Panasonic PT-F200NTU manual Serial terminal

Page 45

Technical Information

Serial terminal

The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connecter.

Connection

D-sub 9 pin (male)

Serial terminal (female)

Computer

Pin assignments and signal names

	Pin No.	Signal name	Contents
	A		NC
	B	TXD	Transmitted data
	C	RXD	Received data
	D		NC
	E	GND	Earth
	F		NC
	G	RTS	Connected internally
	H	CTS	Connected internally
	H	CTS
	I		NC

Communication settings

Signal level	RS-232C	Character length	8 bits

Sync. method	Asynchronous	Stop bit	1 bit

Baud rate	9 600 bps	X parameter	None

Parity	None	S parameter	None

Basic format

The data streaming from the computer will

STX

Command

:

Parameter

ETX

start with STX, and proceed to Command,

Start

byte

Parameter and end with ETX. You can

1 byte

End

3 bytes

1 byte -

(02h)

(03h)

add the required parameter.

4 bytes

The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds before sending the command.

If sending multiple commands, check that a response has been received from the projector for one command before sending the next command.

When a command which does not require parameters to be sent, the colon (:) is not required.

If an incorrect command is sent from the personal computer, the ER401 command will be sent from the projector to the personal computer.

Appendix

ENGLISH - 45

Image 45

Contents PT-F200U Model number PT-F200NTU / PT-F200U Important Safety NoticeDeclaration of Conformity Important Safety NoticeModel Number PT-F200NTU / PT-F200U Trade Name PanasonicContents Settings MaintenanceAppendix Precautions with regard to safety Do not set up the projector outdoors Precautions with regard to safetyDo not look into the lens while the projector is being used Use only the specified batteriesDo not put your weight on this projector Remove the used batteries from the remote control promptlyDo not mix old and new batteries Electric shocks can result if this is not doneSecurity AccessoriesRead this first Minimum required setting screenAbout Your Projector Remote controlAbout Your Projector Projector bodyTop and front view Control panelAbout Your Projector Back and bottom view Computer. Selectable for inputOutput by menu operation Calculation methods for screen dimensions Setting upScreen size and throw distance Projected image ScreenSetting up Front leg adjusters and throwing angleProjection method Mounting in the ceiling and projecting from frontLens shift and positioning Adjusting the Lens shift leverHorizontal shift Vertical shiftSetting up Projector location range When the screen position is fixedWhen the projector position is fixed Connections Connecting example ComputersBefore connection to the projector LAN terminalConnecting with Video IN/S-VIDEO Connecting example AV equipmentsConnecting with Component ConnectionsSwitching the projector on/off Power cordPower indicator Switching off the projector Switching on the projectorSwitching the projector on/off Switch the Main Power on Press the Power buttonProjecting an image Selecting the input signalPositioning the image Focus lever Zoom leverSetting up the image position automatically Remote control operationOperating range Facing to the projectorUsing the laser pointer Switching the input signalProjecting an image in INDEX-WINDOW mode Resetting to the factory default settingsCapturing an image Stopping the projection temporaryEnlarging the centered area Controlling the volume of the speakerEnlarging the image Shifting the center pointMenu Navigation Adjusting with the bar scale itemsNavigating through the Menu Displaying the Main menuMenu Navigation Main menu and Sub-menuAudio Balance Live Mode CUT Status InitializeNetwork Standby WEB ControlPicture menu Detailed Setup For S-VIDEO/VIDEO signalsFor RGB signals Position menu Resizing When the Resizing is set to OFFFrame Lock Position menuOption menu Direct Power on Power OFF TimerAuto Setup Signal SearchSetting Closed CaptionTest Pattern Password Change Input PasswordSecurity menu Text DisplayNetwork menu Items in Network menuNetwork menu, the following items are available Managing the indicated problems LAMP, Temp and ARF IndicatorsLamp indicator Temp indicatorCare and Replacement Cleaning the projectorReplacing the ARF Auto Rolling Filter When to replace the Lamp unit Care and Replacement Resetting the FilterReplacing the Lamp unit Before replacing the Lamp unitCare and Replacement Replacement procedure Ceiling mount bracket safeguardsInstalling the safety cable Removing and replacing the lamp unitTroubleshooting Technical Information List of compatible signalsQuality*2 Dots*1 KHz MHzSerial terminal Control commands Technical Information Cable specificationsComputer connection guidance ProjectorLamp switching Switching input SignalsRemote terminal Specifications OUT COMPUTER1Audio Computer AudioScreen size and throw distance for 169 aspect ratio Projection size 16 Throw distance LScreen height SH Screen width SW Minimum distance Trademark acknowledgements DimensionsUnit mm These Operating Instructions are printed on recycled paperALS Ambient Luminance Sensor IndexARF Auto Rolling Filter Calculation methodsNavigation buttons IndexScreen size Technical InformationAvis important concernant la sécurité Numéro de modèle PT-F200NTU / PT-F200UNuméro de série Avis important concernant la sécurité AvertissementDéclaration de conformité Avertissements Précautions de sécuritéPrécautions de sécurité Mises EN GardeUtiliser uniquement les piles spécifiées Ne pas mélanger des piles usées et des piles neuvesSinon cela peut causer des chocs électriques Précautions lors de linstallation Précautions lors du transportPrécautions lors de lutilisation Délai de remplacement de lUnité de la lampe Remplacement de lunité de la lampe«LAMPE DE REMPLACEMENT» est Avant de remplacer le lUnité de la lampeProtections du support de montage au plafond Installation du câble de sécuritéRetirer et remplacer la lampe De lUnité de La lampeTechnical Support Panasonic Projector Systems Company