Panasonic PT-FW300NTE, PT-FW300E manual Read this first, Minimum required setting screen

Page 13

Read this first

Minimum required setting screen

When you start the projection for the first time, the minimum required setting screen for projection will be displayed.

 

INITIAL SETTING

INSTALLATION

 

1.

Select the required language setting by pressing

Select the required installation method.

 

I H, then press the ENTER button.

 

Setting on a desk/floor and

 

INITIAL SETTING

FRONT/DESK

 

projecting from front

 

 

 

 

 

FRONT/CEILING

Mounting on the ceiling and

 

 

projecting from front

 

 

 

 

 

REAR/DESK

Setting on a desk/floor and

 

 

projecting from rear

 

 

 

 

 

REAR/CEILING

Mounting on the ceiling and

 

ENGLISH

projecting from rear

 

 

 

 

SCREEN FORMAT

 

PLEASE SELECT LANGUAGE

Select the required screen format by pressing I H.

 

SELECT

16:10

When project on a 16:10 or 4:3

 

ENTER

 

screen.

 

16:9

When project on a 16:9 screen.

 

 

Preparation

2.Select the minimum required settings to start the projection.

Press the RETURN button to return to the language setting menu.

Press F G to move through the menu items. Press I H to select the required setting.

Press the ENTER button to complete the setting and start the projection.

INITIAL SETTING

INSTALLATION

FRONT/DESK

 

 

 

 

SCREEN FORMAT

16:10

 

 

 

 

 

 

 

SCREEN POSITION

CENTER

 

 

 

 

 

 

 

HIGH ALTITUDE MODE

OFF

 

 

 

 

SWITCH TO HIGH ALTITUDE MODE "ON" IF OVER 1400m(4593Ft).

RETURN

SELECT

ENTER

SCREEN POSITION

When SCREEN FORMAT menu is set to 16:9, you can select the menu display position by pressing I H.

LOW

Displays the menu in the lower part

 

of the screen.

CENTER

Displays the menu in the middle of

 

the screen.

HIGH

Displays the menu in the upper part

 

of the screen.

HIGH ALTITUDE MODE

If you use the projector at high elevation, the HIGH ALTITUDE MODE setting need to be ON to set the fan speed high.

OFF

The fan speed is low.

ON

The fan speed is high.

NOTE:

•At 1 400 - 2700 m (4 593 - 8 858 ft) above sea level, the setting must be ON.

•The loudness of fan noise depends on the HIGH ALTITUDE MODE setting.

NOTE:

Once you finish the minimum requirement setting, it will not be displayed again unless the projector is initialised. See “INITIALIZE ALL” on page 45.

You can change the each setting from the main menu. See “Menu Navigation” on page 32.

ENGLISH - 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PT-FW300E This Apparatus Must be Earthed Important Safety NoticeTo rain or moisture For business users in the European Union Important Safety NoticeDeclaration of Conformity DoC Declaration of ConformityEnglish Contents Maintenance SettingsContents AppendixPrecautions with regard to safety Do not set up the projector outdoors Precautions with regard to safetyDo not look into the lens while the projector is being used Do not put your weight on this projector Remove the used batteries from the remote control promptlyUse only the specified batteries Do not mix old and new batteriesOrder to get the best picture quality SecurityLiquid crystal panel Optical componentsPower cord secure lock AccessoriesMains lead Read this first Minimum required setting screenProjector body About Your ProjectorTop and front view Control panelAbout Your Projector Back and bottom view Auto cleaning filter ACF Front leg Adjusters CompartmentSecurity lock Lamp unit compartment Air exhaust portAttaching a hand strap Top view Remote control indicator Remote controlCLOCK, Clock Phase and Signal Search for Battery compartmentScreen size and throw distance Setting upCalculation methods Projection size 16 Throw distance LSetting up Front leg adjusters and throwing angleProjection method Mounting on the ceiling and projecting from frontLens shift and positioning Adjusting the lens shift leverHorizontal shift Vertical shiftWhen the screen position is fixed Setting up Projector location rangeWhen the projector position is fixed Connections Connecting example ComputersBefore connection to the projector LAN terminalConnecting with Video IN/S-VIDEO Connecting example AV equipmentConnecting with DVI-D ConnectionsConnecting Switching the projector on/offDirect power on function Direct power off functionSwitching the projector on/off Power indicatorPower indicator informs you the status of the power Switching off the projector Switching on the projectorSwitch the Main Power on Press the power button Switch off the Main Power on the back of the projectorProjecting an image Selecting the input signalPositioning the image Setting up the image position automatically Remote control operationOperating range Facing to the projectorEnlarging the centred area Switching the input signalProjecting an image in INDEX-WINDOW mode Resetting to the factory default settingsCapturing an image Stopping the projectionSwitching the signal Using an assigned functionSide by Side function signal combination table Projecting 2 different source image at a timeControlling the volume of the speaker Using the laser pointerDisable the Laser button Laser pointer beam emitterMain menu and Sub-menu Menu NavigationInput Guide OSD DesignMenu Navigation Filter Counter ResetOperating procedure Adjusting with the bar scale itemsNavigating through the menu Displaying the Main menuPicture menu Daylight View Color TemperatureDigital Cinema Reality TV-SYSTEMPosition menu Position menu AspectAspect ratio options 169Frame Lock Display Option menu Screen SettingDVI-D ON-SCREEN DisplaySignal Search Auto SetupWide Mode Sxga ModeOther Functions No Signal SHUT-OFF Projector Setup menuStatus COMPUTER2 SelectHigh Altitude Mode InstallationAudio Setting EmulateTest Pattern Filter Counter ResetInitialize ALL Remaining Filter of Status in ProjectorPassword Change PasswordSecurity menu Text DisplayControl Device Setup Menu Lock PasswordMenu Lock Security menuNetwork menu Wireless LAN PT-FW300NTEonlyItems in Network menu Network menu, the following items are availableManaging the indicated problems TEMP, Lamp and Filter IndicatorsLamp indicator Temp indicatorCleaning the projector Care and ReplacementReplacing the Lamp unit Care and Replacement Replacement procedure Replacing the Auto Cleaning Filter ACFWhen to replace the ACF Before replacing the ACFCounter Reset in Projector Setup Resetting the RemainingTurn the projector upside down and place it gently On a soft clothTroubleshooting Technical Information List of compatible signalsQuality*2 KHz MHzSerial terminal Control commands Technical Information Cable specificationsComputer connection guidance ProjectorSwitching input Signals Lamp switchingInput signal Remote terminalInstalling the safety cable Ceiling mount bracket safeguardsDVI-D in terminal Screen size and throw distance for 43 aspect ratio Screen size and throw distance for 169 aspect ratioSW m = SD x SH m = SD x LW m = 0.0339 x SD LT m = 0.0653 x SDSpecifications OUT VideoDVI-D AudioTrademark acknowledgements DimensionsUnit mm Digital Cinema Reality Digital Zoom IndexIndex Picture Mode
Top Page Image Contents