Panasonic PT-FW300E Installation, High Altitude Mode, Emulate, Function Button, Audio Setting

Page 44

PROJECTOR SETUP menu

INSTALLATION

When installing the projector, select the projection method according to the projector position. Press I H to cycle through the options. See “Projection method” on page 18.

FRONT/DESK

Setting on a desk/floor and

projecting from front

 

FRONT/CEILING

Mounting on the ceiling and

projecting from front

 

REAR/DESK

Setting on a desk/floor and

projecting from rear

 

REAR/CEILING

Mounting on the ceiling and

projecting from rear

 

HIGH ALTITUDE MODE

If you use the projector at high elevation, the HIGH ALTITUDE MODE setting needs to be ON to set the fan speed high. Press I H to select the required option.

OFF

The fan speed is low.

ON

The fan speed is high.

NOTE:

•At 1 400 m (4 593 ft) above sea level, the setting must be ON.

•The loudness of fan noise depends on the HIGH ALTITUDE MODE setting.

EMULATE

You can switch to the Panasonic past model's control commands for COMPUTER connection.

Settings

DEFAULT

F100, FW100, F200, F300,

FW300 models

 

 

 

 

D3500

D3500 models

 

D4000

D4000 models

 

D/W5K series

D5500, DW5000, D5600,

 

DW5100, D5700 models

 

 

 

L730

L520, L720 models

 

L780

L750, L780 models

 

L735

L735 models

 

L785

L785 models

 

LB/W80

LB75, LB80, LW80 models

 

 

 

FUNCTION BUTTON

You can assign a certain menu function to the FUNCTION button as shortcut. Press I H to select the required menu option, and the ENTER button.

Options

Functions

Refer

DISABLE

Deactivate the FUNCTION

-

button.

 

 

ASPECT

Display the ASPECT menu.

38

PICTURE MODE

Display the PICTURE MODE

35

menu.

 

 

DAYLIGHT VIEW

Display the DAYLIGHT VIEW

36

menu.

 

 

NOTE:

•Without any operation for 5 seconds, the displayed menu will be disappeared.

AUDIO SETTING

VOLUME

You can adjust the volume of the built-in monaural speaker and VARIABLE AUDIO OUT terminal.

IDecrease

H Increase

BALANCE

You can adjust to hear the sound played equally through both right and left from VARIABLE AUDIO OUT, or shift the balance so more sound plays through the left or right side.

IMore sound plays through the left side

HMore sound plays through the right side

IN STANDBY MODE

You can switch on/off the sound output in standby mode.

OFF

No sound in standby mode.

ON

Output audio in standby mode.

AUDIO IN SELECT

You can switch the audio output method for COMPUTER1 IN, COMPUTER2 IN and DVI-D IN terminals.

DVI

COM.AUDIO IN 2

Output audio that is input to the

COMPUTER AUDIO 2.

AUDIO IN Output audio that is input to the

AUDIO IN.

COMPUTER1

COM.AUDIO IN 1

Output audio that is input to the

COMPUTER AUDIO 1.

AUDIO IN Output audio that is input to the

AUDIO IN.

ENGLISH - 44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents PT-FW300E To rain or moisture Important Safety NoticeThis Apparatus Must be Earthed Important Safety Notice For business users in the European UnionDeclaration of Conformity Declaration of Conformity DoCEnglish Contents Settings MaintenanceContents AppendixPrecautions with regard to safety Do not look into the lens while the projector is being used Precautions with regard to safetyDo not set up the projector outdoors Remove the used batteries from the remote control promptly Do not put your weight on this projectorUse only the specified batteries Do not mix old and new batteriesSecurity Order to get the best picture qualityLiquid crystal panel Optical componentsMains lead AccessoriesPower cord secure lock Minimum required setting screen Read this firstAbout Your Projector Projector bodyTop and front view Control panelAuto cleaning filter ACF Front leg Adjusters Compartment About Your Projector Back and bottom viewSecurity lock Lamp unit compartment Air exhaust portRemote control Attaching a hand strap Top view Remote control indicatorCLOCK, Clock Phase and Signal Search for Battery compartmentSetting up Screen size and throw distanceCalculation methods Projection size 16 Throw distance LFront leg adjusters and throwing angle Setting upProjection method Mounting on the ceiling and projecting from frontAdjusting the lens shift lever Lens shift and positioningHorizontal shift Vertical shiftWhen the projector position is fixed Setting up Projector location rangeWhen the screen position is fixed Connecting example Computers ConnectionsBefore connection to the projector LAN terminalConnecting example AV equipment Connecting with Video IN/S-VIDEOConnecting with DVI-D ConnectionsSwitching the projector on/off ConnectingDirect power on function Direct power off functionPower indicator informs you the status of the power Power indicatorSwitching the projector on/off Switching on the projector Switching off the projectorSwitch the Main Power on Press the power button Switch off the Main Power on the back of the projectorPositioning the image Selecting the input signalProjecting an image Remote control operation Setting up the image position automaticallyOperating range Facing to the projectorSwitching the input signal Enlarging the centred areaResetting to the factory default settings Projecting an image in INDEX-WINDOW modeCapturing an image Stopping the projectionUsing an assigned function Switching the signalSide by Side function signal combination table Projecting 2 different source image at a timeUsing the laser pointer Controlling the volume of the speakerDisable the Laser button Laser pointer beam emitterMenu Navigation Main menu and Sub-menuInput Guide OSD DesignFilter Counter Reset Menu NavigationAdjusting with the bar scale items Operating procedureNavigating through the menu Displaying the Main menuPicture menu Color Temperature Daylight ViewDigital Cinema Reality TV-SYSTEMPosition menu Aspect Position menuAspect ratio options 169Frame Lock Screen Setting Display Option menuDVI-D ON-SCREEN DisplayAuto Setup Signal SearchWide Mode Sxga ModeOther Functions Projector Setup menu No Signal SHUT-OFFStatus COMPUTER2 SelectInstallation High Altitude ModeAudio Setting EmulateFilter Counter Reset Test PatternInitialize ALL Remaining Filter of Status in ProjectorPassword Password ChangeSecurity menu Text DisplayMenu Lock Password Control Device SetupMenu Lock Security menuWireless LAN PT-FW300NTEonly Network menuItems in Network menu Network menu, the following items are availableTEMP, Lamp and Filter Indicators Managing the indicated problemsLamp indicator Temp indicatorReplacing the Lamp unit Care and ReplacementCleaning the projector Replacing the Auto Cleaning Filter ACF Care and Replacement Replacement procedureWhen to replace the ACF Before replacing the ACFResetting the Remaining Counter Reset in Projector SetupTurn the projector upside down and place it gently On a soft clothTroubleshooting List of compatible signals Technical InformationQuality*2 KHz MHzSerial terminal Technical Information Cable specifications Control commandsComputer connection guidance ProjectorLamp switching Switching input SignalsInput signal Remote terminalDVI-D in terminal Ceiling mount bracket safeguardsInstalling the safety cable Screen size and throw distance for 169 aspect ratio Screen size and throw distance for 43 aspect ratioSW m = SD x SH m = SD x LW m = 0.0339 x SD LT m = 0.0653 x SDSpecifications Video OUTDVI-D AudioUnit mm DimensionsTrademark acknowledgements Index Digital Cinema Reality Digital ZoomPicture Mode Index
Top Page Image Contents