Panasonic PT-F200NTU manual Remote terminal, Lamp switching, Switching input Signals

Page 47

Technical Information

REMOTE terminal

You can remotely operate the projector from the outside the Remote control range by connecting to the REMOTE terminal.

Pin assignments and signal names

	Pin No.	Signal name	Contents

	A	GND	Ground

	B	POWER	POWER ON

	C	INPUT SEL3	Select input signal 3

	D		NC

	E	INPUT SEL1	Select input signal 1

	F	INPUT SEL2	Select input signal 2

	G		Connect internally

	H
	H

	I	ENABLE	Control by external contact

LAMP switching

Pin No.						Settings

B - A				Short				Open

Operation					On			Off

Switching input		signals

Pin No.					Settings

C - A	Open		Open		Short	Short		Short	Open
E - A	Open		Short		Open	Open		Short	Short
F - A	Open		Open		Short	Open		Open	Short
Input signal	COMPUTER1		COMPUTER2		COMPONENT	VIDEO		S-VIDEO	NETWORK
Input signal	COMPUTER1		COMPUTER2		COMPONENT	VIDEO		S-VIDEO	(PT-F200NTU
									only)


NOTE:

•When pin A and pin I are short-circuited, the buttons on the projector’s control panel, POWER and INPUT SELECT buttons on the Remote control cannot be used. In addition, the RS-232C commands and network functions that correspond to these functions cannot be used either.

•While pin I is “Open”, do not short-circuit pin A, B, C, E and F. The projector would reject all the signals from the Remote control.

Appendix

ENGLISH - 47

Image 47

Contents PT-F200U Model number PT-F200NTU / PT-F200U Important Safety NoticePanasonic Important Safety NoticeDeclaration of Conformity Model Number PT-F200NTU / PT-F200U Trade NameContents Appendix SettingsMaintenance Precautions with regard to safety Use only the specified batteries Precautions with regard to safetyDo not set up the projector outdoors Do not look into the lens while the projector is being usedElectric shocks can result if this is not done Remove the used batteries from the remote control promptlyDo not put your weight on this projector Do not mix old and new batteriesSecurity AccessoriesRead this first Minimum required setting screenAbout Your Projector Remote controlControl panel Projector bodyAbout Your Projector Top and front viewOutput by menu operation About Your Projector Back and bottom viewComputer. Selectable for input Projected image Screen Setting upCalculation methods for screen dimensions Screen size and throw distanceMounting in the ceiling and projecting from front Front leg adjusters and throwing angleSetting up Projection methodVertical shift Adjusting the Lens shift leverLens shift and positioning Horizontal shiftWhen the projector position is fixed Setting up Projector location rangeWhen the screen position is fixed LAN terminal Connecting example ComputersConnections Before connection to the projectorConnections Connecting example AV equipmentsConnecting with Video IN/S-VIDEO Connecting with ComponentPower indicator Switching the projector on/offPower cord Switch the Main Power on Press the Power button Switching on the projectorSwitching off the projector Switching the projector on/offFocus lever Zoom lever Selecting the input signalProjecting an image Positioning the imageFacing to the projector Remote control operationSetting up the image position automatically Operating rangeUsing the laser pointer Switching the input signalStopping the projection temporary Resetting to the factory default settingsProjecting an image in INDEX-WINDOW mode Capturing an imageShifting the center point Controlling the volume of the speakerEnlarging the centered area Enlarging the imageDisplaying the Main menu Adjusting with the bar scale itemsMenu Navigation Navigating through the MenuMenu Navigation Main menu and Sub-menuWEB Control Live Mode CUT Status InitializeAudio Balance Network StandbyPicture menu For RGB signals Detailed SetupFor S-VIDEO/VIDEO signals Position menu Position menu When the Resizing is set to OFFResizing Frame LockOption menu Signal Search Power OFF TimerDirect Power on Auto SetupTest Pattern SettingClosed Caption Text Display Input PasswordPassword Change Security menuNetwork menu, the following items are available Network menuItems in Network menu Temp indicator LAMP, Temp and ARF IndicatorsManaging the indicated problems Lamp indicatorReplacing the ARF Auto Rolling Filter Care and ReplacementCleaning the projector Before replacing the Lamp unit Care and Replacement Resetting the FilterWhen to replace the Lamp unit Replacing the Lamp unitRemoving and replacing the lamp unit Ceiling mount bracket safeguardsCare and Replacement Replacement procedure Installing the safety cableTroubleshooting Dots*1 KHz MHz List of compatible signals Technical Information Quality*2Serial terminal Projector Technical Information Cable specificationsControl commands Computer connection guidanceRemote terminal Lamp switchingSwitching input Signals Specifications Computer Audio COMPUTER1OUT AudioScreen height SH Screen width SW Minimum distance Screen size and throw distance for 169 aspect ratioProjection size 16 Throw distance L These Operating Instructions are printed on recycled paper DimensionsTrademark acknowledgements Unit mmCalculation methods IndexALS Ambient Luminance Sensor ARF Auto Rolling FilterTechnical Information IndexNavigation buttons Screen sizeNuméro de série Avis important concernant la sécuritéNuméro de modèle PT-F200NTU / PT-F200U Déclaration de conformité Avis important concernant la sécuritéAvertissement Avertissements Précautions de sécuritéPrécautions de sécurité Mises EN GardeSinon cela peut causer des chocs électriques Utiliser uniquement les piles spécifiéesNe pas mélanger des piles usées et des piles neuves Précautions lors de lutilisation Précautions lors de linstallationPrécautions lors du transport Avant de remplacer le lUnité de la lampe Remplacement de lunité de la lampeDélai de remplacement de lUnité de la lampe «LAMPE DE REMPLACEMENT» estDe lUnité de La lampe Installation du câble de sécuritéProtections du support de montage au plafond Retirer et remplacer la lampeTechnical Support Panasonic Projector Systems Company