP

 

 

 

 

OFF

 

 

 

 

 

 

 

 

ALTITUDE

 

 

 

 

LOW

 

 

 

 

 

 

 

 

LAMP POWER

 

 

 

 

NORMAL

 

 

 

 

 

 

 

 

LAMP RUNTIME

1820H

 

 

TEST PATTERN

 

 

 

 

 

 

 

 

Maintenance

ENGLISH - 39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Operating Instructions Expose this appliance to rain or moisture Important Safety NoticeImportant the Moulded Plug U.K. only Important Safety NoticeContents Settings MaintenanceAppendix Precautions with regard to safety Do not look into the lens while the projector is being used Precautions with regard to safetyDo not place any heavy objects on top of the projector Do not put your weight on this projectorDo not cover the air inlet port or the air outlet port Always disconnect all cables before moving the projectorBefore use AccessoriesBefore use Remote control About Your ProjectorFront, back and top view Control panel ProjectorAbout Your Projector Top and front viewTerminals Back and bottom viewSetting up Calculation methods for screen dimensionsScreen size and throw distance Front leg adjuster and throwing angle Setting upProjection method Vertical shift Adjusting the Shift leverLens shift and positioning Horizontal shiftAdjustable projection range Projector location rangeAfter fixing the screen position Before connection to the projector Connecting with AV devicesConnecting with HDMI/PC ConnectionsMains lead Switching the projector on/offPower indicator ConnectingDisconnectingPower indicator Switching on the projectorSwitching off the projector Switching the projector on/offFocus ring Zoom ring Selecting the input signalProjecting an image Positioning the imageCapturing an image Remote control operationInput switching Operating rangeSwitching the picture mode Switching the aspect ratioSwitching off the projector automatically Resetting to the factory default settingsAdjusting the image Setting your own colour profileCreate a new profile Saving a log setting as a profile Loading saved profilesManaging stored logs Main menu Menu NavigationNavigating through MenuMenu Navigation Sub-menuBrightness Picture ModePicture Menu ContrastDynamic Iris Colour TemperatureTint SharpnessNR Noise Reduction Signal ModeFavourite Save Favourite LoadDOT Clock Clock PhasePosition Menu PositionAspect ratio options and projection example Component signalsAspect Position MenuOver Scan Auto SetupAspect ratio depend on signals WSSOption Menu Altitude InstallationLamp Power SleepControlling alerts Temp and Lamp IndicatorsLamp indicator Temp indicator Lamp indicatorCare and Replacement Before cleaningCleaning your projector When to replace the Lamp unit Care and ReplacementBefore replacing the Lamp unit Resetting the Lamp Runtime Replacing the lamp unitReplacing Troubleshooting Technical Information List of compatible signalsTechnical Information Pin assignments and signal namesCommunication settings Serial terminalBasic format Control commandsInquiry commands Cable specificationsProjector Option Menu 34 H Menu structurePicture Menu 28 H Position Menu 31 HNTSC/NTSC 4.43/PAL/PAL-M/PAL-N/SECAM SpecificationsSerial SpecificationsDimensions For business users in the European Union Trademark acknowledgementsAltitude IndexOSD Design OSD Position Over Scan Index
Top Page Image Contents