Panasonic PT-LB51U manual Setting up Calculation methods for screen dimensions

Page 15

Setting up

Calculation methods for screen dimensions

You can calculate more detailed screen dimension from the screen diagonal. (Unit: m)

PT-LB51NTU/PT-LB51U

Projection size(4:3)

SH

= SD X 0.0152

SW

= SD X 0.0203

LW

= 0.0307 X SD - 0.031

LT

= 0.0371 X SD - 0.029

Projection size(16:9)

SH

= SD X 0.0125

SW

= SD X 0.0221

LW

= 0.0335 X SD - 0.0315

LT

= 0.0405 X SD - 0.0365

PT-LB51SU

Projection size(4:3)

SH

= SD X 0.0152

SW

= SD X 0.0203

LW

= 0.0304 X SD - 0.029

LT

= 0.0368 X SD - 0.041

Projection size(16:9)

SH

= SD X 0.0125

SW

= SD X 0.0221

LW

= 0.0332 X SD - 0.032

LT

= 0.0401 X SD - 0.038

Started

* The results above are approximate and may differ slightly from the actual measurements.

NOTE:

• Do not use the projector at a raised or a horizontally tilted position as it may cause malfunction of the projector.

• Make sure the projector lens surface is parallel with the screen. You can tilt the projector body approximately ± 30° vertically. Overtilting may result in shortening the component’s life.

For the best quality of the projection image, install a screen where sun light or room light does not shine directly onto the screen. Close window shades or curtains to block the lights.

Getting

ENGLISH - 15

Image 15
Contents PT-LB51U PT-LB51SU Model number PT-LB51NTU / PT-LB51U / PT-LB51SU Important Safety NoticePanasonic Important Safety NoticeDeclaration of Conformity Model Number PT-LB51NTU / PT-LB51U / PT-LB51SU Trade NameContents Settings MaintenanceAppendix Precautions with regard to safety Use only the specified batteries Precautions with regard to safetyDo not set up the projector outdoor Do not look into the lens while the projector is being usedRemove the used batteries from the remote control promptly Do not put your weight on this projectorDo not mix old and new batteries Accessories About Your Projector Remote controlControl to adjust the volume of the speakers. Battery compartmentAttaching a hand strap About Your ProjectorProjector body Top and front viewControl panel Back and bottom view Connector PanelProjection size 4 Throw distance L Height Screen Setting upScreen size and throw distance Projected image ScreenSetting up Calculation methods for screen dimensions Mounting in the ceiling and projecting from rear Setting upProjection method Mounting in the ceiling and projecting from frontFront adjustable legs and throwing angle Connecting with computers ConnectionsBefore connection to the projector Connections Connecting with AV equipmentConnecting with Video IN/S-VIDEO Connecting with ComponentSwitching the projector on/off Power cordPower indicator Plug the Power cord into the projector Switching on the projectorSwitching off the projector Switching the projector on/offSelecting the input signal Projecting an imagePositioning the image Facing to the projector Remote control operationSetting up the image position automatically Operating rangeSwitching the input signal Capturing an imageStopping the projection temporary Changing the image size Resetting to the factory default settingsProjecting an image in INDEX-WINDOW mode Switching the positionShifting the center point Controlling the volume of the speakerEnlarging the centered area Enlarging the imageNavigating through the Menu Menu NavigationMenu Navigation Main menu and Sub-menuLive Mode CUT Status Initialize See CD-ROM contents for detailed informationOnly Picture menu Daylight View Detailed SetupFor RGB signals For S-VIDEO/VIDEO signalsPosition menu Frame Lock S1 video signalsLanguage menu ResizingOption menu Direct Power on Power OFF TimerAuto Setup Signal SearchSolid blue You can perform more detailed setting in various itemsHighland Semi transparent blackText Display Password ChangeInput Password Security menuWireless menu, the following items are available Items in Wireless menuTemp indicator TEMP, Lamp IndicatorsManaging the indicated problems Lamp indicatorCare and Replacement Cleaning the projectorReplacing the air filter Before replacing the Lamp unit Care and ReplacementWhen to replace the Lamp unit Replacing the Lamp unitHandles lamp unit fixing screws Lamp unit cover Lamp unit cover fixing screwsTroubleshooting Technical Information List of compatible signalsSerial terminal Technical Information Cable specifications Control commandsProjector Computer connection guidance Manufacturer Key commandSpecifications Variable Audio OUTAudio Computer AudioDimensions Trademark acknowledgments Index Index Avis important concernant la sécurité PT-UX71NT/PT-UX71Numéro de série Déclaration de conformité Avis important concernant la sécuritéAvertissement AdvertenciaAvertissement Précautions de sécuritéPrécautions de sécurité Mises EN GardeSinon cela peut causer des chocs électriques Précautions lors du transportUtiliser uniquement les piles spécifiées Ne pas mélanger des piles usées et des piles neuvesÉcran Précautions lors de linstallationPrécautions lors de lutilisation Affichage à cristaux liquidesRemplacement de lunité de la lampe Délai de remplacement de lUnité de la lampeAvant de remplacer le lUnité de la lampe Poignées Vis de fixation du bloc de lampe Remplacement de lunité de la lampe Procédure de remplacementTechnical Support Panasonic Projector Systems Company