Panasonic PT-D7500U manual Initial setting of network module, Menu screen will be displayed

Page 83

Initial setting of network module

Procedure of setting

MAIN MENU

PICTURE

POSITION

LANGUAGE

OPTION

TEST PATTERN

RESISTERED SIGNAL LIST

:MENU SELECT

ENTER:SUB MENU

OPTION

	SYSTEM INFORMATION
	VIDEO SETTING
	NETWORK SETTING
	FAN CONTROL	NORMAL
	P IN P	ON
	FUNC1	P IN P
	CONTRAST	NORMAL
	PASSWORD
	:MENU SELECT
ENTER:SUB MENU


NETWORK SETTING
	HOST NAME	PROJECTOR
	DHCP	OFF
	IP ADRESS	192.168.	0.	8
	PORT	80
	NET MASK	255.255.255.		0
	GATEWAY	192.168.	0.	1
	MAC ADRESS	00.00.00.00.00.00

STORE

:MENU SELECT

ENTER:ADJUST

Press the “MENU” button.

The MENU screen will be displayed.

Select “OPTION” with the buttons.

Press the “ENTER” button.

The OPTION screen will be displayed.

Select “NETWORK SETTING” with the buttons.

Press the “ENTER” button.

The NETWORK SETTING screen will be displayed.

Select items with the buttons and press the “ENTER” button to change the setting.

Select the “STORE” with the

buttons and press the “ENTER” button twice.

The on-line lamp of network module turns off and then turns on.

Note

•It takes about two minutes for the setting to be reflected in the system.

•Do not turn off the main power supply until the on- line lamp of network module turns on again.

