Panasonic PT-L735NTE Rgb/Ypbpr, Blackboard, Back Color, Front/Rear, Desk/Ceiling, FAN Control

Page 24

RGB/YPBPR

This setting is valid when 750p, HDTV60, HDTV50, 525p, 625i and 525i signals are being input. Select the setting in accordance with the input signal.

The RGB/YPBPR item is displayed when the RGB1 IN or RGB2 IN connector has a signal being input.

VGA60/525P

When a VGA60 or 525p RGB signal is being input, select the signal in accordance with the input signal.

BLACKBOARD

Set to “ON” when PICTURE MODE is set to BLACKBOARD. (Refer to page 37.)

BACK COLOR

This sets the colour which is projected onto the screen when no signal is being input to the projector.

FRONT/REAR

This setting should be changed in accordance with the projector setting-up method.

Set to “FRONT” when using a normal reflective screen with the projector positioned in front of the screen, and set to “REAR” when using a translucent screen with the projector positioned behind the screen.

DESK/CEILING

This setting should be changed in accordance with the projector setting-up method.

Set to “DESK” when setting up the projector on a desk or similar, and set to “CEILING” when suspending the projector from the ceiling using the ceiling bracket which is sold separately.

FAN CONTROL

Set FAN CONTROL to “HIGH”, when using this projector at high elevations (above 1 400 m) only.

LAMP POWER

This setting changes the lamp brightness. When set to “LOW”, the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. This can help to extend the lamp’s operating life. If using the projector in small rooms where high luminance is not required, it is recommended that you set the LAMP POWER to “LOW”.

LAMP RUN TIME

This setting displays the usage time for the lamp unit which is currently being used.

NOTE:

BThe lamp’s operating life varies depending on the usage conditions (such as the LAMP POWER setting and the number of times the power is turned on and off).

FUNC 1

This assigns a function to the FUNC1 button of the remote control unit .

MUTE

Functions in the same way as the MUTE function. (page 44)

KEYSTONE

Functions in the same way as when “KEYSTONE” is selected from the POSITION menu screen. (page 41)

CONTROL KEY

To disable the buttons on the projector, set CONTROL KEY to “OFF”. A confirmation screen will then be displayed. Select “OK” by using I and H buttons. To use the buttons on the projector, set to “ON” by using the remote control unit.

AUTO POWER OFF

If any signal is not input into the projector during the time that you set up, the projector will return to standby mode. The auto power off time can be set to, from 15 minutes to 60 minutes, by 5 minutes. If you don't use this feature, set it to “DISABLE”. This feature will not function under the following situation.

1)When using the freeze function.

2)When the NETWORK or SD CARD is selected (PT-L735NTE only).

3)When writing the data in the SD memory card (PT-L735NTE only).

NOTE: (PT-L735NTE only)

BWhen the projector is connected to a personal computer by means of the wireless network using the accessory wireless card, the projector will go in the WEB STANDBY. (page 48)

Adjustments and settings

46-ENGLISH

ENGLISH-47

Page 23 Page 25
Image 24
Page 23 Page 25
Contents LCD Projector Commercial Use Model No. PT-L735NTEDear Panasonic Customer PreparationModel number PT-L735NTE / PT-L735E Important the Moulded Plug U.K. onlyContents Precautions with regard to safetyDo not handle the mains lead plug with wet hands Insert the mains lead plug securely into the mains socketDo not place the projector into water or let it become wet Do not place liquid containers on top of the projectorAccessories Do not put your weight on this projectorPT-L735NTE only Use only the specified batteriesAbout the wireless card and SD memory card PT-L735NTE only Before useDo not touch the surfaces of the lens with your bare hands About the screenLocation and function of each part Remote control unit Projector control panelPT-L735NTE only Wireless card SD memory card Setting-up Projection methodsProjector position Projection distancesExample of connecting to computer Example of connecting to video equipmentsConnections Monitor Computer for Control useTurning on the power # Presspower.the Main Power switch to turn on$Press the Power button Turn on the power of all connected devicesTurning off the power RGB Input indicator Press the Auto Setup buttonPOSITION, DOT CLOCK, Clock Phase Projector statusPausing a picture Freeze Turning off the picture and sound momentarily ShutterEnlarging the picture D.ZOOM Wireless mouse Mode switch Computer/ProjectorLaser beam pointer ButtonsOn-screen menus Menu screensMenu operation guide Adjusting the picture Returning a setting to the factory defaultPicture Mode Contrast BrightColor TintAdjusting the position Clock PhaseDOT Clock PositionAuto Setup OSD PositionAspect ResizingAudio adjustment Option settingsChanging the display language Lamp Power Auto Power OFFRGB/YPBPR BlackboardSetting up the Security function Text Display Change TextLogo Display Logo ClearLamp indicator Temp indicator Lamp indicatorLamp Power RemedyLamp unit replacement period Lamp unit replacement procedure Turn off the power+ Select the Lamp RUN Time by pressing the F or G buttons Press and hold the Enter button for approximately 3 secondsBefore calling for service Cleaning and maintenanceBefore carrying out cleaning and maintenance, be Sure to disconnect the mains lead plug from Mains socketSpecifications Remote control unitOptions List of compatible signals Connector pin wiring Projection dimensions calculation methodsAppendix Using the Serial connector Dimensions Trademark acknowledgements
Top Page Image Contents