Panasonic PT-LB51NTU Switching the projector on/off, Power cord, POWER indicator, Connecting

Page 20
Basic Operation

Basic Operation

Switching the projector on/off

Power cord

Connecting

1.Make sure the shape of the power cord plug and the AC IN connector on the back of the projector match, then push the plug all the way in.

2. Connect the Power cord to a wall outlet.

Disconnecting

1.Check that the POWER indicator of the POWER button is lit red, and then unplug the Power cord from the wall outlet.

2.Hold the plug and unplug the Power cord from the AC IN connector on the back of the projector.

Direct power off function

You can disconnect the Power cord during projection or immediately after use and move the projector. The cooling fan will operate by the internal power supply to cool down the lamp.

When this function is used, it may take more time for the lamp to turn back on again compared to when the lamp cools down with the Power cord connected.

Do not put the projector in a bag while the POWER button on the projector is illuminated.

Direct power on function

If you activate the DIRECT POWER ON, you can start the projection only with connecting the Power cord. See “DIRECT POWER ON” on page 35.

NOTE:

Do not use other than a provided Power cord.

Ensure all the input devices are connected and turned off before connecting the Power cord.

Do not force the connector as this may damage the projector and/or the Power cord.

Dirt or dust build-up around plugs may cause fire or electrical hazards.

Switch off the power to the projector when not in use.

POWER indicator

POWER indicator

Indicator status

Status

 

 

 

 

 

The projector is in standby.

RED

Lit

When the LAMP or TEMP indicator is flashing, the POWER indicator will

 

 

not be lit.

 

 

 

GREEN

Flashing

The POWER is switched on and the projector is getting ready to project.

 

 

Lit

The projector is ready to project.

 

 

 

 

 

Lit

The POWER is switched off and the projector is cooling the lamp.

ORANGE

 

 

Flashing

The POWER is switched on again when cooling the lamp and recovering

 

 

to projection mode. Recovery may take a while.

 

 

 

 

 

NOTE:

If the projector is switched on again while the internal cooling fan is still operating by the internal power supply, it may take a while to start the projection.

The electric consumption in standby mode is 4 W.

ENGLISH - 20

Image 20
Contents LCD Projector Commercial Use AUTO SETUP INPUT SELECT COMPUTER WIRELESS VIDEOWIRELESS PAGE PRESENTATION MENU RETURN ENTER FREEZE SHUTTER COMPUTER DEFAULT SEARCH INDEX-WINDOWImportant Safety Notice Dear Panasonic CustomerENGLISH Important InformationImportant Safety Notice Declaration of ConformityPanasonic Information on Disposal in other Countries outside the EuropeanContents 1. Set up your projector5. Adjust the image Important InformationSettings MaintenanceSettings Basic Operation Getting Started Preparation Maintenance AppendixImportant Information Precautions with regard to safetyWARNINGS Precautions with regard to safety CAUTIONSCautions when transporting Cautions when installingImportant Information AccessoriesCautions on use Remote control About Your ProjectorPreparation POWER buttonAbout Your Projector Attaching a hand strapProjector body Top and front viewControl panel Control panel Font leg adjusterConnector Panel Back and bottom viewConnector Panel Lamp unit compartment page Font adjustable legs L/R Adjust the projection angle. pageSetting up Screen size and throw distanceStarted PT-LB51NTU/PT-LB51USetting up Calculation methods for screen dimensions GettingSetting up Setting on a desk/floor and projecting from frontSetting on a desk/floor and projecting from rear Projection methodFront adjustable legs and throwing angle If keystone distortion occurs, see “KEYSTONE” on pageBefore connection to the projector Connecting with computersConnections Connecting with AV equipment Connecting with VIDEO IN/S-VIDEO INConnecting with COMPONENT IN ConnectionsSwitching the projector on/off Power cordPOWER indicator ConnectingSwitching the projector on/off Switching on the projectorSwitching off the projector Selecting the input signal Projecting an imagePositioning the image Zoom ring Focus ringRemote control operation Setting up the image position automaticallyOperating range BasicSwitching the input signal Remote control operationPressing the WIRELESS button Capturing an imageResetting to the factory default settings Remote control operationSwitching the position Projecting an image in INDEX-WINDOW modeControlling the volume of the speaker Enlarging the centered areaEnlarging the image Shifting the center pointOperating procedure Adjusting with the bar scaleSettings Menu NavigationMain menu and Sub-menu Menu NavigationMenu Navigation PICTURE menu PICTURE MODECOLOR TINTDETAILED SETUP For RGB signalsFor S-VIDEO/VIDEO signals DAYLIGHT VIEWCLOCK PHASE POSITION menuREALTIME KEYSTONE KEYSTONES1 video signals LANGUAGE menuRESIZING FRAME LOCKLAMP POWER OPTION menuINPUT GUIDE FUNCTION BUTTONPOWER OFF TIMER AUTO SETUPSIGNAL SEARCH DIRECT POWER ONHIGHLAND INDEX-WINDOWSHUTTER OSD DESIGNPASSWORD CHANGE INPUT PASSWORDAfter you change the password SECURITY menuItems in WIRELESS menu WIRELESS menu PT-LB51NTU onlyINPUT PASSWORD PASSWORD CHANGETEMP, LAMP Indicators Managing the indicated problemsLAMP indicator TEMP indicatorCare and Replacement Cleaning the projectorBefore cleaning the projector Cleaning the outer surface of the projectorCare and Replacement When to replace the Lamp unitReplacing the Lamp unit Before replacing the Lamp unitHandles lamp unit fixing screws Lamp unit coverlamp unit cover fixing screws Troubleshooting Should any problem persist, contact your dealerList of compatible signals Technical InformationPin assignments and signal names Communication settingsSerial terminal Technical InformationTechnical Information Cable specifications Control commandsProjector PC DTEComputer connection guidance The computer connection guidance will disappear after 5 minutesSpecifications Appendix Dimensions Units mm inchThese Operating Instructions are printed on recycled paper Trademark acknowledgmentsAll other trademarks are the property of the various trademark owners Index Index Avis important concernant la sécurité Cher client PanasonicFRANÇAIS Imformation ImportanteAvis important concernant la sécurité Information ImportantePrécautions de sécurité AVERTISSEMENTMISES EN GARDE Précautions de sécuritéPrécautions lors du transport Information ImportantePrécautions lors de linstallation Précautions lors de lutilisationRemplacement de lunité de la lampe Délai de remplacement de lUnité de la lampeAvant de remplacer le lUnité de la lampe REMARQUERemplacement de lunité de la lampe Procédure de remplacement Panasonic Projector Systems Company Technical SupportProjectors Unit of Panasonic Corporation of North America