83

Image 83

Contents Model No. PT-D7500U Commercial UseSerial number Dear Panasonic CustomerModel number PT-D7500U / PT-D7600U Page Contents Precautions with regard to safety Precautions with regard to safety Lamp section may break AccessoriesDo not look into the lens while the projector is being used Do not use the old lamp unitPrecautions on handling Examples of system expansion Name and function of parts Remote controlWhen the operation mode selector is set to Projector When the operation mode selector is set to Computer Name and function of parts Front and side of the projector Rear view of the main unit Controls on rear panel REMOTE2 terminal Video in terminalVideo OUT terminal RGB YPBPR2 input/RGB YPBPR1 output terminal pages 26Loading dry cells Using the remote control unitEffective range of remote control operation Procedure of ID setting Setting projector ID number to remote controlUsing the remote control unit Operation mode selector switch Using the remote control as a PC mouseUsing a wired remote control Projection scheme Installation geometry InstallationAdjusting the leveling feet Inch Projection distance SH Effective screen heightSize Effective For the screen aspect ratio Units m feet/inches InstallationScreen dimensions Projection distance L Zoom lens WidthSW Minimum Maximum ET-D75LE2/SC 2.0-3.0 ET-D75LE2SC ET-D75LE1ET-D75LE1SC ET-D75LE2・SYNC/Y SDA HD/SYNC SCL ConnectionBefore starting connection Video deck TBC built-in High-vision video deck Example of connecting with Video devicesVideo deck TBC built-in Color monitor Control PC Control PC PC or color monitor With RGB input terminals Example of connecting with personal computersConnection Color monitor with RGB input terminal Example of connecting with the signal selectorTypes of the input modules optional Installation of input module optionalInstalling the input module Insert the input module Procedure of installationRegister the input signal Remove the slot coverInstallation of input module optional Connecting signals to the input moduleSUB BNC Connecting the signal to the analog RGB signal input moduleConnecting the component signals RGB signal input module optionalVideo signal input module optional Connecting the signal to the video signal input moduleInstallation of input module optional Connecting the video signalsConnecting the component signals ET-MD95SD1 for 480i/576i Serial digital input module optionalET-MD95SD2 for 480p/480i/576i SD signal Business-use digital video deckAuto Installing the input module optionalET-MD95SD3 for HD SDI DVI-D input module optional Connecting signals to the DVI signal input modulePin No Signal Pull the projection lens How to install the projection lensHow to remove the projection lens Roughly adjust the focus of the lens. Refer to Powering up the projectorMaking adjustment and selection Press the l button. on the main unit or the remote controlProjection Powering off the projectorChoose an item and adjust it using Buttons How to adjust the lensAutomatic adjustment Auto Setup Press the Enter button Registration of input signal dataRegistration of new data Press the Menu buttonConfirm overwriting registration screen will be displayed Registration of input signal dataIf new registration is not available because of full memory Sub memory How to register into sub memoryHow to erase sub memory Change registered signals screen will appearDesignation can be set by the sub memory items On-screen indicationsRestrictions Using the digital zoom D.ZOOM + function Using the Freeze functionUsing the Shutter function Structure of menu screens On-screen menusReturning to the previous screen Menu items settingResetting to the factory default Basic operations on menu screenSelect Picture Mode with the buttons Adjusting the pictureSwitching the picture mode Switching the AI controlRepeat Steps To adjust BRIGHT, Color or Tint Adjusting Contrast / Bright / Color / TintAdjustment procedure to adjust picture color intensity Adjust the level with ButtonsUSER, STANDARD, NATURAL, CINEMA, Graphic Adjusting the color temperatureAdjusting the picture Operation Adjustment RemarksSelect Picture with the buttons Press Enter button Adjusting color matchingProcedure of adjustment Select the desired color for adjustment With the buttonsSelect Picture with the buttons Sharpness / Gamma / Noise reduction / Pulldown modeAdjustment items Operation Smpte Signal levelTo input Betacam with YCbCr To set the sRGB compliant pictureShift adjustment Adjusting the positionSize adjustment screen will be displayed Size adjustmentSize modes Adjusting the positionSelect Blanking with the buttons Press the Enter button Blanking adjustmentClock phase adjustment Total DOTS, Displayed DOTS, Total Lines and Displayed Lines Adjusting the input resolutionInput Resolution screen will be displayed Value changes from 1 to Adjusting the clamp positionSelect Position with the buttons Press the Enter button Clamp Position screen will be displayedSelect Keystone with the buttons Press the Enter button Adjust the Keystone horizontally With the buttonsAdjust the vertical Linearity with Buttons Keystone distortion correctionAdjustment marker Edge blending adjustmentSpecify the area to be adjusted with the buttons To display the adjustment markerSelect the Language with the buttons Press the Enter button Changing the display languageSelect the Bright with the buttons Press the Enter button How to change the system format Option screen will be displayed Procedure of settingVideo Setting screen will be displayed Select Option with the buttons Press the Enter buttonHow to use RGB Reality mode ID number need not be set when only one projector is used Option settingsID number setting FRONT-F FRONT-C REAR-C REAR-F Installation SettingOptional settings RGB2 select Lamp powerLamp select Lamp cooling timeSystem information Video settingAutomatic adjustment Option settingsType Main windowSubwindow Frame lockList of P in P Setting FUNC1Password ContrastNormal Maximum Brightness Maximum Normal Setting the contrast modeSelect Option with the buttons Press Enter button ModeHI-Z TTL These buttons toggle between 75 Ω and HI-Z TTLSYNC. Term Examples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPress and buttons to select Option Press the Enter button Procedure of setting communication conditionsUsing the serial terminals RS232C Setting screen will be displayedConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications External appearance Using the Remote 2 terminalPin assignments and control Sub 9-pin femaleCycle of displayed internal test patterns Displaying the internal test patternRS-422 control functions Name and function of network module parts How to use network module optionalExample of connection Menu screen will be displayed Initial setting of network moduleNetwork Setting screen will be displayed Port No How to use network module optionalItems Function Description Accessing from the Web browser Top Network settingNetwork setting Projector control Status indication Smtp Mail settingMail setting page continuing Page For control of image files Monitor Indication of monitor lampLamp Information Checkpoint Remedial measure IndicationDismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterIndication after 1 300 hours Replacement of lamp unitTiming of lamp unit replacement You might get burned if you touch it while it is still hot Procedure of lamp unit replacementReplacement of lamp unit Used hours of the specified lamp unit will be reset to zero Press the Enter button. When OK? is displayed, pressAn item Lamp Reset will be added No image appears on Symptoms CheckpointPower does not turn on Remote control doesPT-D7500U SpecificationsPT-D7500U PT-D7600U SpecificationsAppendix Compatible RGB/YPBPR Signals530 Units mminch Outside dimensionsTrademark Acknowledgement Concernant LA SÉ Curité Ne pas retirer le couvercle ou le modifier Pré cautions concernant la sé curitéNe pas couvrir le filtre et la sortie d’air Ne pas surcharger la prise de courantNe pas mettre d’objets é trangers dans le projecteur Ne pas placer le projecteur sur des surfaces instablesNe pas placer des ré cipients de liquide sur le projecteur Ne dé montez pas le bloc lampeCela peut entraîner une rupture de la lampe Pré cautions concernant la sé curité’utiliser que la pile indiqué e Nutilisez pas un bloc lampe usagéMise au rebut Nettoyage et maintenancePré cautions pour la manipulation Indication aprè s 1 300 heures Remplacement de la lampeProcé dure de remplacement de la lampe Remplacement de la lampe Remplacement de la lampe111 Panasonic Canada Inc Professional/Industrial VideoTechnical Support 800 FAX 201 Mail pbtssupport@panasonic.com